1. Manuals
  2. Brands
  3. ELECTRO FREEZE Manuals
  4. Freezer
  5. FREEDOM 360 Series
  6. Operator's manual

ELECTRO FREEZE FREEDOM 360 Series Operator's Manual

Soft serve twist freezer
Hide thumbs Also See for FREEDOM 360 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's Manual
with Illustrated Parts List
360
º
FREEDOM
Series
Soft Serve Twist Freezer
Model 99T-RMT
P/N 184621 5/09
H.C. Duke & Son, Inc.
P/N 184621 May 2009
Printed In U.S.A.
184621

Advertisement

Table of Contents
loading

Related Manuals for ELECTRO FREEZE FREEDOM 360 Series

Summary of Contents for ELECTRO FREEZE FREEDOM 360 Series

  • Page 1 Operator’s Manual with Illustrated Parts List º FREEDOM Series Soft Serve Twist Freezer Model 99T-RMT P/N 184621 5/09 H.C. Duke & Son, Inc. P/N 184621 May 2009 Printed In U.S.A. 184621...
  • Page 2 Operator’s Manual Electro Freeze Freedom 360° Series Soft Serve Twist Freezer Model 99T-RMT All contents © Copyright 2009 H.C. Duke & Son, Inc., 21 1 6 Eighth Avenue, East Moline, Illinois 61244 184621...
  • Page 3 ELECTRO FREEZE Soft Serve Model 99T-RMT SAFETY FIRST! Follow these four steps to safety ..1. Recognize Safety Information ..Look for this safety alert symbol throughout this manual. When you see this symbol on your freezer or in this manual, be alert to the potential for personal injury .
  • Page 4 DO NOT attempt to repair the freezer until the main power supply has been disconnected. Some freezers have more than one disconnect switch. Contact your local Electro Freeze Distributor for authorized service. 184621...

  • Page 5: Safety Decal Locations

    (The decals on the next page are num- please contact your local authorized bered 1, 2, 3, and 4. Those numbers Electro Freeze Distributor or H. C. Duke correspond to the numbers in the t able & Son, Inc. When ready to order , you below.
  • Page 6 ELECTRO FREEZE Soft Serve Model 99T-RMT Safety Decal Locations Hazardous rotating beater shaft. Do not operate unit with dispense head removed. P/N HC165025 Before removing dispense head: 1. Turn all control switches to "OFF", and 2. Disconnect all power supplies. Unit may have more than one power supply.

  • Page 7: Table Of Contents

    ELECTRO FREEZE Soft Serve Model 99T-RMT Table of Contents Safety First ................... ii Safety Decal Locations ..............iv Part I Introduction ..............Note to Installer ............... 2.1 Uncrating and Inspection ........... 2.2 Installation ..............2.3 Electrical Requirements ..........2.4 Electrical Connections ..........
  • Page 8 ELECTRO FREEZE Soft Serve Model 99T-RMT Table of Contents (continued) Disassembly and Cleaning ..........16 Cleaning Accessories ..........17 Disassembly Instructions ........18 Cleaning Instructions ..........20 6.3.1 Cleaning Shoe ............22 Assembly ..............Start-up Instructions ............28 Sanitizing Instructions ..........28 Priming ..............

  • Page 9: Introduction

    (309) 755-9858 E-mail: Service@hcduke.com Note to Installer This freezer must be installed and serviced by an Electro Freeze Distributor or authorized service technician in accordance with the installation instructions. After installation, the warranty registration card must be completed and returned to validate the warranty.

  • Page 10: Uncrating And Inspection

    ELECTRO FREEZE Soft Serve Model 99T-RMT Uncrating and Inspection CAUTION punctured, note the damage on the Be sure to properly support carrier’s freight bill and notify the the machine when remov- carrier’s local agent immediately. ing bolts and installing legs or casters.

  • Page 11: Electrical Requirements

    ELECTRO FREEZE Soft Serve Model 99T-RMT Installation (continued) 2. Where codes permit, Electro 4. Water cooled models will require Freeze recommends that the freezer be a 3/8 inch MPT water inlet and water installed on casters and have flexible waste connection. The connections are...

