Table of Contents
Advertisement
Section A
LED Flash Reject Code Conditions
Table A-5 lists the various LED Flash Reject Code causes and solutions for Banknotes.
Normal
Performance
Operation
Test
LED
LED
Sequence
Sequence
Yellow
Yellow
(3)
(2)
Yellow
Yellow
(3)
(3)
Yellow
Yellow
(3)
(4)
Yellow
Yellow
(3)
(5)
Yellow
Yellow
(3)
(6)
Yellow
Yellow
(3)
(7)
Yellow
Yellow
(3)
(8)
Yellow
Yellow
(3)
(9)
Green
Green
(3)
(1)
P/N 960-100933R_Rev. 2 {EDP #233449}
DBV™ Series DBV-500 Banknote Acceptor
Table A-5 LED Flash Reject Codes
Error
Sensors detected improper levels.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
Magnification Error
of this manual.
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensor detected and abnormal Banknote Type.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
Denomination
of this manual.
Error
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensor detected and abnormal Banknote Type.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
Pattern
for unacceptable Banknote.
Error
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
While transporting a Banknote, improper sensor levels were detected.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
for unacceptable Banknote.
Photo Level Error
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensors detected the Banknote length was longer or shorter than the
specified value.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
Banknote Length
for unacceptable Banknote.
Abnormal
[Relative Parts] Rollers, Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensors detected an improper Banknote pattern.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
for unacceptable Banknote.
Pattern Error 1
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensors detected the Banknote as invalid.
[Solution] Clean the Banknote Path.
Check that the Banknote is not damaged or exhibiting unfit conditions. Refer to
Invalid Banknote
"Banknote Fitness Requirements" on page 1-4 for unacceptable Banknote.
Error
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Sensors detected an improper Banknote pattern.
[Solution] Clean the Banknote Path. Check that the Banknote is not damaged or
exhibiting unfit conditions. Refer to "Banknote Fitness Requirements" on page 1-4
for unacceptable Banknote.
Pattern Error 2
[Relative Parts] Validation Sensor.
If the error is not resolved, change the above related part or parts and calibrate the
unit.
The Banknote has been inserted in an incorrect/crooked direction.
[Solution] Insert a Banknote in the proper alignment. Clean the Banknote Path and
Skewed Insertion
check the Centering Mechanism for proper operation.
Error
[Relative Parts] Centering Mechanism, Rollers.
If the error is not resolved, change the above related part or parts.
Causes and Solutions
© 2020 JAPAN CASH MACHINE CO., LTD.
A - 6
TroubleShooting
Advertisement
Table of Contents
