Table of Contents
Advertisement
ORTHORALIX 9200
Service Manual
4.3.6. Subnet mask
This service program is applicable only for the Orthoralix 9200 DDE
versions.
By selecting this service program it is possible to check and to
change the Subnet Mask address of the Orthoralix 9200 DDE when
it is connected to the LAN network. The Subnet Mask address is
made of four numbers, having a range from 0 to 255. A default
address is stored: it is possible to modify it by:
1)
pressing keys kV + and kV - for the first number on the left
2)
pressing keys mA + and mA - for the second number on the
left
3)
pressing keys s + and s - for the third number on the left
4)
pressing keys progam + and program - for the last number
The following message will appear on the display:
SUBNET MASK:
Please take note that the address appears on the display only
when the connection to the LAN network is done properly: it takes
approximately 30 s from the system switching on. So, if this service
program is selected during this time, the address displayed is: 0,0,0,0.
After the modification of the Subnet Mask address, to store it in the
system, press Dummy Run: for a while on the display will appear
0,0,0,0 and then the new Subnet Mask address.
W
n I
a c
e s
o
P f
7 A
o b
r a
r d
p e
a l
e c
e b
s
o t
e r
i d
t n
e h
e n
w
P
7 A
b
a o
4.3.7. Host input read
With this service program you can visualize the status of the
hardware inputs of the host computer board PC1, with four
hexadecimal numbers.
In this way you can check whether the host computer board
recognizes the right inputs signals.
The correspondence between the hexadecimal numbers and the
status of the hardware inputs is shown in pag FZ-1.
DENTSPLY Gendex
0 0 0 0
A
R
N
N I
G
m
n e
t , t
e h
u S
n b
t e
M
a
k s
a
d d
e r
s s
d r
y b
s u
n i
t g
s i h
e S
i v r
e c
r P
g o
4.3.8. Pan PA5 menu
With this service program is possible to enable/disable the detection
of the Pan PA5 board by the host computer board PC1 at the system
start up.
It is also possible to check the status of the optoswitches mounted
on the secondary slit.
The following message will appear on the display:
where:
XX = if the AEC sensor is present on the PA5 board, this
value should be from 0 to 10; if the AEC sensor is not
present on the PA5 board, this value is FF
SLD = nW = status of the secondary slit optoswitches
N = narrow collimator (panoramic projections)
W= wide collimator (transcan)
When the optoswitches are activated, the letters are in capital;
when they are not activated the letters are smaller.
ENA<Y> = by pressing the Program + or Program - keys on
the keyboard, it is possible to enable (Y) or disable (N) the
PA5 board detection at the start up. The board should be
always enabled (Y). In case of activation of the service
program Default EEPROM, the PA5 board is disabled and
should be enabled again.
Suggestions:
(1)
The status of the optoswitches can be:
nW= wide collimator selected
m
u
t s
Nw= narrow collimator selected
a r
. m
nw= transition from narrow to wide collimator or vice versa
NW= error condition: in this case the alarm Secondary slider
is generated (see the alarm explanation for more details).
(2)
If one or both optoswitches are damaged, it is possible to
disable the PA5 board, so that the alarm disappears, the
AEC function is disabled, but the system can be used
selecting manually the exposure parameters.
4.3.9. Ceph PA5 menu
With this service program is possible to enable/disable the detection
of the Ceph PA5 board by the host computer board PC1 at the
system start up.
The following message will appear on the display:
where:
XX= if the AEC sensor is present on the PA5 board, this
value
should be from 0 to 10;
if the AEC sensor is not present on the PA5 board, this
value is FF
ENA<Y>= by pressing the Program + or Program - keys on
the keyboard, it is possible to enable (Y) or disable (N) the
PA5 board detection at the start up. The board should be
always enabled (Y).
In case of activation of the service program Default EEPROM,
the PA5 board is disabled and should be enabled again. If the
Orthoralix system is without the ceph arm, the Ceph PA5 board
must be disabled.
(03.0)E
PAN PA5 MENU
XX SLD=nW ENA<Y>
CEPH PA5 MENU
XX ENA<Y>
Section F
F-21
Advertisement
Chapters
Table of Contents
