JUKI DDL-5530N Handbook page 55

Model Part No.
Blind hemming device
L121 MAL-121000A0 Blind stitch hemming attachment
MAL-122001A0
Automatic folded-edge controlled blind hemming device
MAL-122002A0
(The attachment automatically detects the overlapped
L122
section of a material. Then, it makes the needle enter the
MAL-122001AA
material deeper to prevent stitch deviation.)
MAL-122002AA
Spring-type folded-edge controlled bottom hemming
L123 MAL-123000A0
device
Piping folder
M056 MAM-0560J0A0 Piping folder
M075 MAM-0750J0A0 Piping folder (to be used with knit tape)
M076 MAM-0760N0A0 Ready-made piping folder
M077 MAM-0770M0A0 Piping folder for shirring
Guide, Ruller
H153 MAH-153000A0 Cloth edge guide ruler (for overlock machine)
H154 MAH-154000A0 Cloth edge guide ruler (for safety stitch machine)
Q141 MAQ-141000B0 Tape guide
S084D MAS-084000AD Pattern guide
Feller, Binder
K006 MAK-00601000 Upturn feller
N067 MAN-0670D0A0 Reinforcement tape attachment binder
N077 MAN-077000A0 Clean finish top and bottom
Miscellaneous
Backlach device
Z173 MAZ-173000A0
(for 1-needle overlock machine )
Needle thread tension releasing device
Z175 MAZ-175000A0 (for 1-needle overlock machine with needle thread
releasing device)
118-55954 Needle cooler (for overlock machine)
118-56051
Needle cooler (for safety stitch machine)
121-47203 Cloth waste cover (for overlock machine)
Cloth waste cover
121-47302
(for overlock machine, overedging width 8mm over)
121-03305 SS-7091410SP
121-03511 SS-6111440SP
118-02402 NS-6110420SP
SS-7110710SP 2 121-02810
121-38400 121-38301
121-38152 TA-0950806R0
Cloth puller
V058A
V058B Electromagnetic cloth puller (top and bottom roller type)
V058C
V068A
Pneumatic cloth puller (top and bottom roller type)
V068C
MO-3900 SERIES (June, 2001) 6/6
Description
121-02950
121-03107
118-02006
SM-4040855SP
Feature
A ruler used for blind hemming in knits
For 110, 115, 220, 240V
Flat upper
knife
For 220, 380, 415, 440V
For 110, 115, 220, 240V
Square upper
knife
For 220, 380, 415, 440V
When the overlapped section of a material is reached,
the blind hemming guide will move sufficiently to
prevent stitch deviation.
This piping folder makes a piping first, then turns up the
tape.
This attachment can be used for both "cotton bias tape
with gimp" and "knit tape". The operation mode can be
changed over with a fingertip control.
The dimension of ready-made tapes can be adjusted
within the range of 8 to 13mm.
The attachment makes gathers on the lower fabric while
making decorative piping.
A swing type edge guide
This attachment is used attached on the machine head
(face plate). It is used for tapes with the width of 7mm
or less
This attachment is used for overedging a sleeve bottom
placket with a sharp curve.
It enables the machine to smoothly sew the curved
section of a sleeve bottom placket along with the guide
pin of the presser foot.
This feller is exclusively used with the 3C0 throat plate. It
is attached on the throat plate.
This binder binds the edge of a pocket bag while cutting
round its periphery.
This binder runstitches a pocket bag and binding its
periphery with tape simultaneously.
It sews chain-off thread at the start of sewing inside
overedged seam. With this device, the operator is no
longer required to neatly arrange the chain-off thread.
Rolled-in chain-off thread also works as a simplified
bartack.
When making chain-off thread, the attachment reduces
the needle thread tension to make soft-chains. It is used
in combination with the Z173.
Needle cooler
By silicon oil lubricating unit for the needle tip.
Nedle thread heat remover
By silicon oil lubricating unit for the needle thread.
For table top type
For semi-sunken type
For fully-sunken type
For table top type
For fully-sunken type
Application
MO- MO- MO-
3600 3700 3900
S
S
S: Provided as standard