  • Page 12: Specifications

    ELECTRO FREEZE Soft Serve Model 99T-RMT Specifications Particulars Always check and verify voltage and amperage on the data plate located on the back panel of each freezer. 99T-RMT Width (in/cm) 24/61 Height (in/cm) 68/173 Depth (in/cm) 30.5/77.5 Weight (lbs/kg) 690/313...

  • Page 13: Reference Information

    ELECTRO FREEZE Soft Serve Model 99T-RMT Reference Information Model Number: ________________ Serial Number: ________________ Electrical Spec: Voltage _________ Phase _______ Hertz __________ Fill in this information as soon as you Maximum Fuse Size: ____________ receive the Electro Freeze 99T-RMT Soft Serve Twist Freezer. The item...

  • Page 14: Part Names And Functions

    ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions Figure 4-1 Head Assembly 184621...
  • Page 15 ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions (continued) The following descriptions apply to figure 4-1. The number preceding the part name corresponds to the number in the figure. HEAD PLUNGER - CENTER Encloses the freezing cylinder and...
  • Page 16 ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions (continued) Figure 4-2 Beater Shaft Assembly 184621...
  • Page 17 ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions (continued) The following descriptions apply to figure 4-1. The number preceding the part name corresponds to the number in the figure. BUSHING - CYLINDER SEAL - ASSY. SHAFT Holds the beater in place at the Seals the opening between the front of the cylinder.
  • Page 18 ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions (continued) Figure 4-3 Mix Transfer System (MTS) 184621...
  • Page 19 ELECTRO FREEZE Soft Serve Model 99T-RMT Part Names and Functions (continued) SUPPORT-ROLLER BEARING COVER-MTS Holds roller assembly in place. Protection against moving parts. Cover must be in place for the SHOE-ROLLER MTS to operate. Provides an opening to insert the mix transer hose.

  • Page 20: Operator Controls And Indicators

    ELECTRO FREEZE Soft Serve Model 99T-RMT Operator Controls and Indicators Figure 5-1 CAUTION The following paragraphs describe the Test operation of the head operator controls and indicators. Refer to switch prior to placing the figure 5-1 for location of these controls freezer in service.

  • Page 21: Day-Night Switch

    ELECTRO FREEZE Soft Serve Model 99T-RMT Operator Controls and Indicators (continued) DAY-NIGHT Switch This two-position switch controls the day b. "NIGHT" (right) — The medium- and night refrigeration modes. temperature thermostat controls the system refrigeration to maintain a mix a. "DAY" (left) — The temperature holding temperature of 40°F (4ºC) or...

  • Page 22: Reset - Overload

    ELECTRO FREEZE Soft Serve Model 99T-RMT Operator Controls and Indicators (continued) Reset — Overload This control protects the beater motor Important: against failure from an overload condi- If the overload trips frequently, your tion by automatically shutting down the freezer should be checked for proper freezer.

  • Page 23: Probe - "Add Mix

    ELECTRO FREEZE Soft Serve Model 99T-RMT Operator Controls and Indicators (continued) Probe - “ADD MIX” ( See Figure 5-2) For the “ADD MIX” indicator light to indicate low mix, the must be installed in the mix tank, with cord attached and plugged into the receptacle located in the back of the cabinet wall.

  • Page 24: Disassembly And Cleaning

    ELECTRO FREEZE Soft Serve Model 99T-RMT Disassembly and Cleaning Safety Information CAUTION To avoid electrical shock or This freezer uses pressure to assure contact with moving parts, consistent product quality. It is important make sure all switches are in for your safety that the freezer is depres- the “OFF”...

  • Page 25: Cleaning Accessories

    ELECTRO FREEZE Soft Serve Model 99T-RMT Cleaning Accessories The following accessories shipped with the freezer are necessary for cleaning, sanitizing, and disassembly/assembly: 1 BRUSH - Cylinder, 4 inch diameter 5 BRUSH - 1/4 inch diameter with an with 36 inch handle: used to clean the overall length of 18-1/2 inches: used cylinder.

