Flat bezel panel pc with 2nd generation intel core i7/i5/i3 or celeron cpu, wi-fi, touchscreen, rfid reader, gbe lan, rs-232/422/485, camera (141 pages)
Summary of Contents for IEI Technology afl2-w15b-h61
Page 1
AFL2-W15B-H61 IEI Technology Corp. MODEL: AFL2-W15B-H61 Series Flat Bezel Panel PC with 2nd Generation Intel® Core™ i7/ i5/ i3, Pentium® and Celeron® Processor, Touchscreen, Wi-Fi, USB, GbE LAN , RS-232/422/485, 1.3M Pixels Camera, HD Audio and RoHS User Manual User Manual Page I Rev.
Page 2
AFL2-W15B-H61 Revision Date Version Changes Initial release 13 September, 2012 1.00 Page II...
Page 3
AFL2-W15B-H61 Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
AFL2-W15B-H61 Table of Contents 1 INTRODUCTION......................4 6 4 H 1 .1 O ........................VERVIEW 4 6 5 H 1 .1.1 Model Variations ....................4 6 6 H 1 .1.2 Features ......................4 6 7 H 1 .1.3 Light Fanless Technology Design ..............
Page 5
AFL2-W15B-H61 3 .9 R ....................ESET THE YSTEM 2 9 H 4 9 3 H 3 .10 P ................... OWERING N THE YSTEM 3 0 H 4 9 4 H 3 .11 P .................. OWERING FF THE YSTEM 3 1 H 4 9 5 H 3 .12 M...
Page 6
NSTALLATION 9 1 H 5 5 5 H 6 SYSTEM MONITORING: ICMC ................1 12 9 2 H 5 5 6 H 6 .1 IEI C CMC) ............. 1 13 OOLING ANAGEMENT ONSOLE 9 3 H 5 5 7 H 6 .1.1 iCMC Installation ...................
Page 7
AFL2-W15B-H61 6 .2.1 Information Panel ................... 1 16 9 6 H 5 6 0 H 6 .2.2 Chart Panel..................... 1 19 9 7 H 5 6 1 H 7 SYSTEM MAINTENANCE ..................1 21 9 8 H 5 6 2 H 7 .1 S...
Page 8
AFL2-W15B-H61 8 .2.18 SATA Connector (SATA1)................1 39 1 2 9 H 5 9 3 H 8 .2.19 SATA Power Connector (CN8)..............1 39 1 3 0 H 5 9 4 H 8 .2.20 Speaker Connector (SPK_CN13)..............1 40 1 3 1 H 5 9 5 H 8 .2.21 SPI Flash Connector (JSPI1)...............
Page 9
AFL2-W15B-H61 C ONE KEY RECOVERY................... 1 56 1 6 3 H 6 2 7 H C .1 O ..............1 57 ECOVERY NTRODUCTION 1 6 4 H 6 2 8 H C .1.1 System Requirement ..................1 58 1 6 5 H 6 2 9 H C .1.2 Supported Operating System.................
AFL2-W15B-H61 List of Figures F igure 1-1: AFL2-W15B-H61 Flat Bezel Panel PC................ 1 9 2 H 6 5 6 H F igure 1-2: Front View ........................1 9 3 H 6 5 7 H F igure 1-3: LED Indicators......................1 9 4 H 6 5 8 H F igure 1-4: Function Keys ......................
Page 11
AFL2-W15B-H61 F igure 3-24: Stand Mounting (Stand-A/Bxx) ................2 2 3 H 6 8 7 H F igure 3-25: Audio Connector ..................... 2 2 4 H 6 8 8 H F igure 3-26: HDMI Connection ....................2 2 5 H 6 8 9 H F igure 3-27: LAN Connection ......................
Page 12
F igure 8-1: Main Board Layout Diagram ................. 1 31 2 9 1 H 7 5 5 H F igure C-1: IEI One Key Recovery Tool Menu ................ 1 57 2 9 2 H 7 5 6 H Page XII...
Page 13
AFL2-W15B-H61 F igure C-2: Launching the Recovery Tool ................1 62 2 9 3 H 7 5 7 H F igure C-3: Recovery Tool Setup Menu .................. 1 62 2 9 4 H 7 5 8 H F igure C-4: Command Prompt ....................
Page 14
AFL2-W15B-H61 F igure C-37: Backup System....................1 84 3 2 8 H 7 9 2 H F igure C-38: System Backup Complete Window ..............1 84 3 2 9 H 7 9 3 H F igure C-39: Restore Backup ....................
AFL2-W15B-H61 List of Tables T able 1-1: AFL2-W15B-H61 Model Variations................3 3 4 H 7 9 8 H T able 1-2: LED Indicators ......................3 3 5 H 7 9 9 H T able 1-3: Function Key Descriptions ..................3 3 6 H 8 0 0 H T able 1-4: System Specifications....................
Page 16
AFL2-W15B-H61 T able 8-26: Type K Thermocouple Connector (CN13, CN14) Pinouts........1 42 3 6 5 H 8 2 9 H T able 8-27: Webcam Connector (WEBCAMER1) Pinouts............1 42 3 6 6 H 8 3 0 H T able 8-28: Rear Panel Connectors ..................
