Sharp AR-M455N Service Manual page 182

2) Check the lead edge void area on the self print pattern.
(Enter 1 and press [START] key.)
3) If the adjustment result is not satisfactory, perform the follow-
ing procedures.
∗ If the lead edge void area is not 3.5mm:
Change the adjustment value of RRCB and perform the
adjustment. (Change the adjustment value of RRCB and
press [START] key.)
(Shift for the adjustment value change: 0.1mm/step)
(Front/rear frame direction void area adjustment)
Adjust so that the total of the front/rear direction void areas is
7.0mm. (Change the adjustment values of FRONT/REAR, and
press [START] key.)
Front frame void area = 3.5mm
3.5mm
(Paper resist adjustment)
1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 3 - 9.) (Table 1)
2) Press [START] key.
3) Enter the adjustment value with 10-key.
4) Press [P] key or [START] key. When [START] key is pressed,
the adjustment value is set and printing is performed. (Table 2)
If the relative positions of paper and print images vary or a paper
jam occurs, change the adjustment value.
(Print condition setting in this simulation)
∗ To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key. (Select one of 1 - 5.) (Table 3)
4) Press [START] key. (The paper feed tray is selected.)
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex print mode.
NOTE: When [P] key is pressed after entering the adjustment
value in this simulation, the adjustment value is set. When
[START] key is pressed instead, the adjustment value is
set and copying is performed.
(Table 1)
Item
0 TRAY SELECT Paper feed tray
selection
1 PRINT START Print start (Default)
(Lead edge adjustment value)
2 RRCB Resist roller clutch
ON timing
adjustment value
3 SIDE2 ADJ. Correction value
for RRCB when
refereeing from
ADU
(Resist adjustment value)
4 T1 Tray 1 adjustment
5 T2 Tray 2 adjustment
6 DESK Tray 4 adjustment
7 BPT Manual feed tray
adjustment
8 ADU Adjustment when
paper is fed again
from ADU
Rear frame void area =
Default
Set
AR- AR-
range
M355N M455N
1 - 5 –
– –
0 - 99 50
50
0 - 99 65 60
Select 0, and
press [START] key.
55 50
55 50
60 55
55 50
AR-M355N/M455N SIMULATION 9 - 56
Item
(Off-center set value) Self print
9 T1 Tray 1 adjustment
10 T2 Tray 2 adjustment
11 T3 Tray 3 adjustment
12 T4 Tray 4 adjustment
13 BPT Manual feed tray
adjustment
14 ADU Adjustment when
paper is fed again
from ADU
(Void set value)
15 LEAD_EDGE Lead edge void set
(DENA) value
16 TRAIL_EDGE Rear edge void
(DENB) adjustment value
17 FRONT/REAR Front/Rear void
adjustment value
(Table 2)
Normal display
ERROR display Door open
Jam
Paper empty
(Table 3)
1 TRAY1
2 TRAY2
3 TRAY3
4 TRAY4
5 BPT
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB 50
RESIST: 4.T1 50 5.T2
7.BPT 50 8.ADU
OFF CENTER: 9.T1 50 10.T2
13.BPT 50 14.ADU
(VOID SETTING) 15.LEAD_EDGE(DENA)
16.TRAIL_EDGE(DENB)
Select other than 0 - 1, and press [START] key.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
START.
2.RRCB
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. NOW PRINTING.
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
(ABOVE+10: DUPLEX MODE)
Default
Set
AR- AR-
range
M355N M455N
0 - 99 50
0 - 99 35
32
NOW PRINTING.
DOOR OPEN.
JAM
PAPER EMPTY.
TRAY1
TRAY2
TRAY3
TRAY4
Manual feed
2
3.SIDE2 ADJ. 50
50 6.DESK 50
50
50 11.T3 50 12.T4 50
50
35
35 17.FRONT/REAR
Press [CUSTOM SETTINGS] key.
50
Press [CUSTOM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [CUSTOM SETTINGS] key.
1
32