  • Page 26: Disassembly Instructions

    ELECTRO FREEZE Soft Serve Model 99T-RMT Disassembly Instructions Figure 6-2 Head Assembly 1. If there is product in the freezer, CAUTION refer to Section 9, Closing Procedures, To avoid electrical shock or 9.2 Draining Product. contact with moving parts, make sure all switches are in 2.
  • Page 27 ELECTRO FREEZE Soft Serve Model 99T-RMT Disassembly Instructions (continued) 11. Remove MTS cover. 12. Remove MTS hose assemblies from the Mix Transfer Systems as follows CUP SEAL (figure 6-4): a. loosen the hand knob, WASHER b. swing back the shoe clamp, O-RING c.

  • Page 28: 6.3 Cleaning Instructions

    ELECTRO FREEZE Soft Serve Model 99T-RMT 6.3 Cleaning Instructions The cleaning instructions explained in CAUTION this section are procedures to remove To prevent bacteria growth, bacteria and maintain a clean, sanitary remove all O-rings when freezer. The freezer must be disas- cleaning.
  • Page 29 ELECTRO FREEZE Soft Serve Model 99T-RMT 6.3 Cleaning Instructions (continued) b. The head plunger openings, center plunger ports, O-ring grooves, dispense nozzle mounting rings, and mix ports, as shown in figure 6-6. c. The shaft cup seals, washers, and O-rings, plunger O-ring grooves and nozzles, as shown in figure 6-7.

  • Page 30: Cleaning Shoe

    ELECTRO FREEZE Soft Serve Model 99T-RMT 6.3.1 Cleaning and Lubricating MTS Assembly Important: NOTE: Clean the shoe weekly or when necessary. Do not interchange the Do not let shoe sit in sanitizing shoe with any other MTS shoes. solution or water. Corrosion will occur in bore.

  • Page 31: Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Assembly Correct assembly of the freezer is essential to prevent leakage of the product and damage to the freezer. To assemble the freezer you will need an approved lubricant (such as Petrol-Gel). Make sure all parts of the assemblies...
  • Page 32 ELECTRO FREEZE Soft Serve Model 99T-RMT Assembly (continued) Figure 7-4 Dispense Head Assembly Important: 6. (Refer to figure 7-4.) Install and ALWAYS make sure the head bushing then lubricate the O-rings (2) on the is positioned in the head properly.
  • Page 33 ELECTRO FREEZE Soft Serve Model 99T-RMT Assembly (continued) Important: Use original Electro Freeze transfer hose only. Your freezer will not operate properly with any other type of hose. Never twist the transfer hose when assembling or installing. Important: Replace transfer hose every 30 days.
  • Page 34 ELECTRO FREEZE Soft Serve Model 99T-RMT Assembly (continued) Figure 7-7 MTS 19. Refer to figure 7-7. Install the 21. Swing the shoe over hose and MTS hose assembly by first placing the tighten the swing clamp hand knob in clamp next to the braided hose, above the...
  • Page 35 ELECTRO FREEZE Soft Serve Model 99T-RMT Assembly (continued) ROLLER BEARING SUPPORT TANK Figure 7-8 MTS 184621...

  • Page 36: Start-Up Instructions

    ELECTRO FREEZE Soft Serve Model 99T-RMT Start-up Instructions CAUTION Mix Transfer System will be pressurized during operation. Make sure all components and fasteners are secure before start-up. Sanitizing Instructions The washing and sanitizing instructions 2. Prepare 2 gallons (7.5 liters) of explained in this manual are important sanitizing solution in each mix container.
  • Page 37 ELECTRO FREEZE Soft Serve Model 99T-RMT 8.1 Sanitizing Instructions (continued) 8. Connect the main power supply 11. Drain the solution from the to the freezer. Turn the MTS switches to cylinders by slowly pulling down on the dispense handles. “ON”. This will push the sanitizer up into the cylinders.

  • Page 38: 8.2 Priming

    ELECTRO FREEZE Soft Serve Model 99T-RMT 8.2 Priming Priming the freezer removes all excess air from the freezing cylinder and set s the proper overrun for the first cylinder of product. 1. Wash and sanitize your hands 9. Close the plungers when pure and forearms with an approved sanitizer.