Page 17
8 5 8 H B IOS Menu 14: Serial Port Console Redirection ............... 3 9 5 H 8 5 9 H B IOS Menu 15: iEi Feature......................3 9 6 H 8 6 0 H B IOS Menu 16: Chipset ........................
1.1 Overview Figure 1-1: AFL2-W15B-H61 Flat Bezel Panel PC The AFL2-W15B-H61 is a 2nd Generation Intel® Core™ i7/ i5/ i3, Pentium® or Celeron® processor powered flat bezel panel PC with a rich variety of functions and peripherals. The AFL2-W15B-H61 is designed for easy and simplified integration into kiosk and point-of-sales (POS) applications.
AFL2-W15B-H61 1.1.1 Model Variations The model variations of the AFL2-W15B-H61 Series are listed below. Model No. Touchscreen Type Optional Features Intel® Core i5 Series AFL2-W15B-H61-i5/PC-EM-R10 Projective capacitive EM card reader AFL2-W15B-H61-i5/PC-MF-R10 Projective capacitive MIFARE card reader AFL2-W15B-H61-i5/PC-R10 Projective capacitive...
8 7 0 H and dust free, like clean rooms, indoor HMI, and hospitals. 1.2 External Overview 1.2.1 Front Panel The front side of the AFL2-W15B-H61 is a flat bezel panel TFT LCD screen surrounded by a PC/ABS plastic frame. Page 4...
AFL2-W15B-H61 Figure 1-2: Front View 1.2.1.1 LED Indicators There are several LED indicators located along the bottom of the LCD screen ( F igure 8 7 1 H 1-3). Figure 1-3: LED Indicators The descriptions of each LED indicator are listed below.
Page 23
AFL2-W15B-H61 LED Indicator Description Off: power cord not attached or power supply failure Power Blinking amber: the system is connected to a power source and is ready to be turned on. Solid blue: the system is turned on. Power on/off by the hot keys. See...
AFL2-W15B-H61 indicators. Blinks when the corresponding button is LCD On/Off pushed. Audio Volume Down Audio Volume Up Brightness Down Brightness Up Table 1-2: LED Indicators WARNING: If the CPU temperature alert LED shows in red, the user must lower the environments temperature or close some running applications to cool down the CPU.
AFL2-W15B-H61 The function keys are described in T able 1-3: 8 8 1 H Key Combination Function Key Description Hold down Fn key for 3 seconds to enable/disable auto-dimming function. Fn + LCD On/Off Enable/Disable RFID Mute audio Fn + Audio Volume Down...
AFL2-W15B-H61 Figure 1-5: Rear View 1.2.3 Bottom Panel The bottom panel of the AFL2-W15B-H61 has the following connectors and switches F igure 1-6): 8 8 3 H 1 x AT/ATX switch 1 x Clear CMOS switch 1 x 9V ~ 36V DC input power jack...
AFL2-W15B-H61 Figure 1-6: Bottom Panel 1.2.4 Side Panels The side panels of the AFL2-W15B-H61 have the following features ( F igure 1-7): 8 8 4 H 2 x Audio jacks (Line-out, Mic-in) 1 x RJ-45 LAN connector 1 x USB 2.0 connector...
AFL2-W15B-H61 Figure 1-7: Side Panels 1.3 Dimensions The AFL2-W15B-H61 dimensions are shown below. Width: 399.4 mm Height: 271.2 mm Depth: 58.8 mm Page 11...
AFL2-W15B-H61 Figure 1-8: AFL2-W15B-H61 Dimensions (mm) 1.4 Internal Overview The AFL2-W15B-H61 has the following components installed internally: 1 x Motherboard 2 x 2.0 GB 1333 MHz DDR3 SO-DIMMs 1 x 802.11 b/g/n wireless LAN module Page 12...
AFL2-W15B-H61 1.5 System Specifications The technical specifications for the AFL2-W15B-H61 systems are listed in T able 1-4. 8 8 5 H Specification AFL2-W15B-H61 LCD Size 15.6" (16:9) Max. Resolution 1366 (W) x 768 (H) Brightness (cd/m2) Contrast Ratio 500:1 LCD Color 16.7M...
AFL2-W15B-H61 Front Panel Color Black Weight (N/G) 4.5 kg / 6.5 kg Dimensions (W x H x D) (mm) 399.4 x 271.2 x 58.8 Operating Temperature -20ºC ~ 50ºC Storage Temperature -20ºC ~ 60ºC Humidity 10% ~ 95% (no-condensing) IP level...
Pull the plastic cover off the flat bezel panel PC. Step 7: Make sure all the components listed in the packing list are present. Step 0: 2.1.1 Packing List The AFL2-W15B-H61 flat bezel panel PC is shipped with the following components: Quantity Item Image Standard AFL2-W15B-H61 panel PC...
Page 34
AFL2-W15B-H61 Power adapter (P/N: 63040-010090-020-RS) Power cord (P/N: 32702-000401-100-RS) Power transfer cord (P/N: 32702-000300-100-RS) RJ-45 to DB-9 COM Port Cable (P/N: 32005-000200-200-RS) OSD Remote Control (P/N: 7Z000-SLPCB005-RS) Temperature sensor cable (P/N: 32133-004300-100-RS) Pen for resistive touchscreen (P/N: 43125-0002C0-00-RS) M3 screw pack...
AFL2-W15B-H61 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL2-W15B-H61. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the AFL2-W15B-H61 is accessed internally, or any other...
