ZyXEL Communications XMG1930 Series User Manual page 208

Table 96 Advanced Application > Multicast > IPv4 Multicast > IGMP Snooping (continued)
LABEL DESCRIPTION
Querier Select this option to allow the Switch to send IGMP General Query messages to the VLANs with
the multicast hosts attached.
Querier Version IGMP snooping query works only when both host and Switch support the same IGMP version.
Select v2 to allow the Switch to send IGMPv2 queries only.
Select v3 to allow the Switch to send IGMPv3 queries only.
Report Proxy Select this option to allow the Switch to act as the IGMP report proxy and leave proxy. It will
report group changes to a connected multicast router.
The Switch not only checks IGMP packets between multicast routers or switches and multicast
hosts to learn the multicast group membership, but also replaces the source MAC address in
an IGMP v1/v2 report with its own MAC address before forwarding to the multicast router or
switch. When the Switch receives more than one IGMP v1/v2 join report that requests to join
the same multicast group, it only sends a new join report with its MAC address. This helps
reduce the number of multicast join reports passed to the multicast router or switch.
The Switch sends a leave message with its MAC address to the multicast router or switch only
when it receives the leave message from the last host in a multicast group.
Host Timeout Specify the time (from 1 to 16711450) in seconds that elapses before the Switch removes an
IGMP group membership entry if it does not receive report messages from the port.
802.1p Priority Select a priority level (0 – 7) to which the Switch changes the priority in outgoing IGMP control
packets. Otherwise, select No-Change to not replace the priority.
IGMP Filtering Select Active to enable IGMP filtering to control which IGMP groups a subscriber on a port
can join.
If you enable IGMP filtering, you must create and assign IGMP filtering profiles for the ports that
you want to allow to join multicast groups.
Unknown Multicast Specify the action to perform when the Switch receives an unknown multicast frame.
Frame
• Select Drop to discard the frames.
• Select Flooding to send the frames to all ports.
• Select Drop on VLAN and enter the VLAN ID numbers to discard the frames on the
specified VLANs. Use a dash to specify consecutive VLANs and a comma (no spaces) to
specify non-consecutive VLANs. For example, 51–53 includes 51, 52 and 53, but 51,53 does
not include 52.
Unknown Multicast Specify the action to perform when Unknown Multicast Frame is set to Drop.
Frame to Querier
• Select Drop to discard the frames.
Port
• Select Forwarding to send the frames to all querier ports.
• Select Forwarding on VLAN and enter the VLAN ID numbers to send the frames to the ports
which are used as an IGMP query port on the specified VLANs. Use a dash to specify
consecutive VLANs and a comma (no spaces) to specify non-consecutive VLANs. For
example, 51–53 includes 51, 52 and 53, but 51,53 does not include 52.
Reserved Multicast The IP address range of 224.0.0.0 to 224.0.0.255 are reserved for multicasting on the local
Group network only. For example, 224.0.0.1 is for all hosts on a local network segment and 224.0.0.9 is
used to send RIP routing information to all RIP v2 routers on the same network segment. A
multicast router will not forward a packet with the destination IP address within this range to
other networks. See the IANA web site for more information.
The layer-2 multicast MAC addresses used by Cisco layer-2 protocols, 01:00:0C:CC:CC:CC
and 01:00:0C:CC:CC:CD, are also included in this group.
Specify the action to perform when the Switch receives a frame with a reserved multicast
address.
• Select Drop to discard the frames.
• Select Flooding to send the frames to all ports.
Port This field displays the port number.
Chapter 24 Multicast
XMG1930 Series User's Guide
208