  • Page 39: Closing Procedures

    ELECTRO FREEZE Soft Serve Model 99T-RMT Closing Procedures Night Switch Operation 1. In areas where health codes 5. Remove serrated nozzles and will allow, the freezer may be switched clean the drip tray assembly and all soiled to night operation which will allow the surfaces with soap and water.

  • Page 40: Draining Product

    ELECTRO FREEZE Soft Serve Model 99T-RMT Draining Product To remove frozen product from the 6. Very slowly dispense the semi- cylinders: frozen product until it quits dispensing. Use this product for making pints, quarts, 1. Place the SELECTOR switches and/or other novelties.
  • Page 41 ELECTRO FREEZE Soft Serve Model 99T-RMT Draining Product (continued) 10. Prepare 2 gallons (7.6 liters) of 14. Place the SELECTOR switches sanitizing solution for each cylinder. in the “CLEAN” position and allow the Sanitizing solution must be mixed beaters to run for 5 minutes.

  • Page 42: Soft Serve Information

    ELECTRO FREEZE Soft Serve Model 99T-RMT Soft Serve Information 10.1 Overrun As mix is frozen in the freezing cylinder, d. Strike off the excess product so it air is incorporated into the mix to in- is even with the top of the container and crease its volume, as well as enhance measure the weight.

  • Page 43: Overrun Adjustment

    ELECTRO FREEZE Soft Serve Model 99T-RMT 10.2 Overrun Adjustment NOTE: Each person who operates The mix will be a factor in determining the freezer should know what over- the amount of overrun you will be able to run is and how to calculate it.

  • Page 44: 11 Routine Maintenance

    ELECTRO FREEZE Soft Serve Model 99T-RMT 11 Routine Maintenance Electro Freeze recommends the following schedule to help maintain your Model 99T-RMT Soft Serve Twist Freezer in like-new operating condition. Take the time to learn and perform these routine procedures and receive in return many years of valuable service from your freezer.
  • Page 45 ELECTRO FREEZE Soft Serve Model 99T-RMT Routine Maintenance (continued) AS NEEDED CAUTION CAUTION To avoid electrical shock or Make sure the freezer is contact with moving parts, depressurized before make sure all switches are in proceeding. the “OFF” position and that the main power supply is disconnected.
  • Page 46 ELECTRO FREEZE Soft Serve Model 99T-RMT Routine Maintenance (continued) MONTHLY B. Water Condenser. A. Test Head Switch. Check the outlet water temperature of The head switch feature is designed to water-cooled condensers at the floor drain. prevent the beater shaft from being Ideal water temperatures should be about accidentally activated.
  • Page 47 ELECTRO FREEZE Soft Serve Model 99T-RMT Routine Maintenance (continued) MONTHLY ( continued) C. MTS Cover Switch (continued) D. Replace the Mix Transfer Hose 4. Look at the MTS rollers; they should NOT be rotating. If they are rotating, turn CAUTION "OFF"...
  • Page 48 ELECTRO FREEZE Soft Serve Model 99T-RMT 11 Routine Maintenance (continued) 1500 HOURS OF ANNUALLY OPERATION OR 6 MONTHS CAUTION To avoid electrical shock or 1. Contact your Electro Freeze contact with moving parts, distributor for the initial oil change of the make sure all switches are in gear reducer.
  • Page 49 Should you have any questions on items that are not included in this maintenance schedule, or problems where service assistance is needed, please contact your local Electro Freeze Distributor or H. C. Duke & Son, Inc., Electro Freeze Service Department for factory service at: Phone:...

