BRP can-am COMMANDER 2017 Series Operator's Manual
  1. Manuals
  2. Brands
  3. BRP Manuals
  4. Offroad Vehicle
  5. can-am COMMANDER 2017 Series
  6. Operator's manual

BRP can-am COMMANDER 2017 Series Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
2017
Operator's
Guide
Includes
Safety, Vehicle
Maintenance Information
and
COMMANDER
TM
Series
WARNING
Read this guide thoroughly. It contains important safety information.
Minimum age: Operator: 16 or older with a valid driver's license. Keep this Operator's Guide in the vehicle.
Original Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the can-am COMMANDER 2017 Series and is the answer not in the manual?

Questions and answers

Related Manuals for BRP can-am COMMANDER 2017 Series

Summary of Contents for BRP can-am COMMANDER 2017 Series

  • Page 1 2017 Operator’s Guide Includes Safety, Vehicle Maintenance Information COMMANDER Series WARNING Read this guide thoroughly. It contains important safety information. Minimum age: Operator: 16 or older with a valid driver's license. Keep this Operator’s Guide in the vehicle. Original Instructions...
  • Page 2 This document contains the trademark of the following company: Visco-Lok is a trademark of GKN Viscodrive GmbH. † 219001679 en JT ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2016 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.

  • Page 3: Foreword

    Can-Am ® side-by-side vehicle. cle and watch the It's backed by the BRP limited warranty Failure to follow the warnings con- and a network of authorized Can-Am tained in this Operator's Guide can dealers ready to provide the parts, ac- result in SERIOUS INJURY or DEATH.

  • Page 4: About This Operator's Guide

    Due to late changes, some differences be- tween the manufactured product and the descriptions and/or specifications in this guide may occur. BRP reserves the right at any time to discontinue or change specifications, designs, fea- tures, models or equipment without incurring any obligation upon itself.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS FOREWORD ................1 Know Before you Go .
  • Page 6 TABLE OF CONTENTS PRIMARY CONTROLS (cont’d) 1) Steering Wheel ............. . . 44 2) Brake Pedal .
  • Page 7 TABLE OF CONTENTS EQUIPMENT (cont’d) 22) 12-Volt Power Outlet ............73 TUNE YOUR RIDE .
  • Page 8 WARRANTY BRP INTERNATIONAL LIMITED WARRANTY: 2017 CAN-AM ® SSV..134 BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE INDEPENDANT STATES AND TURKEY: 2017 ® CAN-AM SSV ..............138 CUSTOMER INFORMATION PRIVACY INFORMATION .
  • Page 9 TABLE OF CONTENTS CONTACT US..............145 North America .
  • Page 10 TABLE OF CONTENTS _______________...

  • Page 11: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...

  • Page 12: General Precautions

    Even if you try to ventilate engine sories that are not approved by BRP. exhaust with fans or open windows Since these changes have not been and doors, carbon monoxide can tested by BRP, they may increase the rapidly reach dangerous levels.

  • Page 13: Safe Operation - Responsibilities

    Even with vehicle safety fea- BRP dealer in a timely manner if you tures (such as protective structure, become aware of any safety related seat belts, side nets) and protective campaigns.

  • Page 14: Riding Carefully

    SAFE OPERATION - RESPONSIBILITIES The passenger must be tall enough – Always be sure there are no obsta- to always be properly seated: back cles or people behind the vehicle against the backrest with seat belt fas- when you operate in reverse. Pay tened, holding both handholds, and attention to blind spots.

  • Page 15: European Community

    SAFE OPERATION - RESPONSIBILITIES European Community – Always follow proper procedures for climbing or going down hills as The following applies only to the Euro- RIDING YOUR VEHI- described in pean Countries where on road usage is subsection. Check the ter- allowed.

