Page 1
OPERATOR’S MANUAL with Illustrated Parts List COMPACT SERIES SHAKE FREEZER Model CS700-FG 185231 - 2/14 H. C. Duke & Son, LLC P/N 185231 - November 2015 Printed in U.S.A.
ELECTRO FREEZE Shake Model CS700-FG SAFETY FIRST! Follow these four steps to safety ..1. Recognize Safety Information ..Look for this safety alert symbol throughout this manual. When you see this symbol on your freezer or in this manual, be alert to the potential for personal injury.
Page 5
NOT operate the freezer unless all service panels and access doors are secured with screws. DO NOT attempt to maintain or repair the freezer until the main power supply has been disconnected. Contact your local Electro Freeze Distributor for authorized service.
Page 6
If it is necessary to replace any label, E-mail: service@electrofreeze.com please contact your local authorized Electro Freeze Distributor or H. C. Duke & Son. When ready to order you will need to (The decals on the next page are determine the (1) part number, (2) type of numbered 1 and 2.
ELECTRO FREEZE Shake Model CS700-FG Introduction This freezer is designed to produce If you require technical assistance, please milkshakes with a temperature range of contact the factory service department at 24° to 30°F (-4° to -1°C). If such products H.C. Duke & Son, LLC. as follows:...
ELECTRO FREEZE Shake Model CS700-FG Electrical Requirements 3. Supply voltage must be within CAUTION ±10% of voltage indicated on the All materials and nameplate. Request your local power connections must conform company to correct any voltage problem. to local requirements and be in compliance with the 4.
Figure 3-1 Reference Information Fill in the following information as soon as you receive the Electro Freeze CS700-FG. (The item numbers — encircled, below — correspond with the callout numbers in figure 4-1.) 1.) Model Number: _________________ 2.) Serial Number:__________________...
Installation Date Fill in the date of installation, and the name, address, and phone number of the installer in the space provided below. This information will be needed when ordering parts or service for the CS700-FG Freezer. Date of installation: _____________________________________...
ELECTRO FREEZE Shake Model CS700-FG Part Names and Functions Figure 4-1 Head Assembly 185231-17...
Page 17
ELECTRO FREEZE Shake Model CS700-FG Part Names and Functions — continued The following part names and descriptions refer to figure 4-1. 1.) HEAD - ASSY. DISPENSE: Encloses the freezing cylinder and provides an opening for product to be dispensed. 2.) BUSHING - BEATER BEARING: Holds the beater in place at the front of the cylinder.
Page 18
ELECTRO FREEZE Shake Model CS700-FG Part Names and Functions — continued SEAL CUP- BEATER SHAFT WASHER - BEATER SHAFT SEAL CUP- BEATER SHAFT BEATER - ASSY. SHAKE SHORT BLADE - SHAKE SCRAPER Figure 4-2 Beater Shaft The following part names and descriptions refer to figure 4-2.
Page 19
ELECTRO FREEZE Shake Model CS700-FG Part Names and Functions — continued O-Ring Tube-Mix Feed Insert-Assy. Mix Feed O-Ring Figure 4-3 Mix Feed Tube The following part names and descriptions refer to figure 4-3. 1.) TUBE-MIX FEED: Meters the correct amount of mix and air into the freezing cylinder from the hopper.
ELECTRO FREEZE Shake Model CS700-FG Operator Controls Figure 5-1 The following paragraphs describe the CAUTION operator controls and indicators. Refer to Test operation of the head figure 5-1 for location of these controls switch prior to placing and indicators on the freezer.
ELECTRO FREEZE Shake Model CS700-FG Operator Controls — continued Reset — Circuit Breaker (2) This control protects the beater motor Important: against failure from an overload condition If the circuit breaker trips frequently, your freezer should be checked for by automatically shutting down the freezer.
ELECTRO FREEZE Shake Model CS700-FG Disassembly and Cleaning 6.1 Cleaning Accessories The following accessories shipped with the freezer are necessary for cleaning, sanitizing, and disassembly/assembly: 1. BRUSH - HC158010. 6-inch 6. LUBRICANT - PETROL GEL diameter used to clean the cylinder.
ELECTRO FREEZE Shake Model CS700-FG 6.2 Disassembly Instructions Figure 6-2 Dispense Head Assembly CAUTION CAUTION To avoid electrical shock To prevent bacteria growth, or contact with moving remove ALL O-rings when parts, make sure all disassembling for cleaning. switches are in the “OFF”...
