AudioCodes Mediant 1000 User Manual page 234

Table 6-8: ISDN and CAS Interworking-Related Parameters (continues on pages 233 to 236)
ini File Field Name
Web Parameter Name
DefaultCauseMapISDN2I
P
RemoveCLIWhenRestrict
ed
ScreeningInd2ISDN
ProgressIndicator2ISDN_
ID
ProgressIndicator2IP
PIForDisconnectMsg_ID
LocalISDNRBSource_ID
PSTNAlertTimeout
EnableTransferCap
ISDNTransferCapability_I
D
SendISDNTransferOnCon
nect
EnableUUITel2IP
H.323 User's Manual
Valid Range and Description
Defines a single default ISDN Release Cause that is used (in ISDN to IP calls)
instead of all received release causes except when the following Q.931 cause
values are received: Normal Call Clearing (16), User Busy (17), No User
Responding (18) or No Answer from User (19).
The range is valid Q.931 release causes (0 to 127). The default value is 0
(indicates that the parameter is not configured - static mapping is used).
For a description of this parameter, refer to
For a description of this parameter, refer to
ID = Trunk number (0-7).
0, 1 or 8
-1 = Not configured (default).
If set to '0' PI is not sent to ISDN
If set to '1' or '8' the PI value is sent to PSTN in Q.931/Proceeding and Alerting
messages.
If not configured, the PI in ISDN messages is set according to the 'Play Ringback
to Tel' parameter.
Usually if PI = 1 or 8, the PSTN/PBX cuts through the audio channel without
playing local Ringback tone, enabling the originating party to hear remote Call
Progress Tones or network announcements
For a description of this parameter, refer to
ID = Trunk number.
Defines the gateway's behavior when a Disconnect message is received from the
ISDN before a Connect message was received.
-1 (Not configured) = Sends an Alert message according to the received PI in the
ISDN Disconnect message. If PI = 1 or 8, the gateway sends an Alert message,
enabling the PSTN to play a voice announcement to the IP side. If there isn't a PI
in the Disconnect message, the call is released (default).
0 = Do not send an Alert message to IP. The call is released.
1, 8 = Sets the PI in the Alert message to the specified value (overwrites the PI
that is received in the Disconnect message).
ID = Trunk number.
Determines whether Ringback tone is played to the ISDN by the PBX / PSTN or
by the gateway.
0 = PBX / PSTN (default).
1 = Gateway.
This parameter is applicable to ISDN protocols. It is used simultaneously with the
parameter 'PlayRBTone2Trunk'.
For a description of this parameter, refer to
For a description of this parameter, refer to
ID = Trunk number.
Defines the IP ISDN Transfer Capability of the Bearer Capability IE in ISDN
Setup messages.
-1 = Use H.323 transfer capability (default).
To enable this option the parameter 'EnableTransferCapability' must be set to '1'.
0 = Audio 3.1.
1 = Speech.
2 = Data.
Note: If the parameter 'ISDNTransferCapability' is set to 0, 1 or 2, the parameter
'EnableTransferCapability' is ignored.
For a description of this parameter, refer to
For a description of this parameter, refer to
234
Mediant 1000
Table 5-21 on page 126.
Table 5-21 on page 126.
Table 5-7 on page 80.
Table 5-21 on page 126.
Table 5-21 on page 126.
Table 5-21 on page 126.
Table 5-21 on page 126.
Document #: LTRT-83401