Sharp AR-M455N Service Manual page 197

64
64-1
Purpose Operation test/Check
Function Used to check the operation of the printer section
(Purpose) (self-print operation), (The print pattern, the paper
feed mode, the print mode, the print quantity, and
the density can be optionally set.)
Item Operation
Operation/Procedure
(Various print patterns output) (Table 1)
1) Select PRINT PATTERN with 10-key.
2) Enter the number corresponding to the print pattern to be
printed with 10-key.
3) Press [START] key.
4) Select PRINT START with 10-key.
5) Press [START] key.
(Print condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Select TRAY SELECT with 10-key.
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
∗ To adjust the print density, perform the following procedures.
1) Select DENSITY with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
∗ To set the print quantity, perform the following procedures.
1) Select MULTI with 10-key.
2) Enter the print quantity with 10-key.
3) Press [START] key.
∗ To set the print quality mode, perform the following procedures.
1) Select MODE with 10-key.
2) Enter the number corresponding to the print quality mode with
10-key.
3) Press [START] key.
∗ To set the print level, perform the following procedures.
1) Select LEVEL with 10-key.
2) Enter the adjustment value with 10-key.
3) Press [START] key.
NOTE: In some print patterns, changing the level may not change
the picture quality.
∗ To set duplex/simplex print, perform the following procedures.
1) Select DUPLEX with 10-key.
2) Enter the number corresponding to the operation mode with
10-key.
3) Press [START] key.
(Table 1)
0 TRAY SELECT
1. TRAY1
2. TRAY2
3. TRAY3
4. TRAY4
5. BPT
1 PRINT START
2 PRINT PATTERN
3 DENSITY
4 MULTI
5 MODE
1. STANDARD
2. SMOOTHING
3. TONER SAVE
4. HALF TONE
5. SMOOTHING + TONER
SAVE
6. SMOOTHING + HALF TONE
7. TONER SAVE + HALF
TONE
8. SMOOTHING + TONER
6 LEVEL
7 DUPLEX
1. NO
2. YES
(Note 1) Print pattern
Engine
No
pattern
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
AR-M355N/M455N SIMULATION 9 - 71
Paper feed tray
1: Tray 1
2: Tray 2
3: Tray 3
4: Tray 4
5: Manual feed
Print execution (Printing of the set
data is executed.)
Print pattern (Note 1)
Graphic density (Valid only when
No. 79, 80 or 84 is selected.)
Print quantity
Print mode
1. Standard
2. Smoothing ON
3. Smoothing ON
3. Toner save ON
4. Half tone ON
5. Smoothing + toner save
6. Smoothing + half tone
7. Toner save + half tone
8. Smoothing + toner save +
half tone
SAVE + HALF TONE
(Parameter of print image
process)
Duplex
0: NO (Simplex)
1: YES (Duplex)
Controller Pattern
❍
For off-center adjustment
❍
Main scanning direction 1 by 5
❍
Main scanning direction 1mm-
pitch
❍
Main scanning direction 3 by 3
❍
Sub scanning direction 1 by 1
❍
Sub scanning direction 1 by 5
❍
Sub scanning direction 2 by 4
❍
Sub scanning direction 3 by 3
❍
Right oblique 1 by 2
❍
Right oblique 1 by 5
❍
Right oblique 2 by 4
❍
Right oblique 3 by 3
❍
Left oblique 1 by 2
❍
Left oblique 1 by 5
❍
Left oblique 2 by 4
❍
Left oblique 3 by 3
❍
Dot 1 by 1
❍
Dot 3 by 3
❍
Dot
❍
Solid black
❍
Main scanning direction 1 by 1
❍
Main scanning direction 5 by 1
❍
Main scanning direction 4 by 2
❍
Main scanning direction 3 by 3
❍
Sub scanning direction 1 by 1
❍
Sub scanning direction 5 by 1
❍
Sub scanning direction 4 by 2
❍
Sub scanning direction 3 by 3
❍
Right oblique 2 by 1
❍
Right oblique 5 by 1
❍
Right oblique 4 by 2
❍
Right oblique 3 by 3
❍
Left oblique 2 by 1
❍
Left oblique 5 by 1
❍
Left oblique 4 by 2
❍
Left oblique 3 by 3
Note