Ag --Pgcreate- Pgid "N_Port1 [;N_Port2; Ag [--Pgadd | --Pgdel] Pgid "N_Port1 [; N_Port2; Ag [--Pgmapadd | --Pgmapdel] Pgid "F_Port1 [; F_Port2; Ag [ --Pgsetmodes | Pgdelmodes ] Pgid "Mfnm;Lb - Brocade Communications Systems Brocade 8/12c Command Reference Manual

2
ag
pgshow [pgid]
--
--pgcreate- pgid "N_Port1 [; N_Port2;...]" [-n pgname] [-m "lb; mfnm"]
--pgadd pgid "N_Port1 [; N_Port2;...]"
--pgdel pgid "N_Port1 [; N_Port2;...]"
--pgrename pgid newname
--pgremove pgid
--pgmapadd pgid "F_Port1[;F_Port2;...]"
--pgmapdel pgid "F_Port1[;F_Port2;...]"
--pgsetmodes pgid "lb;mfnm"
24
Displays the Port Group configuration. The port grouping feature supports
specifying a set of N_Ports to be included in the Port Group (PG) Policy. The
factory default PG is "pg0", which includes all N_Ports. The default PG cannot
be removed or renamed.
Creates a port group with the ID pgid and a specified list of N_Ports to be
included in the policy. The list must be enclosed in quotation marks. Ports
must be separated by semicolons. The Port Group ID must not exceed 64
characters. Optionally specify a name for the port group and a mode. Modes
are by default disabled. For an explanation of mode values, refer to
--pgsetmodes.
Adds one or more N_Ports to the specified port group. The port list must be
enclosed in quotation marks. Ports must be separated by semicolons.
Deletes one or more N_Ports from the specified port group. Deleted ports are
added to the default port group "pg0". The port list must be enclosed in
quotation marks. Ports must be separated by semicolons.
Replaces the name of an existing port group with the specified new name.
The port group ID must not exceed 64 characters.
Deletes the specified port group. The N_Ports in the port group that was
deleted are moved to the default port group, which is pgid 0.
Maps the specified F_Ports to the PG identified by the pgid. Upon execution,
the system identifies the least loaded N_Port in the port group and maps the
F_Ports to that N_Port. The port list must be enclosed in double quotation
marks. Ports must be separated by semicolons. Login balancing (LB) mode
must be enabled on the port group for this command to succeed. Use ag
--pgsetmodes to enable LB mode.
Removes one or more F_Ports that are part of the port group identified by the
pgid from their mapping to a corresponding N_Port. The port list must be
enclosed in double quotation marks. Ports must be separated by semicolons.
Login balancing (LB) mode must be enabled on the port group for this
command to succeed. Use ag --pgsetmodes to enable LB mode.
Sets the APC modes for the specified port group. The mode list must be
enclosed in double quotation marks and the modes must be separated by a
semicolon. Alternately you can set the modes at the time when you create the
port group with the pgcreate command. The following modes are supported:
lb Specifies the login balancing mode for the specified port group. If login
balancing mode is enabled and an F_Port goes offline, logins in the port
group are redistributed among the remaining F_Ports. Similarly, if an N_Port
comes online, port logins in the PG are redistributed to maintain a balanced
N_Port to F_Port ratio. This operation is disruptive. Login balancing mode is
by default disabled in all port groups.
Fabric OS Command Reference
53-1001764-01