Universal Robots PolyScope X UR16e User Manual page 88

EU Declaration of Incorporation (DOI) (in accordance with 2006/42/EC Annex II B) original EN
I. Machinery Directive
2006/42/EC
II. Low-voltage Directive
2014/35/EU
III. EMC Directive 2014/30/EU
Reference to the harmonized standards used, as referred to in Article 7(2) of the MD & LV Directives and
Article 6 of the EMC Directive:
(I) EN ISO 10218-1:2011 TÜV Nord
Certificate # 44 708 14097607 (I) EN ISO
13732-1:2008 as applicable (I) EN ISO
13849-1:2015 TÜV Nord Certificate # 44 207
14097610 (I) EN ISO 13849-2:2012 (I) EN
ISO 13850:2015
Reference to other technical standards and technical specifications used:
(I) ISO 9409-1:2004 [Type 50-4-M6] (I)
ISO/TS 15066:2016 as applicable (III) EN
60068-2-1: 2007 (III) EN 60068-2-2:2007
The manufacturer, or his authorised representative, shall transmit relevant information about the partly
completed machinery in response to a reasoned request by the national authorities. Approval of full quality
assurance system (ISO 9001), by the notified body Bureau Veritas, certificate #DK015892.
1.11. Warranty Information
Content Universal Robots A/S continues to improve the reliability and performance of its
disclaimer products, and as such reserves the right to upgrade products, and product
documentation, without prior warning. Universal Robots A/S takes every care to ensure
the content of the User Manual/s is precise and correct, but takes no responsibility for
any errors or missing information.
This manual does not contain warranty information.
1.12. Certificates
UR16e PolyScope X
The following essential requirements have been fulfilled:
1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.4.3, 1.2.5, 1.2.6, 1.3.2, 1.3.4, 1.3.8.1, 1.3.9, 1.5.1, 1.5.2,
1.5.5, 1.5.6, 1.5.10, 1.6.3, 1.7.2, 1.7.4, 4.1.2.3, 4.1.3 Annex VI.
It is declared that the relevant technical documentation has been
compiled in accordance with Part B of Annex VII of the Machinery
Directive.
Reference the LVD and the harmonized standards used below.
Reference the EMC Directive and the harmonized standards used below.
(I) (II) EN 60204-1:2018 as
applicable (II) EN
60529:1991+A1:2000+A2:2013 (I)
EN 60947-5-5:1997+A1:2005
+A11:2013+A2:2017 (I) EN 60947-5-
8:2020 (III) EN 61000-3-2:2019
(II) EN 60320-1:2021 (III) EN 60068-
2-27:2008 (III) EN 60068-2-
64:2008+A1:2019
88
Part I Hardware Installation Manual
(II) EN 60664-1:2007 (III) EN 61000-3-3:
2013 (III) EN 61000-6-1:2019 UR3e &
UR5e ONLY (III) EN 61000-6-2:2019 (III)
EN 61000-6-3:2007+A1: 2011 UR3e &
UR5e ONLY (III) EN 61000-6-4:2019
(II) EN 61784-3:2010 [SIL2] (III) EN
61326-3-1: 2017 [Industrial locations SIL
2]
User Manual