Sharp AR-M455N Service Manual page 206

SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-2, AND PRESS START.
0. EXECUTE
1. HIGH 7 (dB) 2. HIGH-LOW
Select 1 or 2, and
press [START] key.
(When 1)
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1. HIGH(dB)
(When 2)
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1. HIGH(dB)
Select 0 and press [START] key.
(When 0)
SIMULATION 66-16
DIAL TEST(DTMF). EXECUTING···.
1. HIGH 7 (dB) 2. HIGH-LOW
66-17
Purpose Setting
Function Used to check the dial signal (DTMF) output in the
(Purpose) FAX tone dial mode. Send level: Max. Used to
check the operation. (Only when FAX is installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.
2) Press [START] key.
The signal is sent in the max. send level.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX)
PRESS START.
Press [START] key.
SIMULATION 66-17
DTMF SIGNAL OUTPUT.(LEVEL MAX)
66-18
Purpose Setting
Function Used to check the dial signal (DTMF) output in the
(Purpose) FAX tone dial mode. An output is sent at the send
level set by the soft switch. Used to check the
operation. (Only when FAX is installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.
2) Press [START] key.
1
7
Press [CUSTOM SETTINGS] key
or press [START] key.
7
7
Press [CUSTOM SETTINGS] key.
7
INPUT 0-9, *, #, AND
1
Press [CUSTOM SETTINGS] key.
EXECUTING···.
1
AR-M355N/M455N SIMULATION 9 - 80
The signal is sent in the send level set with the soft SW.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW.) INPUT 0-9, *, #, AND PRESS
START.
Press [START] key.
SIMULATION 66-18
DTMF SIGNAL OUTPUT.(SOFT SW.)
66-19
Purpose Data transfer
Function Used to back-up the HDD data into the Flash
(Purpose) memory (optional FAX expansion memory: AR-
MM9). (Only when FAX is installed)
Section FAX
Item Data
Operation/Procedure
1) Select YES/NO of data transfer (backup).
1 YES Backup is executed.
2 NO Backup is not executed.
2) Press [START] key.
This function is valid only when the AR-MM9 is installed.
Backup contents
• Address book data (FAX, Mail, Address)
• One-touch dial
• FTP expansion
• Group expansion
• Program
• Use index
• Standard sender
• IFAX sender registration
• FAX sender registration
The other contents are not backed up.
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)
ARE YOU SURE?
1. YES
2. NO
Press [START] key.
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
After completion of backup
1
Press [CUSTOM SETTINGS] key.
EXECUTING···.
1
• Item name
• Fine name
• FAX receive select table
• IFAX receive YES/NO
• Polling allow number
• Memory box
• Sender name
• Soft SW
1
1