Table of Contents
Advertisement
SwitchBlade x8112 Chassis Switch and AT-SBx81CFC960 Card Installation Guide
Figure 109: Positioning the Handle on the Transceiver..................................................................................................... 179
Figure 111: Installing an AT-SP10TW Cable in the AT-SBx81CFC960 Controller Fabric Card........................................ 182
Figure 112: AC Sockets on the Rear Panel of the AT-SBx8112 Chassis.......................................................................... 186
Supply................................................................................................................................................................................ 187
Anchor ............................................................................................................................................................................... 188
Figure 115: Connecting the AC Power Cord for the AT-SBxPWRPOE1 Power Supply.................................................... 189
Figure 116: Securing the Power Cord for the AT-SBxPWRPOE1 Power Supply to an Anchor ........................................ 190
Figure 117: Dress and Secure AC Power Cords ............................................................................................................... 191
Figure 118: Components of the AT-SBxPWRSYS1 DC Power Supply............................................................................. 193
Figure 119: Grounding Wire Terminal ............................................................................................................................... 194
Figure 120: Stripping the Stranded Grounding Wire.......................................................................................................... 194
Figure 121: Attaching the Stranded Grounding Wire to the Grounding Terminal .............................................................. 194
Figure 122: Removing the Nut and Washer from the Grounding Post .............................................................................. 195
Figure 123: Installing the Grounding Wire ......................................................................................................................... 196
Figure 124: Stripping the solid or Stranded Grounding Wire ............................................................................................. 197
Figure 125: Attaching the Bare Grounding Wire to the Grounding Post............................................................................ 197
Figure 126: Securing the Bare Grounding Wire to the Grounding Post............................................................................. 198
Figure 127: Power Wire Terminals .................................................................................................................................... 199
Figure 128: Stripping the Power Wires .............................................................................................................................. 200
Figure 129: Attaching the Power Wires to the Straight Terminal Lugs .............................................................................. 200
Figure 130: On/Off Switch on the AT-SBxPWRSYS1 DC Power Supply .......................................................................... 201
Figure 131: Opening the Plastic Cover.............................................................................................................................. 202
Figure 132: Removing the Terminal Screws...................................................................................................................... 203
Figure 133: Connecting the Positive (+) Power Wire with a Straight Terminal.................................................................. 204
Figure 134: Connecting the Negative (-) Power Wire with a Straight Terminal ................................................................. 205
Figure 135: Closing the Plastic Cover over the Terminal Connectors ............................................................................... 206
Figure 136: Tightening the Handle Locking Screw ............................................................................................................ 207
Figure 137: Stripping the Power Wires .............................................................................................................................. 208
Figure 138: Attaching the Power Wires to the Right Angle Terminals............................................................................... 208
Figure 139: Removing the Plastic Cover ........................................................................................................................... 209
Figure 140: Removing the Terminal Screws...................................................................................................................... 210
Figure 141: Connecting the Positive (+) Power Wire with a Right Angle Terminal............................................................ 211
Figure 142: Connecting the Negative (-) Power Wire with a Right Angle Terminal ........................................................... 212
Figure 143: Tightening the Handle Locking Screw ............................................................................................................ 213
Figure 144: Stripping Solid or Stranded DC Power Wires ................................................................................................. 214
Figure 145: Connecting the Positive Wire With Bare Wire ................................................................................................ 215
Figure 146: Connecting the Negative Lead Wire with Bare Wire ...................................................................................... 216
Figure 147: Initialization Messages for a Stand-alone Switch ........................................................................................... 219
Figure 148: Initialization Messages for a Stand-alone Switch (Continued) ....................................................................... 220
Figure 149: Connecting the Management Cable to the Console RS-232 Port .................................................................. 224
Figure 150: SHOW VERSION Command.......................................................................................................................... 225
Figure 151: SHOW CARD Command................................................................................................................................ 226
Figure 152: Disconnecting the AC Power Cord from the AC Socket on the Back Panel................................................... 245
Figure 153: Lifting the Locking Handle on the Power Supply ............................................................................................ 246
Figure 154: Removing the Power Supply from the Chassis .............................................................................................. 247
Figure 155: Installing a Blank Power Supply Slot Cover ................................................................................................... 248
Figure 156: Lowering the Locking Handle on the Power Supply Slot Cover ..................................................................... 249
Figure 157: Loosening the Screw on the Locking Handle ................................................................................................. 250
Figure 158: Opening the Plastic Window over the Terminal Block.................................................................................... 251
Figure 159: Removing the Negative Lead Wire................................................................................................................. 252
Figure 160: Removing the Positive Lead Wire from the Terminal Block ........................................................................... 253
Figure 161: Reinstalling the Screws on the Positive and Negative Terminals................................................................... 254
Figure 162: Closing the Plastic Cover ............................................................................................................................... 255
Figure 163: Removing the Grounding Wire ....................................................................................................................... 256
Figure 164: Reinstalling the Nut and Washer on the Grounding Post ............................................................................... 257
Figure 165: Lifting the Locking Handle and Removing the Power Supply......................................................................... 258
Figure 166: Installing a Blank Power Supply Slot Cover ................................................................................................... 259
11
Advertisement
Table of Contents
Troubleshooting