Page 24
ELECTRO FREEZE Shake Model CS700-FG 6.2 Disassembly Instructions — continued SEAL CUP- BEATER SHAFT WASHER - BEATER SHAFT SEAL CUP- BEATER SHAFT BEATER - ASSY. SHAKE SHORT BLADE - SHAKE SCRAPER Figure 6-3 Beater Shaft Assembly O-Ring 6. Remove the plunger (6, figure...
ELECTRO FREEZE Shake Model CS700-FG 6.3 Cleaning Instructions CAUTION 2. Wash all parts removed from the To prevent bacteria growth, freezer thoroughly with a dish detergent remove all O-rings when solution. Clean the following parts with the cleaning. Failure to do...
Page 26
ELECTRO FREEZE Shake Model CS700-FG Cleaning Instructions — continued c. The shaft seal and plunger O-ring grooves (figure 6-6). d. The beater shaft and the scraper blade pin holes, shown in figure 6-7. 3. After all parts are washed and rinsed place them in the sanitizing solution.
ELECTRO FREEZE Shake Model CS700-FG Assembly Correct assembly of the freezer is essential to prevent leakage of the product and damage to the freezer. To assemble the freezer, you will need an approved lubricant (such as Petrol-Gel). Make sure all parts of the assemblies have been washed and sanitized before assembling.
Page 28
ELECTRO FREEZE Shake Model CS700-FG Assembly — continued 6. See figure 7-5 and o-ring chart in the Replacement Parts Section. Install and lubricate the o-rings (4, 5) on the plunger (6). Insert halfway into the head (1), with the rectangular flat side facing the front.
Page 29
ELECTRO FREEZE Shake Model CS700-FG Assembly — continued Important: ALWAYS make sure the head bushing is positioned in the head properly (see Figure 7-4). The head is slotted to match the key on the bushing. Make sure the key aligns with the slot.
ELECTRO FREEZE Shake Model CS700-FG Start-up Instructions Sanitizing The sanitizing instructions explained in Important: this section are procedures to remove Do not insert any tools or objects into bacteria and maintain a clean, sanitary the mix feed port or head dispensing freezer.
ELECTRO FREEZE Shake Model CS700-FG 8.2 Priming Priming the freezer removes all excess air and sanitizer from the freezing cylinder and sets the proper overrun for the first cylinder of product. Always have clean, sanitized hands when handling mix feed tube.
ELECTRO FREEZE Shake Model CS700-FG End of Day Operation 1. In areas where state and local health codes allow and if permitted by the franchise, the product may remain in the freezer. 2. Leave the Selector Switch in the “AUTO” position.
ELECTRO FREEZE Shake Model CS700-FG Draining Product from Freezer NOTE: It is your responsibility to be Place an empty container aware of and conform to the requirements under the dispensing head. Drain the for meeting local, state, and federal laws...
ELECTRO FREEZE Shake Model CS700-FG Product Information 10.1 Overrun As mix is frozen in the freezing cylinder, d. Strike off the excess product so it air is incorporated into the mix to increase is even with the top of the container and its volume, as well as enhance the taste measure the weight.
ELECTRO FREEZE Shake Model CS700-FG Spindle Mixer (Optional) 11.1 Preparation Before use, the spindle shaft, agitator and surrounding surfaces should be washed, rinsed, and sanitized. Follow the procedures for Cleaning & Sanitizing - Spindle Mixer. 11.2 Cleaning and Sanitizing - Spindle Mixer...
ELECTRO FREEZE Shake Model CS700-FG 11.2.2 Daily Sanitizing In a clean container prepare a sanitizing agitator of the spindle mixer, including solution. Sanitizing solution must be the bottom, with sanitizer. Fill a paper mixed according to manufacturer’s cup with sanitizer and immerse agitator instructions to yield 100 PPM strength and spinner shaft in sanitizer.
ELECTRO FREEZE Shake Model CS700-FG Routine Maintenance Electro Freeze recommends the following schedule to help maintain your equipment in like-new operating condition. Take the WEEKLY time to learn and perform these routine procedures and receive in return many years of valuable service from your 1.
Page 38
ELECTRO FREEZE Shake Model CS700-FG Routine Maintenance — continued MONTHLY MONTHLY A. Test Head Switch. B. Air Filter. Clean the air filter with a mild dish The head switch feature is designed detergent solution. to prevent the beater shaft from being accidentally activated.
