ELECTRO FREEZE FREEDOM 360 Series Operator's Manual page 82

30T 30T -RMT -RMT
30T 30T-RMT 30T -RMT -RMT, 88T
This instruction sheet is not intended to be used in place of the Operator's Manual. Use the following information
to assist you only after you have read, understood, and are accomplished in the procedures for cleaning and
sanitizing detailed in the Electro Freeze freezer Operator's Manual.
DRAINING PRODUCT
Follow Closing Procedures in Operator's Manual to remove frozen
product from the freezer.
1. Turn selector switches to "CLEAN", MTS (MIX) switches to
"ON", CAB switch to "OFF".
2. Empty the remaining mix out of mix containers.
3. Run beaters 5 minutes to soften product. Dispense as much
frozen product as possible.
4. Pour 2 gallons of cool water into each mix cont ainer, allowing
the cylinders to fill with water .
5. Open plungers to drain mix and water . Repeat step 4 until
water is clear.
6. Prepare and pour 2 gallons of warm sanitizing solution of
100ppm available chlorine in cont ainer.
7. Open air bleed and fill each cylinder with sanitizer . Close air
bleed. Place selector switch to clean for 5 minutes.
8. Put all switches in the "OFF" position. Drain completely.
DISASSEMBLY
CAUTION: To avoid electrical shock or cont act with
moving parts, make sure all switches are in the
"OFF" position and that the main power supply is
disconnected. Some freezers have more than one
disconnect switch.
CAUTION: PRESSURIZED SYSTEM.
Plungers must be open before disassembly .
Disassemble the freezer components in accordance with the
Operator's Manual instructions.
1. Remove dispensing head and beater shaf ts from freezer .
Disassemble MTS and move to cleaning area.
1. Prepare a three-compartment sink for cleaning, rinsing, and
sanitizing parts removed from the freezer per applicable health
codes. The sanitizer should be mixed according to the
manufacturer's instructions to yield 100 parts per million (PPM)
available chlorine solution. (example: S tera-Sheen Green
Label).
2. Disassemble all parts and remove o-rings. Clean each part
with the appropriate brush supplied with freezer .
3. Wash with a warm dish detergent solution, rinse, sanitize, and
air dry all parts removed from the freezer . For proper sanitizing,
the parts must remain in the sanitizer for 5 minutes.
4. Go to freezer and use warm dish detergent solution thoroughly
brush the mix feed tubes from the refrigerated cabinet to the
cylinders, the inside of the cylinder making certain to clean the
back walls and the inside of the drain tube.
5. Repeat Step 4 with sanitizing solution.
Cleaning & Sanitizing Electr Cleaning & Sanitizing Electr
Cleaning & Sanitizing Electro F Cleaning & Sanitizing Electr Cleaning & Sanitizing Electr
, 88T , 88T -RMT -RMT , 99T , 99T
, 88T , 88T-RMT -RMT, 99T -RMT , 99T , 99T-RMT and 180T
CLEANING
o Fr r r r r ee o F o F
o F
-RMT and 180T -RMT and 180T
-RMT and 180T -RMT and 180T-RMT F
Assemble and
lubricate freezer
components in
accordance with
the Operator's
Manual instruc-
tions.
0-RING-PLUNGER
PIN-HANDLE
KNOB-HAND
HANDLE
1. Wash and sanitize your hands and forearms.
2. Prepare 2 gallons (7.5 liters) of sanitizing solution in each
mix container. Sanitizing solution must be mixed according
to manufacturer's instructions to yield 100 PPM (parts per
million) available chlorine solution.
3. Brush the interior mix container walls, the underside of the
container covers, and low mix probes with sanitizer solution.
4. Place the mix containers with sanitizer in the refrigerated
cabinet, insert pickup tube and sanitize exterior of the tubes.
5. Place an empty container under the dispensing head.
6. Open the air bleed plugs by pulling up until the plugs touch
the bottom of the switch box.
7. Reconnect the main power supply to the freezer . Turn the
MTS (MIX) switches to "ON". This will pump the sanitizer into
the cylinders.
8. When sanitizer flows out the bottom of the dispense
close the air bleed plugs.
ee ee eez z z z z e e e e e
ee
® ® ® ® ®
-RMT Fr r r r r ee -RMT F -RMT F ee ee eez z z z z er er er er ers s s s s
-RMT F ee
ASSEMBLY
AIR METER
TUBE-ASSY MIX INLET
TUBE-AIR
CLIP-TUBE
HOSE CLAMP
R ETAINER
O-RING
PORT-ASSY
INLET MIX/AIR
BOOT-MIX TUBE
DUCKBILL V ALVE
NOZZLE
SANITIZING
BRAIDED HOSE ASSY
AIR INLET PORT
HOSE CLAMP
MIX TRANSFER HOSE
(DO NOT TWIST)
HOSE LOCATING
LINE
PLUNGER
PLUG-AIR BLEED
O-RING-PLUG
ROD-PLUNGER
O-RING-HEAD
HEAD
HEAD
head,
(over)