  • Page 50: Troubleshooting Table

    THE SAFETY PRECAUTIONS ARE THOROUGHLY UNDERSTOOD. CAUTION All maintenance adjustments must be done by an Electro Freeze Distributor or authorized ser- vice technician. CAUTION To avoid electrical shock or contact with moving parts, make sure all switches are in the “OFF” position and that the main power supply is disconnected.
  • Page 51 ELECTRO FREEZE Soft Serve Model 99T-RMT 12 Troubleshooting Tables (continued) PROBLEM PROBABLE CAUSE REMEDY Unit does not Freezer unplugged. Plug in freezer. operate. Fuse or breaker blown at main Make sure your freezer is connected to disconnect. a separate circuit independent from any other electrical equipment.
  • Page 52 ELECTRO FREEZE Soft Serve Model 99T-RMT Troubleshooting Tables (continued) PROBLEM PROBABLE CAUSE REMEDY Product 1. Pr oduct too cold. Check product temperature. Should be dispenses 18°F (-7.8°C). See Dispensed Product slowly out of Too Cold. dispensing head. Low overrun. Check air meter. If plugged, clean. See MTS Troubleshooting-No Air (Overrun).
  • Page 53 ELECTRO FREEZE Soft Serve Model 99T-RMT 12 Troubleshooting Table (continued) PROBLEM PROBABLE CAUSE REMEDY Freezer runs Plunger switch rod engaged. Close plunger completely. continually and product Plunger not seated in head. Push plunger down. continues to get colder. Plunger switch (side or center) out of Contact your Electro Freeze Distributor adjustment or defective.
  • Page 54 ELECTRO FREEZE Soft Serve Model 99T-RMT Troubleshooting Table (continued) PROBLEM PROBABLE CAUSE REMEDY Compressor Trouble in compressor condensing See Troubleshooting Chart- does not operate circuit. Compressor/Condensing Circuit Section or operates 16.1 improperly. Faulty start capacitor, run capacitor or Contact your Electro Freeze Distributor relay.
  • Page 55 ELECTRO FREEZE Soft Serve Model 99T-RMT Troubleshooting Table (continued) PROBLEM PROBABLE CAUSE REMEDY Compressor and Plunger switch(es) defective or out of Contact your Electro Freeze Distributor beater motor do adjustment. for service. not operate Time delay defective. Contact your Electro Freeze Distributor when for service.
  • Page 56 ELECTRO FREEZE Soft Serve Model 99T-RMT 12.1 Compressor/Condensing Circuit Troubleshooting Tables PROBLEM PROBABLE CAUSE REMEDY Compressor Improperly wired. Contact your Electro Freeze Distributor will not start – for service. hums intermittently Low line voltage. Ask power company to increase voltage...
  • Page 57 Contact your Electro Freeze Distributor for service. Noisy Tubing rattles. Contact your Electro Freeze Distributor compressor. for service. Spring broken internally. Contact your Electro Freeze Distributor for service. NOTE: Contact your authorized Electro Freeze Distributor for in- structions prior to warranty compressor replacement. 184621...
  • Page 58 ELECTRO FREEZE Soft Serve Model 99T-RMT 12.2 Mix Transfer System (MTS) Troubleshooting Tab PROBLEM PROBABLE CAUSE REMEDY Mix leaks out of Transfer hose worn or split. Remove cover, clean inside MTS MTS. around rollers with spray bottle provided. Install new hose. Do not twist hose.
  • Page 59 ELECTRO FREEZE Soft Serve Model 99T-RMT 12.2 Mix Transfer System (MTS) Troubleshooting Tables PROBLEM PROBABLE CAUSE REMEDY Mix pickup tube Defective or missing duckbill valve. Replace duckbill valve. loses prime. Inlet clamp not tight. Tighten clamp. Worn transfer hose. Replace transfer hose.
  • Page 60 Replacement Parts Manual with Illustrations ° FREEDOM Series Soft Serve Twist Freezer Model 99T-RMT 184621-01 5/09 H.C. Duke & Son, Inc. P/N 184621-01 May 2009 Printed in U.S.A.
  • Page 61 The If you require any further assistance, contact illustrations in this section will help you to H.C. Duke & Son, Inc., Electro Freeze as find the correct part number and descrip- follows: tion. The alphabetized parts list can be...

  • Page 62: Figure 1 Head Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 1 Head Assembly Item Part No. Description * ....HC120013 ....Head-Assy.Dispense 1....HC120012 ....Head-Assy. w/actuators 2....HC160501 ....O-Ring (Plunger) 3....HC160583 ....O-Ring (Head) 4....HC137174 ....Plunger-Side Self Dispense 5....