Page 39
ELECTRO FREEZE Shake Model CS700-FG Routine Maintenance -— continued QUARTERLY ANNUALLY A. Air Condenser. CAUTION Important: To avoid electrical shock or Never use a screwdriver or sharp contact with moving parts, object to clean between fins. make sure all switches are in Both air and water cooled freezers have the “OFF”...
ELECTRO FREEZE Shake Model CS700-FG Routine Maintenance -— continued Winter Storage To protect the unit during seasonal shutdown, it is important to store the CS700 Shake Freezer properly. Please use the following procedures: Disconnect all power to the freezer. Disassemble and wash all parts that come into contact with the mix with a warm, mild detergent solution.
POSSIBILITY OF PERSONAL INJURY. DO NOT ATTEMPT TO CONTINUE UNTIL THE SAFETY PRECAUTIONS ARE THOROUGHLY UNDERSTOOD. CAUTION All maintenance adjustments must be done by an Electro Freeze Distributor or authorized service technician. CAUTION To avoid electrical shock or contact with moving parts, make sure all switches are in the “OFF”...
Page 42
ELECTRO FREEZE Shake Model CS700-FG Troubleshooting Charts — continued PROBLEM PROBABLY CAUSE REMEDY 1. Freezer unplugged. 1. Plug in freezer. Make sure your freezer is connected to a separate circuit independent from any other electrical equipment. Have Fuse blown or breaker tripped at main technician check fuse or breaker disconnect.
ELECTRO FREEZE Shake Model CS700-FG Troubleshooting Charts — continued PROBLEM PROBABLY CAUSE REMEDY See Troubleshooting Table - Product 1. Product too cold. Dispensed product too hard. dispenses slowly out of Have an electrician correct rotation to dispensing 2. Wrong rotation on beater.
Page 44
3. Open starting capacitor or current relay. distributor for service. Contact your Electro Freeze 4. High discharge pressure. distributor for service. NOTE: Contact your authorized Electro Freeze distributor for instructions prior to warranty compressor replacement. QUALITY PARTS PROTECT YOUR EQUIPMENT Keep your freezer in excellent condition.
Page 45
REPLACEMENT PARTS MANUAL with ILLUSTRATIONS COMPACT SERIES uality arts SHAKE FREEZER PROTECT Model CS700-FG YOUR EQUIPMENT 185231-01 2/16 reezer xcellent ondItIon lwAYs ontAct lectro reeze IstrIbutor eplAcement Arts H.C. Duke & Son, LLC. P/N 185231-01 February 2016 Printed in U.S.A.
Page 47
ELECTRO FREEZE Shake Model CS700 Replacement Parts Orders You must have the serial number of your Name: _______________________ freezer when ordering parts — parts may Address:_______________________ differ with a particular serial number of the same model. ______________________________ Parts are listed using terminology that Phone:________________________ best fits the function of the part.
O-RING CHART ELECTRO FREEZE Shake Model CS700-FG Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 185231-01 185231-17...
Page 61
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Bearing-1" Pillow Block ........HC153030 ..2 ..A2T – Bearing-Assy. Rear ..........HC120614 ..1 ..A2T –...
Page 62
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Capacitor-Start (Compressor) ......HC151414 ..1 ..A2T – Capillary-Tube & Strainer ........HC155397 ..1 ..A2T –...
Page 63
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Filter-22x19x3/8 ..........HC155143 ..1 ..A2T – Float-Level Sensor ..........HC161301 ..1 ..A2T –...
Page 64
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Insulator-Switch ..........HC139175 ..1 ..A2T – Keeper-Assy. Spindle ........HC113435 ..1 ..A2T –...
Page 65
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Panel-Assy. Front ..........HC120436 ..1 ..A2T – Panel-Assy. Front ..........HC120610 ..1 ..A2T –...
Page 66
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Screw-SK Set 1/4-20 x 1/4 ZN ......HC160056 ..1 ..A2T –...
Page 67
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Stud-Assy. Cylinder 1-15/16" ......HC114341 ..2 ..A2T – Support-Assy Driptray ........HC120513 ..1 ..A2T –...
Page 68
ELECTRO FREEZE Model CS700-FG Alphabetized Parts List for Model CS700-FG IMPORTANT: All parts shown are for standard models designed for 208-230v/60Hz/1phase. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Trimstrip-Assy..........HC120500 ..1 ..A2T – Trimstrip-Assy..........HC120627 ..1 ..A2T –...