Table of Contents
Advertisement
ORTHORALIX 9200
Service Manual
1.6.
MOTORISED COLUMN
Instead of the manual vertical movement of the Z-carriage onto
the column, is available a motorised column which allows
automatic vertical movement of the Z-carriage. A motor is mounted
in the top part of the column.
The operator will be able to move vertically the Z-carriage
controlling this motor by:
•
two up/down push buttons located on the operator panel
•
one push button on the Ceph arm.
The operator must continue to push the buttons to maintain in
movement the Z-carriage.
The buttons control the motor in the following way:
•
one-shot short pressure (<500 msec) of the buttons will cau-
se 1 mm movement
•
prolonged pressure of the buttons will cause:
- slow movement (3 mm/s), during the first 2 s; on release, a
decelerating ramp is activated (time from Vmax to 0 is
300mS)
- fast movement (20 mm/s), after 2 s.
The vertical movement is stopped by two end run optoswitches
(upper and lower), placed on the front part of the column.
W
D
o
n
t o
m
o
v
e
h t
e
Z
c -
a
r r
a i
s
s y
e t
m
s i
o
f f
d :
o
n i
g
s
o
t i
c
o
1.7.
REAL TIME DIGITAL PANORAMIC
A)
ORTHORALIX 9200 DPI
The Orthoralix 9200 DPI is a version of the Orthoralix 9200 family
providing real time digital image acquisition, by using a digital CCD
cassette sensor interconnected with a Personal Computer.
The X-ray Image sensor and the Processing Unit (IPU) is storing the
data (i.e. the digital image) in a memory and then is transferring the
data to a Personal Computer by using an wired connection.
The IPU acquires the image by an autotrigger, as soon the X-rays
are arriving on the digital CCD cassette sensor.
The Orthoralix 9200 DPI operates only in panoramic mode (the
Transcan projections are disabled) so, it can perform the following
projections :
P
R
O
. 1
S
T
A
N
D
A
R
D
P
A
N
O
R
A
M
. 2
C
H
L I
D
. 3
O
R
T
. H
D
E
N
T
T I
O I
N
. 4
F
R
O
N
T
A
L
D
E
N
T
T I
O I
N
. 5
R
G I
H
T
J
A
W
. 6
L
E
F
T
J
A
W
. 7
E
M
O I
R
T
H
O
G
O
N
A
L
R
. 8
E
M
O I
R
T
H
O
G
O
N
A
L
L
E
. 9
F
R
O
N
T
A
L
S
N I
U
S
1
. 0
R
G I
H
T
L
A
T
E
R
A
L
S
N I
1
. 1
L
E
F
T
L
A
T
E
R
A
L
S
N I
U
1
. 2
F
R
O
N
T
A
L
T
M
J
1
. 3
L
A
T
E
R
A
L
T
M
J
DENTSPLY Gendex
A
R
N
N I
G
g
e
a
o l
n
g
h t
e
c
o
u l
m
n
w
h
u
d l
d
a
m
a
g
e
h t
e
P
C
6
b
o
r a
J
E
C
T
O I
N
C I
G I
H
T
F
T
U
S
S
Also the AEC functionality is disabled in the panoramic mode.
Two field upgrading kits to upgrade any Orthoralix 9200\Plus to the
digital panoramic are available (for more information refer to the
relevant Service Manual):
1)
9869 104 01901
2)
9869 104 01911 for systems till s/n 870105
The acquired image will be handled by the Dentsply Gendex VixWin
software supplied with the 9200 DPI.
B)
ORTHORALIX 9200 DDE
The Orthoralix 9200 DDE is a version of the Orthoralix 9200 family
providing real time digital image acquisition, by using a digital CCD
sensor interconnected with a Personal Computer, by using an
Ethernet connection.
The Orthoralix 9200 DDE operates in all the enabled projections,
including the cephalometric projections in the versions with the
ceph arm.
e
n
h t
e
. d
(03.0)E
Section A
A-3
Advertisement
Chapters
Table of Contents