  • Page 63: Figure 2 Beater Shaft Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 2 Beater Shaft Assembly Item Part No. Description 1 ..... HC196085 .... Bushing-Cylinder 2 ..... HC113467 .... Shaft-Assy. Beater 3 ..... HC134966 .... Blade-Scraper 4* .... HC160500 .... O-ring (Seal) 5* .... HC133098 .... Washer-Shaft Seal 6* ....

  • Page 64: Figure 3 Cabinet Parts

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 3 Cabinet Parts Item Part No. Description Item Part No. Description 1 ..HC117443-01 ... Shroud-Assy. Evaporator 9 ... HC119023 ..Cover-Assy. RMT CAB HC150532... Cord-Assy. Male Plug 10 ..HC119995 ..Cover-Assy. Mix Tank HC151105 ...

  • Page 65: Figure 4 Mix Transfer System (Rmt)

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 4 Mix Transfer System — RMT (sheet 1 of 2) Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 184621-01...
  • Page 66 ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 4 Mix Transfer System — RMT (sheet 2 of 2) Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 184621-01...

  • Page 67: Figure 5 Mts-Rmt Hose Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 5 MTS—RMT Hose Assembly Item Part No. Description 1 ....HC138836 ....Hose-Transfer Red Line 2 ....HC199032-01 ..... Duckbill-Inlet RM MTS (V alve) 3 ....HC118765* ....Port-Assy. Inlet Mix/Air 4 ....HC138170-02 ..... Tube-Air 7-1/2 in.(Hose) 5 .............

  • Page 68: Figure 6 Switch Assemblies

    ELECTRO FREEZE Soft Serve Model 99T-RMT Side Assembly Center Assembly HC114176-01 HC114178-01 Figure 6 Switch Assemblies Item Part No. Description 1 ....HC114174 ....Guide-Assy. Push Rod 2 ....HC140701 ....Plate-Switch 3 ....HC150477 ....Switch-Roller Actuator SPDT (Sides) or ....

  • Page 69: Figure 7 Switch Box

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 7 Switch Box (sheet 1 of 2) Detailed Drawing Item #5A and #7A MOV-Assy. MOV Assembly 116188 Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty.
  • Page 70 ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 7 Switch Box (sheet 2 of 2) Item Part No. Description 1 ..HC150380 ..Relay-Flange Base w/Cover 3PDT 2 ..HC150381 ..Relay-Flange Base w/Cover 3 ..HC150294 ..Capacitor-Start (Beater Motor Dual Rated - 1ph only) 4 ..

  • Page 71: Figure 8 Panel Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 8 Panel Assembly (sheet 1 of 2) Hardware for Panels Panel Screw Nut- Spacer Nut-Speed Speed on Frame Dispense HC160076 H C159132 n/ Front HC160076 H C159132 n/ HC159067 Rear HC160048 H C160114 H...
  • Page 72 ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 8 Panel Assembly (sheet 2 of 2) Item Part No. Description 1 .... HC117441 ....Panel-Assy. Front or ... HC120463 ....Panel-Assy. Front Front Cake 24" (Carvel)(Schlotzsky's)(not shown) 2 .... HC139197 ....Panel-Side RH 3 ....

  • Page 73: Figure 9 Upper Side Assembly Views

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 9 Assembly Views (sheet 1 of 2) Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 184621-01...
  • Page 74 ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 9 Assembly Views (sheet 1 of 2) Part No. Description Item Part No. Description 1 ..HC115004 ..Tube-Assy. Drain 14-1/4" 30 ... HC140672 ..Bracket-Condenser Mtg. WC 1A ... HC115004-03 . Tube-Assy. Drain 10-7/16"...

  • Page 75: Figure 10 Gear Reducer

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 10 Gear Reducer Model — HCD920 HC153360 5 - 1 Ratio A Side* HC153361 5 - 1 Ratio B Side* HC116537 ..Kit-Reducer Shaft Seal HCD920..........1 ea. req. HC153072 ..Kit-Gasket Gear Reducer 5/1............. 1 ea. req.

  • Page 76: Figure 11 Mix Feed Seal Assembly

    ELECTRO FREEZE Soft Serve Model 99T-RMT Figure 11 Mix Feed Seal Assembly Item Part No. Description 1 ....HC160320 ....Screw-SKHC #10-24 x 1-3/4 SST 2 ....HC160166 ....Washer-Lock #10 SST 3 ....HC160556 ....Gasket-Mix Joint 4 ....HC139351 ....Collar-Alignment 5 ....

