D-Link xStack DGS-3400 Series Cli Reference Manual page 71

xStack
Command
create access_profile
delete access_profile
config access_profile
config flow_meter
show flow_meter
config time_range
show time_range
Each command is listed, in detail, in the following sections.
create access_profile
Purpose
®
DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch CLI Manual
Parameters
[ethernet {vlan | source_mac <macmask 000000000000-ffffffffffff> |
destination_mac <macmask 000000000000-ffffffffffff> | 802.1p | ethernet_type} |
ip {vlan | source_ip_mask <netmask> | destination_ip_mask <netmask> | dscp |
[icmp {type | code} | igmp {type} | tcp {src_port_mask <hex 0x0-0xffff> |
dst_port_mask <hex 0x0-0xffff> | flag_mask [ all | {urg | ack | psh | rst | syn |
fin}]} | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-0xffff>} |
protocol_id_mask <hex 0x0-0xff> {user_define_mask <hex 0x0-0xffffffff>}]}|
packet_content_mask { offset_chunk_1 <value 0-31> <hex 0x0-0xffffffff> |
offset_chunk_2 <value 0-31> <hex 0x0-0xffffffff> | offset_chunk_3 <value 0-31>
<hex 0x0-0xffffffff> | offset_chunk_4 <value 0-31> <hex 0x0-0xffffffff>}| ipv6
{class | flowlabel | source_ipv6_mask <ipv6mask> | destination_ipv6_mask
<ipv6mask> | [ tcp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-
0xffff>} | udp {src_port_mask <hex 0x0-0xffff> | dst_port_mask <hex 0x0-
0xffff>}]}] profile_id <value 1-6>
[profile_id <value 1-6> |all]
profile_id <value 1-6> [add access_id [auto_assign | <value 1-128>] [ethernet
{vlan <vlan_name 32> | source_mac <macaddr 000000000000-ffffffffffff> |
destination_mac <macaddr 000000000000-ffffffffffff> | 802.1p <value 0-7> |
ethernet_type <hex 0x0-0xffff>} port [<portlist> | all] [permit {priority <value 0-7>
{replace_priority} | rx_rate [no_limit | <value 1-156249>] | replace_dscp <value
0-63> | counter [enable | disable]} | mirror {group_id <value 1-4>} | deny] | ip
{vlan <vlan_name 32> | source_ip <ipaddr> | destination_ip <ipaddr> | dscp
<value 0-63> | [icmp {type <value 0-255> | code <value 0-255>} | igmp {type
<value 0-255>} | tcp {src_port <value 0-65535> | dst_port <value 0-65535> | urg
| ack | psh | rst | syn | fin} | udp {src_port <value 0-65535> | dst_port <value 0-
65535>} | protocol_id <value 0 - 255> {user_define <hex 0x0-0xffffffff>}]} port
[<portlist> | all] [permit {priority <value 0-7> {replace_priority} | rx_rate [ no_limit |
<value 1-156249>] | replace_dscp <value 0-63> | counter [enable | disable]} |
mirror {group_id <value 1-4>} | deny] | packet_content {offset_chunk_1 <hex
0x0-0xffffffff> | offset_chunk_2 <hex 0x0-0xffffffff> | offset_chunk_3 <hex 0x0-
0xffffffff> | offset_chunk_4 <hex 0x0-0xffffffff>} port [<portlist> | all] [permit
{priority <value 0-7> {replace_priority} | rx_rate [no_limit | <value 1-156249>] |
replace_dscp <value 0-63> | counter [enable | disable]} | mirror {group_id <value
1-4>} | deny] | ipv6 {class <value 0-255> | flowlabel <hex 0x0-0xfffff> |
source_ipv6 <ipv6addr> | destination_ipv6 <ipv6addr> | [ tcp {src_port <value 0-
65535> | dst_port <value 0-65535>} | udp {src_port <value 0-65535> | dst_port
<value 0-65535>}]} port [<portlist> | all] [permit {priority <value 0-7>
{replace_priority} | rx_rate [no_limit | <value 1-156249>] | counter [enable |
disable]} | mirror {group_id <value 1-4>} | deny]]{time_range <range_name 32>}
| delete access_id <value 1-128>]
profile_id <value 1-6> access_id <value 1-128>[ [ tr_tcm cir <value 0-156249>
{cbs <value 0-16384>} pir <value 0-156249> {pbs <value 0-16384>} | sr_tcm
cir <value 0-156249> cbs <value 0-16384> ebs <value 0-16384> ] {conform
[permit | replace_dscp <value 0-63>] {counter [enable |disable]}} exceed [permit
| replace_dscp <value 0-63> | drop] {counter [enable |disable]} violate [permit |
replace_dscp <value 0-63> | drop] {counter [enable |disable]} | delete]
{profile_id <value 1-6> {access_id <value 1-128>}}
<range_name 32> [hours start_time <time hh:mm:ss> end_time <time
hh:mm:ss> weekdays <daylist> |delete]
Used to create access list rules.
67