Run Codes - Genie GCL-J&H Installation Manual

Run Code Displays
Condition
DISPLAY
Code
0C IDLE > DOWN LIMIT
IDLE > UP LIMIT
0D
IDLE > MID STOP
0E
IDLE > NO LIMIT
0F
OPENING > OPEN BTN
10
OPENING > ONE BTN
11
OPENING > RADIO
12
OPENING > AUX OPEN
13
OPENING > OPEN KEY
14
CLOSING > CLOSE PB
20
CLOSING > ONE BTN
21
CLOSING > RADIO
22
CLOSING > CLOSE KP
24
CLOSING > TCM CLS
2A
2B CLOSING > FDM CLS
HALT > WALL BUTTON
30
HALT > ONE BUTTON
31
HALT > RADIO
32
HALT > AUX. OPEN
33
HALT > KEYPAD KEY
34
HALT > N-O SAFETY
35
HALT > PHOTOCELL
36
HALT > N-C SAFETY
37
HALT > MON. EDGE
38
HALT > DOOR FORCE
39
HALT > LOSS OF C/C
3A
HALT > SHUTDOWN
3B
HALT > DOWN LIMIT
3C
HALT > UP LIMIT
3D
HALT > MID STOP
3E
HALT > MODULE FAIL
3F
REV > OPEN BUTTON
40
REV > ONE BUTTON
41
REV > RADIO
42
REV > AUX OPEN
43
REV > OPEN KEY
44
REV > N-O SAFETY
45
GCL-J&H
Standard Duty Operator
Section 10: Appendix C
Condition Code Description
STANDING BY AT DOWN LIMIT (NOTE: THIS MESSAGE IS DISPLAYED IF BOTH LIMITS ARE ACTIVE)
STANDING BY AT UP LIMIT
STANDING BY AT MID-STOP LIMIT
STANDING BY BETWEEN LIMITS
OPENING FROM OPEN BUTTON
OPENING FROM 1 BUTTON
OPENING FROM RADIO
OPENING FROM AUXILIARY OPEN INPUT
OPENING FROM KEYPAD OPEN KEY
CLOSING FROM CLOSE BUTTON
CLOSING FROM 1 BUTTON
CLOSING FROM RADIO
CLOSING FROM KEYPAD CLOSE KEY
CLOSING FROM TIMER CLOSE MODULE
CLOSING FROM FORE DOOR MODULE
GDO STOPPED BECAUSE STOP OR OPEN BUTTON WAS ACTIVATED, POSSIBLY STARTING A REVERSAL
GDO STOPPED BECAUSE 1 BUTTON WAS ACTIVATED, POSSIBLY STARTING A REVERSAL
GDO STOPPED BECAUSE RADIO INPUT WAS ACTIVATED, STARTING A REVERSAL
GDO STOPPED BECAUSE AUXILIARY OPEN INPUT WAS ACTIVATED, STARTING A REVERSAL
GDO STOPPED BECAUSE KEYPAD STOP OR OPEN KEY WAS ACTIVATED, POSSIBLY STARTING A REVERSAL
GDO STOPPED BECAUSE N-O REVERSING INPUT WAS ACTIVATED, STARTING A REVERSAL
GDO STOPPED BECAUSE PHOTOCELL WAS BLOCKED, STARTING A REVERSAL
GDO STOPPED BECAUSE N-C REVERSING INPUT WAS ACTIVATED, STARTING A REVERSAL
GDO STOPPED BECAUSE MONITORED EDGE SENSOR INPUT WAS ACTIVATED, STARTING A REVERSAL
GDO STOPPED BECAUSE THE FORCE REQUIRED TO OPERATE THE DOOR WAS TOO HIGH, POSSIBLY STARTING A REVERSAL
GDO STOPPED BECAUSE CONSTANT CONTACT ON CONTROL REMOVED BEFORE REACHING A LIMIT, POSSIBLY STARTING A REVERSAL
GDO STOPPED BECAUSE THE GDO DETECTED A FAULT SUCH AS AN OPEN INTERLOCK, OVERHEATED MOTOR, ETC.
GDO STOPPED BECAUSE IT REACHED THE DOWN LIMIT
GDO STOPPED BECAUSE IT REACHED THE UP LIMIT
GDO STOPPED BECAUSE IT REACHED THE MID-STOP LIMIT
GDO STOPPED BECAUSE AN EXPANSION MODULE WAS NOT WORKING PROPERLY
GDO REVERSED BECAUSE THE OPEN BUTTON WAS ACTIVATED
GDO REVERSED BECAUSE THE 1 BUTTON WAS ACTIVATED
GDO REVERSED BECAUSE THE RADIO INPUT WAS ACTIVATED
GDO REVERSED BECAUSE THE AUXILIARY OPEN INPUT WAS ACTIVATED
GDO REVERSED BECAUSE THE KEYPAD OPEN KEY WAS ACTIVATED
GDO REVERSED BECAUSE THE N-O REVERSING INPUT WAS ACTIVATED
www.geniecompany.com
10.10
0 -12