Over-tightening back cover screws will crack the plastic frame. Maximum torque for cover screws is 5 kg-cm (0.36 lb-ft/0.49 Nm). To install the HDD into the AFL2-W15B-H61, please follow the steps below: Step 1: Remove two (2) retention screws from the HDD cover ( F igure 3-1).
AFL2-W15B-H61 Figure 3-1: HDD Cover Retention Screws Step 2: Remove the HDD cover from the device. Step 3: Loosen the captive screw to release the HDD bracket from the chassis. Slide the HDD bracket out of the device as shown ( F igure 3-2).
AFL2-W15B-H61 Figure 3-3: Inserting the HDD Step 5: Secure the HDD to the bracket using four (4) retention screws (two screws on each side) ( F igure 3-4). 8 8 9 H Figure 3-4: Securing the HDD Step 6: Slide the HDD module back into the device.
AFL2-W15B-H61 3.5 CF Card Installation The AFL2-W15B-H61 has one CF Type II slot under the HDD bay. To install the CF card, follow the instructions below. Step 1: Remove two (2) retention screws from the HDD cover ( F igure 3-1).
AFL2-W15B-H61 3.6 RFID Reader Installation (Optional) An optional RFID reader can be installed in the AFL2-W15B-H61. To install the RFID reader, follow the instructions below. Step 1: Remove a total of ten (10) retention screws from the back cover ( F igure 3-7).
AFL2-W15B-H61 Step 3: Install the RFID reader module in the location shown in F igure 3-9 by two 8 9 5 H retention screws. Figure 3-9: RFID Reader Module Installation Step 4: Connect the RFID module to the RFID connector on the main board (...
Step 0: 3.7 AT/ATX Mode Selection AT or ATX power mode can be used on the AFL2-W15B-H61. The selection is made through an AT/ATX switch located on the bottom panel. To select AT mode or ATX mode, follow the steps below.
Advertising terminal 3.8 Clear CMOS If the AFL2-W15B-H61 fails to boot due to improper BIOS settings, the clear CMOS switch clears the CMOS data and resets the system BIOS information. To do this, adjust the clear CMOS switch to clear CMOS mode for a few seconds then adjust the clear CMOS switch back to keep CMOS mode.
AFL2-W15B-H61 The five mounting methods are described below. 3.12.1 Wall Mounting To mount the flat bezel panel PC onto the wall, please follow the steps below. Step 1: Select the location on the wall for the wall-mounting bracket. Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.
Page 49
AFL2-W15B-H61 Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the four screw holes on the real panel of the flat bezel panel PC and tighten until the screw shank is secured against the rear panel ( F igure 3-15).
AFL2-W15B-H61 Figure 3-15: Chassis Support Screws Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. ( F igure 3-16). 9 0 7 H Figure 3-16: Secure the Panel PC Page 33...
AFL2-W15B-H61 3.12.2 Panel Mounting To mount the AFL2-W15B-H61 flat bezel panel PC into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the flat bezel panel PC. Step 2: Cut out a section corresponding to the size shown below. The size must be smaller then the outer edge.
Figure 3-18: Tighten the Panel Mounting Clamp Screws 3.12.3 Cabinet and Rack Installation The AFL2-W15B-H61 flat bezel panel PC can be installed into a cabinet or rack. The installation procedures are similar to the panel mounting installation. To do this, please...
AFL2-W15B-H61 flat bezel panel PC and the rack/cabinet into which the AFL2-W15B-H61 is installed. Step 9: Slide the rear chassis of the AFL2-W15B-H61 flat bezel panel PC through the rack/cabinet bracket until the aluminum frame is flush against the front of the bracket ( F igure 3-19).
AFL2-W15B-H61 Step 5: Install the covers into the rack mounting bracket. Each mounting bracket includes two side covers and one top cover ( F igure 3-20 9 1 4 H Figure 3-20: Secure the Rack/Cabinet Bracket Step 6: Slide the flat bezel panel PC with the attached rack/cabinet bracket into a rack or cabinet ( F igure 3-21).
9 1 6 H 3.12.4 Arm Mounting The AFL2-W15B-H61 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 100mm interface pad. To mount the AFL2-W15B-H61 on an arm, please follow the steps below. Step 1: The arm is a separately purchased item.
AFL2-W15B-H61 Figure 3-22: Arm Mounting Retention Screw Holes Step 4: Secure the AFL2-W15B-H61 to the interface pad by inserting four retention screws through the mounting arm interface pad and into the AFL2-W15B-H61. S t e p 0 : Figure 3-23: Arm Mounting (ARM-11-RS)
To mount the AFL2-W15B-H61 using the stand mounting kit, please follow the steps below. Step 1: Locate the screw holes on the rear of the AFL2-W15B-H61. This is where the bracket will be attached. Step 2: Align the bracket with the screw holes.
3.13.1 Audio Connection The audio jacks on the external audio connector enable the AFL2-W15B-H61 to be connected to a stereo sound setup. To install the audio devices, follow the steps below. Step 1: Identify the audio plugs.
3.13.2 HDMI Device Connection The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen. To connect the HDMI cable to the AFL2-W15B-H61, follow the steps below. Step 1: Locate the HDMI connector.
Locate the RJ-45 connectors. The location of the LAN connector is shown in Chapter 1. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the AFL2-W15B-H61. See F igure 3-27. 9 1 8 H Page 43...
