Canon imagePROGRAF iPF8000S Service Manual page 294

Chapter 8
Code
(last 4 digits)
1400 No ink left.
to Press OK and
140C replace ink tank.
Ink tank is empty.
Replace the ink
tank.
1410 No ink tank
to loaded.
141C Check ink tank.
200A Paper size not
detected. Press Load/Eject
and reload the
paper.
Paper size not
detected. Reload paper.
Paper size not
detected. Press OK and
reload the paper.
200B Paper size not
detected. Reload paper.
200C Paper size not
detected.
Press Load/Eject
and reload the
paper.
Paper size not
detected.
Reload paper.
Paper size not
detected.
Lift the release
lever and reload
the paper.
200D Paper size not
detected.
Press Load/Eject
and reload the
paper.
Leading edge
detection error.
Lift the release
lever and align
leading edge
with orange line.
Paper size not
detected.
Lift the release
lever and reload
the paper.
Paper size not
detected.
Reload paper.
200E This paper
cannot be used.
Check supported
paper sizes.
This paper
cannot be used.
Check supported
paper sizes.
Load/Eject: Change Paper
8-6
Panel display Panel display
(Large LCD) (Small LCD)
Paper
Please Reload
Size Undetected
Paper
Please Reload
Size Undetected
Paper
Please Reload
Size Undetected
Papr Size
Undetected
Press Online Key
and Reload
Paper
Please Reload
Size Undetected
Paper Size
Please Check
Paper Too Small
Paper Size
Please Check
Paper Too Small
Press Online Key
Explanation/Detection sequence
Ink tank empty (continued use allowed)
The ink tank has run out of ink, but a
certain volume of ink is reserved in the
subtank. (The reserved volume of ink is put
to use after the remaining ink falls below
the pin check level.)
Displayed only on models having a
subtank.
(XX: Display applicable colors)
Last 2 digits: 00:Bk, 01:Y, 02:M, 03:C,
04:PM, 05:PC, 06:MBk1, 07:MBk2,
08:GY, 09:PGY, 0A:R, 0B:B, 0C:G
Ink tank not installed (continued use
allowed)
The ink tank is not installed but a sufficient
volume of ink is left in the subtank.
Displayed only on models having a
subtank.
This occurs in cases such as when the ink
tank cover is opened during printing, and
the ink tank is removed. (XX: Displays
applicable colors)
Last 2 digits: 10:Bk, 11:Y, 12:M, 13:C,
14:PM, 15:PC, 16:MBk1, 17:MBk2,
18:GY, 19:PGY, 1A:R, 1B:B, 1C:G
Paper size detection failure
Cannot detect the paper width (poorly
positioned paper).
Paper size detection failure
Paper is invalidly positioned on the platen.
Paper size detection failure
Cannot detect the leading edge of the
paper.
The leading edge of paper has been located
by coarse detection but not by a second
round of fine detection (up to 300 mm)
(semi-transparent paper).
(This is the message when the release lever
operation is not necessary.)
Paper size detection failure
Cannot detect the leading edge of the
paper.
The leading edge of paper has been located
by coarse detection but not by a second
round of fine detection (up to 300 mm)
(semi-transparent paper).
Paper size detection failure
Cannot detect the trailing edge of the paper.
-Cannot detect the trailing edge of the cut
sheet loaded after they have been fed 50
mm.
-Cannot locate the trailing edge of the
paper that has been found by coarse
detection.
Paper is too small
The width and length of paper detected are
shorter than the supported size (1.5%
margin).
Remedial Action
1. Replace the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
1. Mount the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
1. Check to see if roll paper are not
loaded in the cut sheet mode.
2. Load cut sheet.
1. Check paper conditions (soiling,
tear-offs, residual paper chips, residual
trimming cuts, folds)/size.
2. Has the paper been fed successfully
(without slippage under a load or any
influence)?
3. Has the LF adjustment value set
correctly?
4. Hasn't the loaded paper shrunk to
below its margin in the particular
environment?