  • Page 16: Pre-Ride Inspection

    PRE-RIDE INSPECTION Always inspect and confirm the safe operating condition of your vehicle prior to ride. Always follow the maintenance schedule described in this Operator's Guide. WARNING Perform a pre-ride inspection before each ride to detect any potential prob- lem that could occur during operation. The pre-ride inspection can help you monitor component wear and deterioration before they become a problem.
  • Page 17 PRE-RIDE INSPECTION ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Cargo Load: If you transport a cargo, respect the maximum load capacity of 272 kg (600 lb). Ensure cargo is properly secured to the rear cargo box. Vehicle Load: Ensure that total load on the vehicle (including operator, passenger, cargo, tongue weight and added accessories) does not exceed 363 kg (800 lb).
  • Page 18 PRE-RIDE INSPECTION ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Press down on the brake pedal and make sure you feel Brake pedal firm resistance and that it fully returns to position when released. Fuel level Check the fuel level. Horn Check horn operation.

  • Page 19: Prepare To Ride

    PREPARE TO RIDE Before you Ride Weather conditions should help you decide how to dress. To maximize Perform pre-ride inspection to confirm comfort and avoid frostbites in win- the safe operating condition of your ve- ter, dress for the coldest weather ex- PRE-RIDE INSPECTION hicle.
  • Page 20 PREPARE TO RIDE Use tinted face shields or goggles in crash, good quality protective gear the daytime only; do not use them at made of sturdy material may prevent night or in poor illumination. Do not or reduce injury. use them if they impair your ability to In cool-weather riding, protect your- discern color.

  • Page 21: Avoid Accidents

    AVOID ACCIDENTS Avoid Rollovers and – Never attempt donuts, skids, slides, fishtails, jumps, or other stunts. If Tipovers vehicle starts to skid or slide, steer Side-by-side vehicles handle differ- in the direction of the skid or slide. ently from other vehicles. Side-by-side Never slam the brakes and lock the vehicles are designed to handle wheels.

  • Page 22: Avoid Collisions

    AVOID ACCIDENTS – Never grab the cage while riding. Hands can be crushed between the cage and the ground in a rollover. Keep hands on the steering wheel or handholds. – Never try to stop a rollover using your arms or legs. If you think that the vehicle may tip or roll, the driver should keep both hands on the steering wheel and the left foot...

  • Page 23: Riding Your Vehicle

    RIDING YOUR VEHICLE Practice Exercises U turn Exercises Before you go out for a ride, it is very Practice doing U turns. important to familiarize yourself with – Accelerate slowly and while remain- the handling of your vehicle by prac- ing at low speed, gradually turn the ticing in a controlled environment.

  • Page 24: Off-Road Operation

    RIDING YOUR VEHICLE – Always perform this reverse exer- Whenever there is the slightest doubt cise at slow speeds. that the vehicle can safely negotiate an obstacle or a particular piece of terrain, – Become familiar with the usage of always choose an alternate route.
  • Page 25 RIDING YOUR VEHICLE NOTE: In reverse operation, the en- ilarly so, be watchful of hazards such gine RPM is limited thus limiting the as rocks, logs, etc., partially covered by vehicle reverse speed. vegetation. Riding on Snow or Ice WARNING When performing pre-ride inspection, When driving downhill in reverse, pay special attention to locations on...
  • Page 26 RIDING YOUR VEHICLE keep brake and accelerator pedals and Riding on Gravel, Loose Stones or floor boards free of snow and ice. Fre- Other Slippery Surfaces quently wipe snow off seat, steering Riding on loose stones or gravel is very wheel, headlights and tail lamps.
  • Page 27 RIDING YOUR VEHICLE pery or has too loose a surface, you Side Hilling can lose control. If you go over the Whenever possible, side hilling (driv- top of a hill at high speed, you may not ing across a slope rather than up or have time to prepare for the terrain down it) should be avoided.
  • Page 28 RIDING YOUR VEHICLE club does not exist in your area, help hicle. If you encounter animals on the to start one. Group riding and club ac- trail, stop and observe quietly and with tivities provide a pleasurable, social caution. It will be one of the better experience.