AFL2-W15B-H61. 3.13.4.1 DB-9 Serial Port Connection Follow the steps below to connect a serial device to the DB-9 connector of the AFL2-W15B-H61 panel PC. Step 1: Locate the DB-9 connector. The locations of the DB-9 connectors are shown in Chapter 1.
3.13.4.2 RJ-45 Serial Port Connection Follow the steps below to connect a serial device to the RJ-45 serial port connector of the AFL2-W15B-H61 panel PC. Step 1: Locate the RJ-45 serial port. The location of the RJ-45 serial port is shown in Chapter 1.
The AFL2-W15B-H61 has a type K thermocouple connector on the bottom panel. The type K connector is connected to a type K temperature sensor cable, which can be found in the packing list. To connect a type K temperature sensor cable to the AFL2-W15B-H61, please follow the steps below.
User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device. There are three USB 2.0 connectors and two USB 3.0 connectors on the AFL2-W15B-H61. To connect a USB device, please follow the instructions below. Step 1: Locate the USB connectors.
Step 0: 3.13.7 VGA Monitor Connection The AFL2-W15B-H61 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the AFL2-W15B-H61, please follow the instructions below.
AFL2-W15B-H61 4.1 Introduction A licensed copy of the BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.
AFL2-W15B-H61 F2 key Load previous values. F3 key Load optimized defaults F4 key Save changes and Exit BIOS Esc key Main Menu – Quit and do not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu --...
AFL2-W15B-H61 4.2 Main The Main BIOS menu ( B IOS Menu 1) appears when the BIOS Setup program is entered. 8 6 4 H 9 2 5 H The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Page 70
AFL2-W15B-H61 iWDD Version The iWDD Version displays the current iWDD version. The fields in iWDD Version cannot be changed. Memory Information The Memory Information lists a brief summary of the on-board memory. The fields in Memory Information cannot be changed.
↑ ↓: Select Item > F81216 Super IO Configuration > H/M Monitor Enter Select > Serial Port Console Redirection +/-: Change Opt. > iEi Feature General Help Previous Values Optimized Defaults Save & Exit ESC: Exit Version 2.11.1210. Copyright (C) 2011 American Megatrends, Inc.
AFL2-W15B-H61 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI sleep state the system ACPI Sleep State [S1 (CPU Stop Clock)] will enter, when the SUSPEND button is pressed. ---------------------- : Select Screen ↑...
AFL2-W15B-H61 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the dat::hr::min::sec specified ---------------------- : Select Screen ↑ ↓: Select Item...
AFL2-W15B-H61 4.3.3 Trusted Computing Use the Trusted Computing menu ( B IOS Menu 5) to configure settings related to the 9 2 9 H Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
AFL2-W15B-H61 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Socket specific CPU Information > CPU Information ---------------------- Hyper-threading [Enabled] Intel Virtualization Technology [Disabled] : Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
AFL2-W15B-H61 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Socket 0 CPU Information Intel(R) Core(TM) i3-2100T CPU @ 2.50GHz CPU Signature 206a7 ---------------------- Microcode Patch Max CPU Speed 2500 MHz Min CPU Speed 1600 MHz : Select Screen ↑...
AFL2-W15B-H61 4.3.5 SATA Configuration Use the SATA Configuration menu ( B IOS Menu 8) to change and/or set the 9 3 3 H configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
AFL2-W15B-H61 Compatible Configures the Serial-ATA controller to be in compatible EFAULT mode. In this mode, a SATA channel will replace one of the IDE channels. Serial-ATA Controller 1 [Enhanced] Use the Serial-ATA Controller 1 option to configure the Serial-ATA controller mode when the SATA mode is set to IDE Mode.
AFL2-W15B-H61 4.3.7 USB Configuration Use the USB Configuration menu ( B IOS Menu 10) to read USB configuration 9 3 5 H information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration...
AFL2-W15B-H61 keyboard can control the system even when there is no USB driver loaded onto the system. Enabled Legacy USB support enabled EFAULT Disabled Legacy USB support disabled Auto Legacy USB support disabled if no USB devices are connected 4.3.8 F81216 Super IO Configuration...
AFL2-W15B-H61 4.3.8.1 Serial Port n Configuration Use the Serial Port n Configuration menu ( B IOS Menu 12) to configure the serial port n. 9 3 7 H Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port 1 Configuration...
Page 82
AFL2-W15B-H61 IO=3F8h; IRQ=3, Serial Port I/O port address is 3F8h and the 4,5,6,7,10,11,12 interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12 Serial Port I/O port address is 2F8h and the IO=2F8h; IRQ=3, interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12 4,5,6,7,10,11,12 IO=3E8h;...
Page 83
AFL2-W15B-H61 IO=2E8h; IRQ=3, Serial Port I/O port address is 2E8h and the 4,5,6,7,10,11,12 interrupt address is IRQ3, 4, 5, 6, 7, 10, 11, 12 4.3.8.1.3 Serial Port 3 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
AFL2-W15B-H61 Device Mode [RS422] Use the Device Mode option to select the serial port mode. Enables serial port RS-422 support. RS422 EFAULT RS485 Enables serial port RS-485 support. 4.3.9 H/W Monitor The H/W Monitor menu ( B IOS Menu 13) shows the operating temperature, fan speeds 9 3 8 H and system voltages.
