Korg MMT microKORG XL+ Owner's Manual page 75

FEEDBACK .......................................................................[000...127]
Sets the amount of feedback for the left and right channels.
PHASE ..........................................................................................[+, –]
This switches the phase of the output and feedback.
LFO SYNC (LFO Tempo Sync) .......................................................[OFF, ON]
Specifies whether the LFO cycle will be synchronized with the tempo speci-
fied by the [TEMPO] knob or MIDI clock.
 p. 66 "LFO SYNC (LFO Tempo Sync)"
LFO FREQ (LFO Frequency) ........................................ [0.01...100.0Hz]
Sets the LFO speed.
 p. 66 "LFO FREQ (LFO Frequency)"
SYNC.NOTE (LFO Sync Note) .............................................. [8/1...1/64]
Sets the LFO frequency as a proportion of the tempo set by the [TEMPO]
knob.  p. 66 "SYNC.NOTE (LFO Sync Note)"
This parameter will be displayed and can be set if "LFO SYNC" is ON.
NOTE
LFO WAVE (LFO Waveform) ............... [SAW, SQUARE, TRIANGLE, SINE, S&H]
Selects LFO Waveform.  p. 66 "LFO WAVE (LFO Waveform)"
LFO.SHAPE ..........................................................................[–63...+63]
 p. 66 "LFO.SHAPE"
KEY SYNC (LFO KeySync) ............................................................[OFF, ON]
Specifies whether the LFO will be reset by note-on.
 p. 67 "KEY SYNC (LFO KeySync)"
INI.PHASE (LFO Init Phase) ...................................................[000...180°]
Sets the starting location of the waveform.  p. 67 "INI.PHASE (LFO Init
Phase)"
This parameter will be displayed and can be set if "KEY SYNC" is ON.
NOTE
LFO SPRD (LFO Spread)....................................................[–180...+180°]
Sets the LFO phase difference between the left and right channels.
HI DAMP (High Damp)........................................................ [000...100%]
Sets the feedback damping amount in the high range.
13. VIBRATO (Stereo Vibrato)
This effect causes the pitch of the input signal to shimmer. Using the Auto-
Fade allows you to increase or decrease the shimmering speed.
Stereo In - Stereo Out
Left
Right
LFO LFO Shape
DRY/WET...................................................... ["DRY", 99:1...1:99, "WET"]
Sets the balance between the effect and dry sounds.
MOD.DEPTH (Modulation Depth)
Sets the depth of LFO modulation.
LFO SYNC (LFO Tempo Sync) .......................................................[OFF, ON]
Specifies whether the LFO cycle will be synchronized with the tempo speci-
fied by the [TEMPO] knob or MIDI clock.
 p. 66 "LFO SYNC (LFO Tempo Sync)"
LFO FREQ (LFO Frequency) ......................................... [0.01...100.0Hz]
Sets the LFO speed.
 p. 66 "LFO FREQ (LFO Frequency)"
SYNC.NOTE (LFO Sync Note) ..............................................[8/1...1/64]
Sets the LFO frequency as a proportion of the tempo set by the [TEMPO]
knob.
This parameter will be displayed and can be set if "LFO SYNC" is ON.
NOTE
 p. 66 "SYNC.NOTE (LFO Sync Note)"
LFO WAVE (LFO Waveform)................ [SAW, SQUARE, TRIANGLE, SINE, S&H]
Selects the LFO waveform.
 p. 66 "LFO WAVE (LFO Waveform)"
Effect guide
Dry / Wet
Vibrato
Vibrato
Dry / Wet
LFO Spread
...................................... [000...127]
75