Download  Print this page

Sony BVMF170A Operation Manual Page 10

Professional video monitor.
Hide thumbs

Advertisement

5) DisplayPort, DisplayPort logo and VESA are trademarks or registered
trademarks of Video Electronics Standards Association.
HD frame capture function
The frame of the 3G/HD-SDI input signal is captured and
6)
saved
as a picture file in the "Memory Stick". This is
used to confirm the color tone and picture angle of the
current scene and recorded scene by using the multi display
(Picture&Picture) function.
For the operation, see "Capturing the Picture of the HD
Signal (HD Frame Capture)" on page 93.
6) As the frame of the input signal is captured, the data and marker set by the
monitor is not reflected.
Multi display function
Two kinds of input signals are output on the monitor. Side
by side mode is useful for adjusting the color or comparing
two pictures.
For the operation, see "Displaying Two Signals on One
Screen (Picture&Picture)" on page 91.
Pixel zoom function
As part of the picture is magnified up to 8 times without
scaling processing, this is convenient for confirming a
minute part of the signal.
For the operation, see "Magnifying the Picture (Pixel
Zoom)" on page 92.
Safe area marker and aspect marker functions
The monitor is equipped with two area markers and center
marker as the safe area marker and aspect marker for
confirming the picture angle.
For the operation, see "Displaying the Area Marker or
Aspect Marker" on page 94.
Scan selection/Native scan display function
You can select from under scan (–3%), normal scan (0%)
and over scan (mask of the 5% over scan portion in the
normal scan) for the picture display.
The monitor is equipped with a native scan display
function which maps the pixel of the signal to the panel in
one-to-one mode. You can select the mode from ×1, ×2 or
Aspect Correction to display a signal in native mode. An
SD signal of non-square pixels (the number of H pixels of
the signal system is 720 or 1440) or a 640 × 480 SD signal
of HDMI/DisplayPort video is displayed correctly by
scaling processing of doubling for the V direction and
correct aspect ratio for the H direction, and the picture is
also optimized and displayed by modifying the aperture
coefficient value, filter coefficient value, etc. in Aspect
Correction mode.
For the operation, see "Selecting the Native Scan/Scan
Mode" on page 90.
10
Features
Aspect selectable function
A squeezed and recorded signal is displayed with the
correct angle. You can select from 4:3 and 16:9 aspect
modes.
Remote control function (Ethernet control)
The controller controls up to 32 monitors by the Ethernet
(10BASE-T/100BASE-TX) connection. Up to four
controllers are connected to one monitor in single mode.
You can control individual monitors or monitor groups
simply by entering the monitor ID number or group ID
number. You can also execute the same operation on all
connected monitors, or put all connected monitors into the
same setup and adjustment state.
Time code display function
The time code superimposed on the SDI signal is
displayed.
Closed caption display function
EIA/CEA-608 or EIA/CEA-708 standard closed caption
signals superimposed on the SDI signals are displayed by
installing the optional input adaptor (BKM-244CC).
Audio level meter display function
The audio level of the embedded audio signals
superimposed on the SDI signal is displayed by installing
the optional input adaptor (BKM-250TG).
3D signal analyzing function
The monitor supports the following display modes of the
3D signal analyzing function if you install the optional
input adaptor (BKM-250TG). For this function, two-
dimensional (2D) view is used. The signals are not
displayed in stereoscopic view.
The available display modes differ depending on the serial
number of the BKM-250TG.
For the operation, see "Switching the Display of the 3D
Video Signal" on page 96.
Difference display (with serial number 7300001 or
higher):
The difference between the luminance signal of the left (L)
3D video signal and that of the right (R) signal is displayed.
This display is useful for checking parallax amount.
Checkerboard display (with serial number 7100001 or
higher):
The left (L) and right (R) 3D video signals are displayed in
a checkerboard pattern on the screen. This display is useful
for comparing the luminance or color settings of
neighboring L and R images.
L/R switching display (with serial number 7100001 or
higher):
The dual-stream left (L) and right (R) 3D video signals are
alternately displayed on the screen. This display is useful
for comparing the color or brightness of the L and R

Advertisement

Table of Contents

   Also See for Sony BVMF170A

   Related Manuals for Sony BVMF170A

Comments to this Manuals

Symbols: 0
Latest comments: