Novell ZENWORKS 10 CONFIGURATION MANAGEMENT SP3 - SOFTWARE DISTRIBUTION REFERENCE 10.3 30-03-2010 Management Manual page 56

File Version: Determines the version of a file. The condition you use to set the requirement
includes the filename, an operator, and a version. The filename can be any file name supported by
the operating system. The possible operators are equals (=), does not equal (<>), is greater than (>),
is greater than or equal to (>=), is less than (<), and is less than or equal to (<=).
Be aware that file version numbers contain four components: Major, Minor, Revision, and Build.
For example, the file version for
independently. For this reason, the system requirements that you set might not provide your
expected results. If you do not specify all four components, wildcards are assumed.
For example, if you set the condition to
component of the version number (Major). As a result, versions 5.0.5, 5.1, and 5.1.1.1 also meet the
condition.
However, because each component is independent, if you set the condition to
the
calc.exe
IP Segment: Determines the device's IP address. After specifying the IP segment name using CIDR
(Classless Inter-Domain Routing) format, the two conditions you can use to set the requirement are
Yes and No. If you select Yes, the device's IP address must match the IP segment. If you select No,
the IP address must not match the IP segment.
You must specify the IP address using CIDR format. With CIDR, the dotted decimal portion of the
IP address is interpreted as a 32-bit binary number that has been broken into four 8-bit bytes. The
number following the slash (/n) is the prefix length, which is the number of shared initial bits,
counting from the left side of the address. The /n number can range from 0 to 32, with 8, 16, 24, and
32 being commonly used numbers. Examples:
123.45.67.12/16
123.45.67.12/24
Logged on to Primary Workstation: Determines whether the user is logged on to his or her
primary workstation. The two conditions you can use to set the requirement are Yes and No. If you
select Yes, the user must be logged on to his or her primary workstation to meet the requirement. If
you select No, if no user is logged on to the workstation, the requirement is not met. However, if a
user other than the primary user is logged on to the workstation, the requirement is met.
Memory: Determines the amount of memory on the device. The condition you use to set the
requirement includes an operator and a memory amount. The possible operators are equals (=), does
not equal (<>), is greater than (>), is greater than or equal to (>=), is less than (<), and is less than
or equal to (<=). The memory amounts are designated in megabytes (MB) and gigabytes (GB). For
example, if you set the condition to
meet the requirement.
Novell Client Installed: Determines if the device is using the Novell
connection. The two conditions you can use to set the requirement are Yes and No. If you select Yes,
the device must be using the Novell Client to meet the requirement. If you select No, it must not be
using the Novell Client.
Operating System - Windows: Determines the service pack level, server type, and version of
Windows* running on the device. The condition you use to set the requirement includes a property,
an operator, and a property value. The possible properties are service pack, server type, and version.
The possible operators are equals (=), does not equal (<>), is greater than (>), is greater than or
56 ZENworks 10 Configuration Management Software Distribution Reference
calc.exe
file must be less than or equal to version 5.1 to meet the requirement.
: Matches all IP addresses that start with 123.45.
: Matches all IP addresses that start with 123.45.67.
>= 2 GB
might be 5.1.2600.0. Each component is treated
, you are specifying only the first
calc.exe <= 5
, the device must have at least 2 gigabytes of memory to
calc.exe <= 5.1
®
Client for its network
TM
,