  • Page 77: Accessories

    ELECTRO FREEZE Soft Serve Model 99T-RMT Accessories Part No. Description HC196103 ....Bottle-Wash 500ML (Plunger and MTS) HC158009 ....Brush-4" w/o Handle (Cylinder)(Use with Handle HC158012) HC158037 ....Brush-1/4 Dia x 18-1/2 Overall Length HC158022 ....Brush-1/4 Dia 2LG 6-1/2 Overall Length HC158018 .....
  • Page 78 ELECTRO FREEZE Soft Serve Model 99T-RMT Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 184621-01...
  • Page 79 ELECTRO FREEZE Soft Serve Model 99T-RMT Notes: _____________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty.
  • Page 80 ELECTRO FREEZE Soft Serve Model 99T-RMT Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty. 184621-01...
  • Page 81 ELECTRO FREEZE Soft Serve Model 99T-RMT Notes: _____________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ __________________________________ Use only original or authorized replacement parts with this freezer. Use of unapproved parts will void warranty.
  • Page 82 This instruction sheet is not intended to be used in place of the Operator’s Manual. Use the following information to assist you only after you have read, understood, and are accomplished in the procedures for cleaning and sanitizing detailed in the Electro Freeze freezer Operator’s Manual. DRAINING PRODUCT ASSEMBLY Follow Closing Procedures in Operator’s Manual to remove frozen...
  • Page 83 The product is now ready to serve. Problem? Contact your local authorized distributor or the freezer manufacturer, Electro Freeze Service Department, 2116 Eighth Avenue, East Moline, IL 61244, (309) 755- or FAX (309) 755-9858 4553 ®...
  • Page 84 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Actuator-Assy. Door Switch ......HC118597 ..1..C2N-1028 —...
  • Page 85 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Brush-9/16" w/36" Handle ......... HC158077 ..1 ..C2N-1028 —...
  • Page 86 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Coil-A/B 208-230v (Replacement coil for HC150156 ..
  • Page 87 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Coupling-Assy. 7/8" Drive HC111780 ..2..C2N-1028 —...
  • Page 88 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Decal-Trimstrip (Schlotzsky's) ......HC164185-01 ..1 ..C2N-1028 —...
  • Page 89 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Handle HC136199 ..1..C2N-1028 —...
  • Page 90 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Insert-Assy. Drip Tray ........HC117447 ..1 ..C2N-1028 —...
  • Page 91 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Leg-Assy. 6" ............ HC112978 ..* ..C2N-1028 —...
  • Page 92 NUMBER (FROM – TO) MTS-Assy. (Complete)........HC118751 ..2 ..C2N-1028 — Nameplate-Electro Freeze Large ....... HC165414 ..1 ..C2N-1028 — Nozzle-Serrated ..........HC196185 ..3** ..C2N-1028 — Nut-Assy. Pressure Switch ....... HC116105 ..* ..C2N-1028 —...
  • Page 93 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Panel-Dispense (Standard) ........ HC139194 ..1 ..C2N-1028 —...
  • Page 94 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Relay-Assy. Overload 3 Phase 3.7-12A..... HC118361 ..1 ..C2N-1028 — H2N-3210 Adaptor-Overload Din Rail ......
  • Page 95 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Screw-SKHC #6-32 x 1 BKOZ HC160381 ..
  • Page 96 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Shroud-Assy. Evaporator HC117443-01 ..1 ..C2N-1028 —...
  • Page 97 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Switch-Roller Actuator DPDT HC150478 ..1..C2N-1028 —...
  • Page 98 ELECTRO FREEZE Soft Serve Model 99T-RMT Alphabetized Parts List for Model 99T-RMT Important: All parts shown are for standard models designed for 230V/1PH/ 60HZ or 203–230V/3PH/60HZ. PART PART SERIAL NUMBER DESCRIPTION NUMBER (FROM – TO) Tube-Assy. Suction Cap Drier......HC120123 ..1 ..C2N-1028 —...

This manual is also suitable for:

99t-rmt

Table of Contents