Quantum SNC 4000 User Manual page 136

State = 0, Type = 1, Flags = 0x00000000, Online
WWN: 200000e0:8b0057d8
Name: 'LABATTS'
Host Type: 'NT 4.0 SP5'
Device Id: 'ScsiPort6 [0:0:0] (QLA2100)
LUN Access:
0: 01 01 01 00 00 00 00 00 00 00 00 00 00 01 01 00
16: 00 00 00 00 00 00 00 00 00 01 01 00 00 00 00 00
32: 00 00 00 00 00 01 01 00 00 00 00 00 00 00 00 00
48: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
64: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
96: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
112: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
128: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
144: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
160: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
176: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
192: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
208: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
224: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
240: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
value = 0 = 0x0
SNC >
vpsInactiveSet
The vpsInactiveSet command de-activates VPS or eVPS making all LUNs available to all host
connections. This command typically would be used when troubleshooting a SAN configuration. It removes
eVPS access control without deleting VPS or eVPS access settings. Use the sfmActiveSet command to
re-activate VPS or eVPS.
SNC > vpsInactiveSet
value = 0 = 0x0
SNC >
If VPS or eVPS is already inactive, the following is displayed.
SNC > vpsInactiveSet
VPS: Already Inactive
value = 23 = 0x17
SNC >
vpsMapAdd [devID] [hostIndex] [lun]
The vpsMapAdd command assigns a target device (devId) to a host (hostIndex) with the specified
Logical Unit Number of (lun). If the assignment is successful, the value 0 is output. If the assignment fails,
the value -1 is output. In the example below, the assignment was successful.
Device ID can be determined by finding the device in the list generated by mapShowDevs.
Existing hostIndex values can be determined by looking at the "ID" column in the output of the
[hostIndex]command.
To verify the effects of the vpsMapAdd command, issue the
SNC > vpsMapAdd 1,6,3
value = 0 = 0x0
SNC > vpsMapShow
Host Lun Internal Chan Id Lun Vendor Product Rev SN
130
vpsMapShow [hostIndex]
Service Port Command Reference
sfmShow
command.