Lenovo ThinkEdge SE350 V2 Hardware Maintenance Manual page 128

Note: The imm.TpmTcmPolicyLock value must be 'Disabled', which means TPM_TCM_POLICY is
NOT locked and changes to the TPM_TCM_POLICY are permitted. If the return code is 'Enabled'
then no changes to the policy are permitted. The planar may still be used if the desired setting is
correct for the system being replaced.
2. Configure the TPM_TCM_POLICY into XCC:
– For customers in Chinese Mainland with no TPM, or customers that require to disable TPM:
OneCli.exe config set imm.TpmTcmPolicy "NeitherTpmNorTcm" --override --imm <userid>:<password>@<ip_
address>
– For customers in Chinese Mainland that require to enable TPM:
OneCli.exe config set imm.TpmTcmPolicy "NationZTPM20Only" --override --imm <userid>:<password>@<ip_
address>
– For customers outside Chinese Mainland that require to enable TPM:
OneCli.exe config set imm.TpmTcmPolicy "TpmOnly" b --imm <userid>:<password>@<ip_address>
3. Issue reset command to reset system:
OneCli.exe misc ospower reboot --imm <userid>:<password>@<ip_address>
4. Read back the value to check whether the change has been accepted:
OneCli.exe config show imm.TpmTcmPolicy --override --imm <userid>:<password>@<ip_address>
Notes:
– If the read back value is matched it means the TPM_TCM_POLICY has been set correctly.
imm.TpmTcmPolicy is defined as below:
– Value 0 use string "Undefined" , which means UNDEFINED policy.
– Value 1 use string "NeitherTpmNorTcm", which means TPM_PERM_DISABLED.
– Value 2 use string "TpmOnly", which means TPM_ALLOWED.
– Value 4 use string "NationZTPM20Only", which means NationZ_TPM20_ALLOWED.
– Below 4 steps must also be used to 'lock' the TPM_TCM_POLICY when using OneCli/ASU
commands:
5. Read TpmTcmPolicyLock to check whether the TPM_TCM_POLICY has been locked , command as
below:
OneCli.exe config show imm.TpmTcmPolicyLock --override --imm <userid>:<password>@<ip_address>
The value must be 'Disabled', it means TPM_TCM_POLICY is NOT locked and must be set.
6. Lock the TPM_TCM_POLICY:
OneCli.exe config set imm.TpmTcmPolicyLock "Enabled"--override --imm <userid>:<password>@<ip_address>
7. Issue reset command to reset system, command as below:
OneCli.exe misc ospower reboot --imm <userid>:<password>@<ip_address>
During the reset, UEFI will read the value from imm.TpmTcmPolicyLock, if the value is 'Enabled' and
the imm.TpmTcmPolicy value is valid, UEFI will lock the TPM_TCM_POLICY setting.
Note: The valid values for imm.TpmTcmPolicy include 'NeitherTpmNorTcm', 'TpmOnly', and
'NationZTPM20Only'.
If the imm.TpmTcmPolicyLock is set as 'Enabled' but imm.TpmTcmPolicy value is invalid, UEFI will
reject the 'lock' request and change imm.TpmTcmPolicyLock back to 'Disabled'.
8. Read back the value to check whether the 'Lock' is accepted or rejected. Command as below:
OneCli.exe config show imm.TpmTcmPolicy --override --imm <userid>:<password>@<ip_address>
Note: If the read back value is changed from 'Disabled' to 'Enabled' that means the TPM_TCM_
POLICY has been locked successfully. There is no method to unlock a policy once it has been set
other than replacing system board.
ThinkEdge SE350 V2 Hardware Maintenance Guide
120