  • Page 29: Moving Loads And Doing Work

    MOVING LOADS AND DOING WORK Working with your Vehicle Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are avail- able from your authorized Can-Am dealer. To prevent possible injury, follow the in- structions and warnings that accompany the accessory.
  • Page 30 MOVING LOADS AND DOING WORK Secure the load to the tie down hooks inside cargo box. Use only the tie down hooks on the bottom of the cargo box; do not secure cargo to the cage or other part of the vehicle. If it is not properly secured, a load may slide or fall off, pos- sibly striking occupants or bystanders;...
  • Page 31 MOVING LOADS AND DOING WORK Operating While Carrying a Load WARNING Reduce your speed when carrying – Keep yourself and others clear cargo and turn gradually. Avoid hills of the cargo box and vehicle and rough terrain. Allow more distance frame junction when lowering for braking.

  • Page 32: Hauling A Load

    Hauling a Load Riding this vehicle with a trailer sub- stantially increases the risk of toppling, NOTICE A BRP approved rear especially on inclined slopes. If a trailer hitch must be properly installed on is used behind the vehicle make sure the vehicle for hauling trailers.
  • Page 33 MOVING LOADS AND DOING WORK MAXIMUM HAULING CAPACITY TRAILER TONGUE TYPE OF LOAD WEIGHT ATTACHMENT ALLOWED ALLOWED 50.8 mm (2 in) x 50.8 mm 270 kg 27 kg (2 in) hitch ball (595 lb) (60 lb) support NOTE: Includes trailer and trailer load. Ensure to properly load the trailer so that tongue is always pushing on hitch support and not pulling on hitch ball.

  • Page 34: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Safety Labels Read and understand all the safety la- bels on your vehicle. These labels are affixed to the vehicle for the safety of the operator, passen- ger or bystanders. The following labels are on your vehi- cle, and they should be considered per- manent parts of the vehicle.
  • Page 35 IMPORTANT ON-PRODUCT LABELS tmo2014-001-007_b TYPICAL ________ ________ SAFETY INFORMATION...
  • Page 36 IMPORTANT ON-PRODUCT LABELS tmo2014-002-006_b TYPICAL _______ ________ SAFETY INFORMATION...
  • Page 37 IMPORTANT ON-PRODUCT LABELS tmo2014-002-005_b TYPICAL tmo2013-001-006_e ________ ________ SAFETY INFORMATION...
  • Page 38 IMPORTANT ON-PRODUCT LABELS tmo2016-001-101_a 704903672 LABEL 1 _______ ________ SAFETY INFORMATION...
  • Page 39 IMPORTANT ON-PRODUCT LABELS Put the Shift Lever to PARK (P) before exiting vehicle. The vehicle can roll if not in PARK. Stop the vehicle and apply the Brake before using the Shift Lever and the 2WD/4WD 704902420C Switch. LABEL 4 Be prepared in case of rollover If the vehicle rolls over, any part of your body (such as arms,...
  • Page 40 IMPORTANT ON-PRODUCT LABELS Be prepared in case of rollover Improperly loading a trailer may cause loss If the vehicle rolls over, any part of control. Evenly balance the load. of your body (such as arms, • Maximum towing weight: 270 kg legs, or head) outside of the cockpit can be crushed by the •...
  • Page 41 IMPORTANT ON-PRODUCT LABELS This warning applies only in European Countries where on road usage is allowed. On Road Use This quadricycle is built for "OFF ROAD" purposes only. It may be used for short distances on paved surfaces at reduced speed, in order to move the vehicle from an off road location to another.
  • Page 42 IMPORTANT ON-PRODUCT LABELS 704902434B LABEL 15 vmo2010-010-100_a LABEL 16 704903434 LABEL 17 Never use the frame near this location to ground any electrical component such as a winch. When in use, the electrical component may induce an undesired power steering signal resulting in an unintended steering input.