Page 85
AFL2-W15B-H61 Fan Speeds: CPU Fan Speed Fanless Temp. Overwrite Control [Enabled] Use the Fanless Temp. Overwrite Control BIOS option to enable or disable Temperature of Fanless configuration. Disabled Temperature of Fanless option can not be configured. Temperature of Fanless option can be configured.
Page 86
AFL2-W15B-H61 16 C When the environment temperature is lower than 16 C, the fan will be switched off. When the environment temperature is lower than 20 C, 20 C the fan will be switched off. 24 C When the environment temperature is lower than 24 C, the fan will be switched off.
AFL2-W15B-H61 4.4 iEi Feature Use the iEi Feature menu ( B IOS Menu 15) to configure the auto recovery function. 9 4 0 H Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function...
AFL2-W15B-H61 Disabled microSD card slot is disabled EFAULT microSD card slot is enabled Enabled 4.5 Chipset Use the Chipset menu ( B IOS Menu 16) to access the North Bridge, South Bridge, 9 4 1 H Integrated Graphics, and ME Subsystem configuration menus.
AFL2-W15B-H61 4.5.1 Northbridge Configuration Use the North Bridge menu ( B IOS Menu 17) to configure the Northbridge chipset. 9 4 2 H Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Memory Information Select which graphics controller to use as the...
AFL2-W15B-H61 32 MB of memory used by internal graphics device 64 MB of memory used by internal graphics device 128M 128 MB of memory used by internal graphics device 256M 256 MB of memory used by internal graphics EFAULT device...
Page 92
AFL2-W15B-H61 Power Off The system remains turned off The system turns on Power On Last State The system returns to its previous state. If it was on, it EFAULT turns itself on. If it was off, it remains off. Power Saving Function [Disabled] Use the Power Saving Function BIOS option to enable or disable the power saving function.
Page 93
AFL2-W15B-H61 RFID Function [Enabled] Use the RFID Function option to enable or disable the RFID function. RFID function disabled Disabled Enabled RFID function enabled EFAULT Auto Dimming Support [Disabled] Use the Auto Dimming Support option to enable or disable the auto dimming function.
Page 94
AFL2-W15B-H61 Enabled Enables PCIe LAN PXE Boot option PCIe LAN Controller [Enabled] Use the PCIe LAN Controller option to enable or disable the PCI Express LAN controller. The onboard PCIe LAN controller is disabled Disabled Enabled The onboard PCIe LAN controller is enabled EFAULT PCIe USB 3.0 Controller [Enabled]...
AFL2-W15B-H61 IGD - Boot Type [AUTO] Use the IGD - Boot Type option to select the display device used by the system when it boots. For dual display support, select “Auto.” Configuration options are listed below. AUTO EFAULT LVDS HDMI 4.5.4 ME Subsystem...
AFL2-W15B-H61 Enter Enables user to enter MEBx setup MEBx Setup Unconfigure AMT/ME [Enabled] Use the Unconfigure AMT/ME option to perform AMT/ME unconfigure without password operation. Disable AMT/ME unconfigure Disabled Enabled Enable AMT/ME unconfigure EFAULT 4.6 Boot Use the Boot menu ( B IOS Menu 21) to configure system boot options.
Page 98
AFL2-W15B-H61 Allows the Number Lock on the keyboard to be EFAULT enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.
AFL2-W15B-H61 4.7 Security Use the Security menu ( B IOS Menu 22) to set system and user passwords. 9 4 7 H Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit...
AFL2-W15B-H61 4.8 Save & Exit Use the Save & Exit menu ( B IOS Menu 23) to load default BIOS values, optimal failsafe 9 4 8 H values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
Page 101
AFL2-W15B-H61 Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system:...
AFL2-W15B-H61 Figure 5-1: Drivers 5.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 5 .2) 9 4 9 H Step 2: Click “Chipset.” Step 3: Locate the setup file and double click on it.
AFL2-W15B-H61 Figure 5-2: Chipset Driver Screen Step 5: When the setup files are completely extracted the Welcome Screen in F igure 9 5 1 H 5-3 appears. Step 6: Click Next to continue. Figure 5-3: Chipset Driver Welcome Screen Step 7: The license agreement in F igure 5-4 appears.
AFL2-W15B-H61 Step 8: Read the License Agreement. Step 9: Click Yes to continue. Figure 5-4: Chipset Driver License Agreement Step 10: The Read Me file in F igure 5-5 appears. 9 5 3 H Step 11: Click Next to continue.
AFL2-W15B-H61 Figure 5-5: Chipset Driver Read Me File Step 12: Setup Operations are performed as shown in F igure 5-6. 9 5 4 H Step 13: Once the Setup Operations are complete, click Next to continue. Figure 5-6: Chipset Driver Setup Operations...
AFL2-W15B-H61 Step 15: Select “Yes, I want to restart this computer now” and click Finish.Step 0: Figure 5-7: Chipset Driver Installation Finish Screen 5.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 5 .2)
AFL2-W15B-H61 Figure 5-8: Graphics Driver Read Me File Step 6: The installation files are extracted. See F igure 5-9. 9 5 8 H Step 7: Click Next to continue. Figure 5-9: Graphics Driver Setup Files Extracted Step 8: The Welcome Screen in F igure 5-10 appears.
