Specification - AMF S-100 Parts And Service Manual

S-311
4. S P E C I F I C AT I O N
S-311 Elektronic buttonhole machine with chain stitch is possible to use for men`s and women`s wear.
Possible to use gimp thread, not in round eye.
Machine type/model
Sewing speed
The length
of hole
Stitch Density
Number of stitches in the eye
Bite Range Elecctronic
Bite Range Elecctronic (???)
Buttonhole style
Eye type
Flybar length
Length of the cross bar
Cross bar density
Number of stitches in the round end
Clamp foot height (max)
Maximum work thickness
Buttonhole Cutting Mode
Cutting Space
Cut position (Y axis)
Bedplate movement
Needle system
Recommended threads*
Upper thread trimming
Lower thread and gimp trimming
L = 3 to 7 mm
Cutting space
Operating Condition
Air pressure
Machine db Level
Machine Head Dimension
Machine Head Weight
Table Dimensions
Machine Weight
Electrical requirements
Line Circuit Breaker
* N o t e : If a customer uses thread size 100 and less, the manufacturer recommends to use the left looper 17.0069.4.019
If you use poor quality threads on the machine, the thread can burn at the needle (producer recommend
decrease machine´s speed).
→
** Gimp 10 - 30
30 - 100 →
1-4
A
INTRODUCTION
-
AF
1000 to 2000 stitches/min (500 to 1000 rev/min of the drive shaft)
10 to 50 mm
2,1 mm (AF, LTT); 2,3 mm (CT) (± 0,3 mm electronic); 2,7 mm (± 0,3 mm electronic)
2,1 mm (AF, LTT); 2,3 mm (CT) (± 0,5 mm electronic); 2,7 mm (± 0,5 mm electronic)
max 3,5 mm
No eye; 2,2 x 3,0 mm; 2,8 x 4,2 mm; 3,0 x 4,6 mm; 3,2 x 5,0 mm; 3,4 x 4,2 mm
3,0 - 20,0 mm
4 to 8 mm
0,5 to 1,5 mm
4 to 20
02.0558.0.111 (Nm 100)
80, 100, 120, gimp size 30-100
according to IEC 364-3, IEC 364-5-51 temperature from +5° C to 40° C, relative air humidity from 30 to 8 0%
L =86,9db; L =74,8 db; Noise measurement according to EN ISO 3746:1995
wA pfA
530 mm (height) x 370 mm (width) x 560 mm (depth)
730 mm (height) x 1100 mm (width) x 700 mm depth)
1NPE~60Hz 230 V/TN/S; 1NPE~50Hz 230 V/TN/S
CT Throat Plate
CT Throat Plate
e-mail: service@amfreece.cz; parts@amfreece.cz; website: www.amfreece.com
Phones: +420 582 309 146 (Service); +420 582 309 286 (Spare Parts); Fax: +420 582 360 606
CT 14 - 24 mm
14 to 24mm
0,5 to 2,0 mm (increments of 0,1 mm)
4 to 20
See section D 3.3
4 to 6 mm
0,5 to 1,5 mm
12 mm
in 8,0 mm
Cut before (CB), cut after (CA), no cut (OFF)
- 0,50 to + 1,2 mm
± 1,5 mm
64 mm
02.0558.1.112 (Nm 110)
80, 100, 120, gimp size 10-30 standard **
(Short ends)
L = 14 to 24mm
L+L = 21 to 31mm
1
0,55 MPa = 80 PSI
64 kg
175 kg
Min. 10A Characteristic C (EN60947-2)
10.4012.5.016
10.4012.1.016
10.4012.2.014
CT 22 - 32mm
22 to 32mm
L = 22 to 32mm
L+L = 29 to 39mm
1
+ 150 mm distance
Revised 02/2009