  • Page 43: Compliance Labels

    TYPICAL 1. Compliance labels located under glove box BRP certifies that this ROV complies with the American National Standard for Recreational Off-Highway Vehicles, ANSI / ROHVA 1 - 2014 Standard. BRP certifie que ce véhicule récréatif hors-route est conforme à la norme "American National Standard for Recreational Off-Highway Vehicles", ANSI /...
  • Page 44 IMPORTANT ON-PRODUCT LABELS This page is intentionally blank _______ ________ SAFETY INFORMATION...

  • Page 45: Vehicle Information

    VEHICLE INFORMATION _______________...

  • Page 46: Primary Controls

    PRIMARY CONTROLS It is important to know the location and operation of all controls, and to develop and practice smooth and coordinated use of them. NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection.

  • Page 47: Brake Pedal

    PRIMARY CONTROLS CAUTION Under rough trail conditions or when crossing an ob- stacle, the steering wheel could sud- denly jerk on one side, causing hand or wrist injuries if the thumbs are rolled around the steering wheel. Models with DPS The DPS reduces the effort to turn the steering wheel.
  • Page 48 PRIMARY CONTROLS tmo2014-002-011_b 1. Shift lever 2. Park tmo2014-006-004_a 3. Reverse TYPICAL - SHIFT LEVER CAN BE LOCKED IN 4. Neutral PARKED POSITION 5. High range (forward) 1. Shift lever locking key 6. Low range (forward) Two locking keys are supplied with the The vehicle must be stopped and vehicle.
  • Page 49 PRIMARY CONTROLS Low Range (Forward) This position selects the low speed range of the gearbox. It allows the ve- hicle to move slowly with maximum torque at the wheels. NOTICE Use the low speed range to pull a trailer, carry heavy cargo, go over obstacles or drive uphill and downhill.

  • Page 50: Secondary Controls

    SECONDARY CONTROLS NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection. tmo2014-002-002_a TYPICAL 1) Ignition Switch and Keys Ignition Switch The ignition switch is located on the up- per console area.
  • Page 51 SECONDARY CONTROLS ON with Lights WARNING When the key is turned in this position, On steep downhills, the engine the electrical system of the vehicle is speed limiter may not prevent the activated. vehicle from accelerating beyond this speed. The gauge should wake-up. The vehicle lights are turned on.

  • Page 52: Engine Start Button

    SECONDARY CONTROLS 3) Multifunction Lever Digitally Encoded Security System (D.E.S.S.) Low/High Beam Selection The ignition keys contain an electronic circuit that gives it a unique electronic serial number. The D.E.S.S. system reads the key code and allows engine starting for keys it recognizes.

  • Page 53: Hazard Warning Switch

    SECONDARY CONTROLS 4) Hazard Warning Switch tmo2014-002-004_e TYPICAL 1. 2WD/4WD switch tmo2014-002-004_d This switch selects 2 wheel drive or TYPICAL 4 wheel drive mode when the vehicle 1. Hazard warning switch is stopped and the engine is running. The hazard warning switch is located NOTICE vehicle must...

  • Page 54: Sport/Eco Mode Switch

    SECONDARY CONTROLS 6) Sport/ECO Mode Switch The sport/ECO switch is located on the upper console. It is used to select the sport or ECO mode in high range. tmo2014-002-004_h TYPICAL 1. Winch switch GUIDE Refer to your winch included with your vehicle for proper winch op- eration.

  • Page 55: Dps Switch (Models With Dps)

    SECONDARY CONTROLS 9) DPS Switch (Models WARNING with DPS) Only use the override to help get The DPS switch is used to change the the vehicle unstuck from mud or DPS (Dynamic Power Steering) mode. other soft terrain. Do not use the override for normal operation in To change mode, DPS switch needs to reverse.

  • Page 56: Shift Lever Lock

    SECONDARY CONTROLS 10) Shift Lever Lock The shift lever can be locked when the vehicle is parked and left unattended. To unlock shift lever, turn key clock- wise. To lock shift lever, turn key counter- clockwise. tmo2014-006-004_a TYPICAL - SHIFT LEVER CAN BE LOCKED IN PARKED POSITION 1.