AFL2-W15B-H61 Figure 5-10: Graphics Driver Welcome Screen Step 10: The License Agreement in F igure 5-11 appears. 9 6 0 H Step 11: Click Yes to accept the agreement and continue. Figure 5-11: Graphics Driver License Agreement Step 12: The Read Me file in F igure 5-12 appears.
AFL2-W15B-H61 Figure 5-12: Graphics Driver Read Me File Step 14: Setup Operations are performed as shown in F igure 5-13. 9 6 2 H Step 15: Once the Setup Operations are complete, click Next to continue. Figure 5-13: Graphics Driver Setup Operations...
AFL2-W15B-H61 Figure 5-14: Graphics Driver Installation Finish Screen 5.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Access the driver list. (See Section 5 .2) 9 6 4 H Step 2: Click “LAN” and select the folder which corresponds to the operating system.
AFL2-W15B-H61 Figure 5-15: LAN Driver Welcome Screen Step 5: Click Next to continue. Step 6: The Ready to Install the Program Screen in F igure 5-16 appears. 9 6 6 H Step 7: Click Install to proceed with the installation.
AFL2-W15B-H61 Figure 5-17: LAN Driver Setup Status Screen Step 10: When the driver installation is complete, the screen in F igure 5-18 appears. 9 6 8 H Step 11: Click Finish to exit. Figure 5-18: LAN Driver Installation Complete 5.6 Audio Driver Installation To install the audio driver, please do the following.
AFL2-W15B-H61 Step 2: Click “Audio” and select the folder which corresponds to your operating system. Step 3: Double click the setup file. Step 4: The Audio Driver Welcome Screen in F igure 5-19 appears. 9 7 0 H Step 5: Click Next to continue.
AFL2-W15B-H61 Figure 5-20: Audio Driver Installation Step 7: When the installation is complete, the screen in F igure 5-21 appears. 9 7 2 H Step 8: Select “Yes, I want to restart my computer now” and click Finish. Step 0:...
AFL2-W15B-H61 5.7 Touch Screen Driver To install the touch panel software driver, please follow the steps below. Step 1: Access the driver list. (See Section 5 .2) 9 7 3 H Step 2: Click “Touch Screen.” Step 3: Locate the setup file and double click on it.
AFL2-W15B-H61 Figure 5-23: Touch Screen Driver License Agreement Step 8: Browse for an install location or use the one suggested ( F igure 5-24). 9 7 6 H Step 9: Click I to continue. NSTALL Figure 5-24: Touch Screen Driver Choose Install Location...
AFL2-W15B-H61 Step 11: Click N to continue. Figure 5-25: Touch Screen Driver Installation Screen Step 12: When the installation is complete, click F to exit setup. ( F igure 5-26). INISH 9 7 8 H Figure 5-26: Touch Screen Driver Update Complete...
AFL2-W15B-H61 5.7.1 Calibrating the Touch Screen To calibrate the touch screen cursor with the motion of the touch screen pen (or finger), please follow the steps below: Step 1: Make sure the touch screen driver is properly installed. Step 2: Locate the PenMount Monitor icon in the bottom right corner of the screen.
AFL2-W15B-H61 Figure 5-29: Configuration Screen Step 6: Double click the PenMount 9000 icon as shown in F igure 5-29. 9 8 2 H Step 7: The calibration initiation screen in F igure 5-30 appears. 9 8 3 H Step 8: Select the Standard Calibration button as shown in F igure 5-30.
AFL2-W15B-H61 Figure 5-31: Calibration Screen Step 10: Follow the instructions. The user is asked touch the screen at five specified points after which the screen is calibrated. Step 0: 5.8 Wi-Fi Driver Installation To install the wireless LAN driver, please follow the steps below.
AFL2-W15B-H61 Step 4: Accept the conditions of the license agreement and click NEXT to continue. Step 5: The Setup Type screen in F igure 5-33 appears. 9 8 8 H Figure 5-33: Setup Type Step 6: Select “Install driver and Ralink WLAN Utility” and click NEXT to continue.
AFL2-W15B-H61 Figure 5-34: Configuration Tool Select “Ralink Configuration Tool”and click NEXT to continue. Step 8: Step 9: The Ready to Install the Program screen in F igure 5-35 appears. 9 9 0 H Figure 5-35: Ready to Install the Program Step 10: Click Install to proceed with the installation.
AFL2-W15B-H61 Step 11: The Setup Status screen in F igure 5-36 appears and displays the progress of 9 9 1 H the installation. Figure 5-36: Setup Status Step 12: When the driver installation is complete, the screen in F igure 5-37 appears.
AFL2-W15B-H61 Figure 5-39: USB 3.0 Driver License Agreement Step 8: Click N to continue. Figure 5-40: USB 3.0 Driver Installation Step 9: The Install screen appears and displays the progress of the installation. Step 10: When the installation is complete, click Finish to exit setup. ( F igure 5-41).
AFL2-W15B-H61 6.1 IEI Cooling Management Console (iCMC) The iCMC system cooling management console tracks system and CPU temperatures, frequency, cooling fan speeds, and allows users to configure light fanless settings. The iCMC quickly captures and reports system conditions to ensure operators can prevent system damage.
AFL2-W15B-H61 Step 4: Select a folder for Cooling Management Console installation in F igure 6-2. Click 9 9 7 H Next to continue. Figure 6-2: Select Installation Folder Step 5: The following screen appears. Click Next to confirm the installation.
AFL2-W15B-H61 Step 7: When the Cooling Management Console is successfully installed, the following window appears. Click Close to exit. Figure 6-4: Installation Complete Step 8: The confirmation screen offers the option of restarting the system now or later. For the settings to take effect, the system must be restarted. Click Yes to restart the system.
AFL2-W15B-H61 Figure 6-6: Cooling Management Console Icon 6.2 iCMC Overview F igure 6-7 shows the iCMC interface. The iCMC interface is consisted of two panels: 9 9 8 H information panel (left) and chart panel (right). The chart panel can be hidden by selecting Chart visible option to “Off”.
AFL2-W15B-H61 Figure 6-8: iCMC Information Panel Temperature The current CPU temperature. System 1 The current system temperature. System 2 The current system temperature. Environment 1 The current environment temperature detected by the temperature sensor on the system. Environment 2 The current environment temperature detected by the temperature sensor on the system.
AFL2-W15B-H61 The system fan speed. “0” indicates the fan is off. System Info CPU Frequency The CPU frequency parameters. CPU Loading The CPU loading parameters. CPU Type The brand name of the CPU being used in the system. Light Fanless Settings...
AFL2-W15B-H61 6.2.2 Chart Panel F igure 6-9 shows the chart panel interface. The line chart is used to visualize the system 1 0 0 2 H data listed in the information panel. The following information is displayed in different color...
AFL2-W15B-H61 The user can adjust the time interval between sampling by selecting the options in the Sampling drop down menu (see F igure 6-10). The x-axis of the line chart (Time in 1 0 0 3 H seconds) will change according to the adjustment.
AFL2-W15B-H61 7.1 System Maintenance Introduction If the components of the AFL2-W15B-H61 fail they must be replaced. Components that can be replaced include: SO-DIMM module WLAN module Please contact the system reseller or vendor to purchase the replacement parts. Back cover removal instructions for the AFL2-W15B-H61 are described below.
Over-tightening back cover screws will crack the plastic frame. Maximum torque for cover screws is 5 kg-cm (0.36 lb-ft/0.49 Nm). To access the AFL2-W15B-H61 internally the back cover must be removed. To remove the back cover, please follow the steps below.
AFL2-W15B-H61 Step 3: Remove a total of ten (10) retention screws from the back cover ( F igure 7-1). 1 0 0 7 H Figure 7-1: Back Cover Retention Screws Step 4: Carefully separate the back cover from the chassis and lift the cover clear of the...
AFL2-W15B-H61 Figure 7-2: Internal Cover Retention Screws Step 2: Lift the aluminum cover off the AFL2-W15B-H61. Step 3: The internal parts will all be viewable. Figure 7-3: Internal Components 7.5 Replacing Components 7.5.1 Memory Module Replacement The flat bezel panel PC is preinstalled with two 2.0 GB DDR3 memory module. If the memory module fails, follow the instructions below to replace the memory module.
AFL2-W15B-H61 Step 1: Follow all anti-static procedures. See Section 7 .2. 1 0 0 9 H Step 2: Turn off the power. See Section 7 .3. 1 0 1 0 H Step 3: Remove the back cover. See Section 7 .4.1 above.
Replace the back cover and secure it using ten (10) previously removed retention screws. Step 0: 7.5.2 WLAN Card Replacement The AFL2-W15B-H61 has one WLAN card slot. To replace the WLAN card, follow the instructions below. Step 1: Follow all anti-static procedures. See Section 7 .2.
AFL2-W15B-H61 Figure 7-6: Releasing the WLAN Card Step 8: Grasp the WLAN card by the edges and carefully pull it out of the socket ( F igure 1 0 2 0 H 7-7). Figure 7-7: Removing the WLAN card Step 9:...
AFL2-W15B-H61 Figure 7-8: Attaching the Antennas Step 12: Replace the internal aluminum cover and secure it to the chassis using six (6) retention screws. Step 13: Replace the back cover and secure it using ten (10) previously removed retention screws.
AFL2-W15B-H61 8.1 Peripheral Interface Connectors The AFL2-W15B-H61 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in F igure 8-1. 1 0 2 2 H The Pin 1 locations of the on-board connectors are also indicated in the diagram below.
AFL2-W15B-H61 8.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the AFL2MB-15A. Pinouts of these connectors can be found in the following sections.
AFL2-W15B-H61 8.2.14 Mini USB Connector (MINUSB1) PIN NO. DESCRIPTION -DATA8 +DATA8 3VCC Table 8-15: Mini USB Connector (MINUSB1) Pinouts 8.2.15 Mini USB Connector (MINUSB2) PIN NO. DESCRIPTION -DATA4 +DATA4 Table 8-16: Mini USB Connector (MINUSB2) Pinouts 8.2.16 Power Button Connector (PW_BT1) PIN NO.
AFL2-W15B-H61 8.2.17 RFID USB Connector (RFIDUSB1) PIN NO. DESCRIPTION -DATA5 +DATA5 Table 8-18: RFID USB Connector (RFID_USB1) Pinouts 8.2.18 SATA Connector (SATA1) PIN NO. DESCRIPTION Table 8-19: SATA Connector (SATA1) Pinouts 8.2.19 SATA Power Connector (CN8) PIN NO. DESCRIPTION +V5S...
Page 166
Do not apply voltage levels that exceed the specified voltage range. Doing so may cause fire and/or an electrical shock. Electric shocks can occur if the AFL2-W15B-H61 chassis is opened when the AFL2-W15B-H61 is running. Do not drop or insert any objects into the ventilation openings of the AFL2-W15B-H61.
Page 167
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AFL2-W15B-H61. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the AFL2-W15B-H61 is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to.
Page 168
Please follow the national guidelines for electrical and electronic product disposal. A.2 Maintenance and Cleaning Precautions When maintaining or cleaning the AFL2-W15B-H61, please follow the guidelines below. A.2.1 Maintenance and Cleaning Prior to cleaning any part or component of the AFL2-W15B-H61, please read the details below. Page 151...
In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the AFL2-W15B-H61. Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the AFL2-W15B-H61.
AFL2-W15B-H61 Appendix BIOS Menu Options Page 153...
Page 171
AFL2-W15B-H61 BIOS Information ......................... 4 0 6 H 1 0 2 4 H iWDD Vendor ........................4 0 7 H 1 0 2 5 H iWDD Version ........................4 0 8 H 1 0 2 6 H ...
Page 172
AFL2-W15B-H61 DMIC Function [Enabled] ....................4 4 0 H 1 0 5 8 H BT Function [Enabled]......................4 4 1 H 1 0 5 9 H RFID Function [Enabled] ..................... 4 4 2 H 1 0 6 0 H ...
Page 173
AFL2-W15B-H61 Appendix One Key Recovery Page 156...
AFL2-W15B-H61 C.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
Page 175
1 0 9 0 H C.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware. To create the system backup, the main storage device must be split into two partitions (three partitions for Linux).
Page 176
AFL2-W15B-H61 partitions. Please take the following table as a reference when calculating the size of the partition. OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB Windows® XPE 776 MB 560 MB Windows® CE 6.0 36 MB...
Page 178
AFL2-W15B-H61 The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section C .3.
AFL2-W15B-H61 Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below.
AFL2-W15B-H61 Figure C-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
Page 182
AFL2-W15B-H61 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.S t e p 0 : C.2.3 Install Operating System, Drivers and Applications...
AFL2-W15B-H61 C.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please...
AFL2-W15B-H61 Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C .2.2 is hidden and the recovery tool is saved in this partition.
AFL2-W15B-H61 C.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system.
AFL2-W15B-H61 Figure C-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below ( F igure C-13). 1 1 0 3 H Figure C-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in F igure C-14.
F igure C-16). Click Save. The factory default image will then be saved in the 1 1 0 6 H selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO. Page 170...
AFL2-W15B-H61 Figure C-16: File Name to Copy Image to Step 8: When the Compress Image screen in F igure C-17 prompts, click High to make 1 1 0 7 H the image file smaller. Figure C-17: Compress Image Page 171...
AFL2-W15B-H61 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. S t e p 0 : Figure C-21: Press Any Key to Continue C.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes.
AFL2-W15B-H61 Step 1: Follow the steps described in Section C .2.1 ~ Section C .2.3 to setup BIOS, 1 1 1 0 H 1 1 1 1 H create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
AFL2-W15B-H61 Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4>...
AFL2-W15B-H61 Figure C-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES).
AFL2-W15B-H61 Step 8: The Symantec Ghost starts to create the factory default image ( F igure C-28). 1 1 1 4 H Figure C-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system.
AFL2-W15B-H61 Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure C-30: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow...
AFL2-W15B-H61 recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure C-31: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified.
AFL2-W15B-H61 Step 7: The recovery tool menu appears. ( F igure C-33) 1 1 1 8 H Figure C-33: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 Step 12 described in Section C .2.5 to create a factory default image.
AFL2-W15B-H61 Figure C-34: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section C .2.5. 1 1 2 1 H 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition.
Type <1> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure C-35: Restore Factory Default Step 3: The screen shown in F igure C-36 appears when completed.
AFL2-W15B-H61 C.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition.
AFL2-W15B-H61 C.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO).
AFL2-W15B-H61 C.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <Enter> in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually.
Page 204
AFL2-W15B-H61 C.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
Page 205
AFL2-W15B-H61 C.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf...
Page 206
AFL2-W15B-H61 filename “pxelinux.0”; C.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file.
Page 207
AFL2-W15B-H61 Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin..(as shown below) #vi /etc/xinetd.d/tftp C.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key...
Page 208
Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.gho /image WARNING: The file name of the factory default image must be iei.gho. Step 3: Confirm the operating system default settings: smb.conf. #vi /etc/samba/smb.conf Page 191...
Page 209
AFL2-W15B-H61 Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname...
Figure C-42: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled...
Page 211
AFL2-W15B-H61 MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image.
Page 212
AFL2-W15B-H61 NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. C.7 Other Information C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller...
Page 213
AFL2-W15B-H61 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Page 196...
Page 214
AFL2-W15B-H61 Step 6: In the following window, select a SATA controller mode used in the system. Then press <Enter>. The user can now start using the SATA HDD. Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu.
Page 216
AFL2-W15B-H61 D.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Page 217
AFL2-W15B-H61 Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply Assemblies Battery...