  • Page 57: Multifunction Gauge (Lcd) (Dps Model Only)

    MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) The multifunction gauge (LCD) is lo- cated on the steering column. WARNING Do not adjust the display while rid- ing . You could lose control. Multifunction Gauge tmo2011-001-702_d Description 1. Transmission position DISPLAY FUNCTION Park Reverse Neutral...

  • Page 58: Multifunction Gauge Modes

    MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) 5) 4WD Indicator Lamp 10) Seat Belt Indicator Lamp When this indicator is ON, it indicates When this indicator is ON, the driver's the 4WD system is activated. seat belt is not buckled. 6) Low Fuel Level Indicator Lamp 11) Sport Mode Indicator Lamp When this indicator is ON, it indi- When this indicator is ON, the sport...
  • Page 59 MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) GAUGE SETUP Refer to to set current time. Trip Meter (TP) The trip meter records the travelled distance since it has been reset. Dis- tance travelled is displayed either in vdd2008-001-089 kilometers or miles. Combined Mode In this mode, the main screen shows the speed of the vehicle and the engine...
  • Page 60 MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) vsi2009-018-033 Message Display Mode Important messages can be displayed in the main screen. Refer to table below. If an abnormal engine condition occurs, a message can be combined with a pilot TROUBLESHOOTING lamp. Refer to section for details.

  • Page 61: Fault Code Mode

    MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) To erase the MAINTENANCE RE- 4. Press the selector button again, this QUIRED message, proceed as fol- time for 2 seconds. lows: This will change the Mode to either 1. Select PARK. Speed, RPM or Combined. 2.

  • Page 62: Gauge Setup

    MULTIFUNCTION GAUGE (LCD) (DPS MODEL ONLY) Gauge Setup Unit Selection (km/h vs MPH) The speedometer, odometer and trip Clock Setting meter are factory preset in miles but Once clock display as been selected, it is possible to change them to kilo- meter reading.

  • Page 63: Multifunction Gauge (Analog/Digital) (Xt Models)

    MULTIFUNCTION GAUGE (ANALOG/DIGITAL) (XT MODELS) Multifunction Gauge Description The Multifunction Gauge (Analog/digital) is located on the steering column. The Multifunction Gauge (Analog/digital) is comprised of a digital gauge and two analog gauges (speedometer and tachometer). The engine temperature and fuel level bar graphs are comprised in the digital gauge.
  • Page 64 MULTIFUNCTION GAUGE (ANALOG/DIGITAL) (XT MODELS) 1) Analog Speedometer Measures vehicle speed in km/h or mph. 2) MODE (M) Button Pressing the MODE (M) button will scroll through the functions of the main digital display. FUNCTION SEQUENCE OPTIONS Press SET (S) to scroll and select desired Numerical Display is flashing function and press MODE (M) to confirm Press SET (S) to scroll and select desired...
  • Page 65 MULTIFUNCTION GAUGE (ANALOG/DIGITAL) (XT MODELS) 4) Analog Tachometer (RPM) Measures engine revolutions per minute (RPM). Multiply by 1000 to obtain actual revolutions. 5) Indicator Lamps Indicator lamps will inform you of various conditions or problems. An indicator lamp can flash alone or in combination with another lamp. INDICATOR LAMP(S) DESCRIPTION All indicator lamps are activated when ignition...
  • Page 66 MULTIFUNCTION GAUGE (ANALOG/DIGITAL) (XT MODELS) Important messages can also be displayed. Refer to table below. If an abnormal engine condition occurs, a message can be combined with a pilot TROUBLESHOOTING lamp. Refer to section for details. MESSAGE DESCRIPTION Message displayed when the brakes are applied continuously for BRAKE 15 seconds.

  • Page 67: Gauge Setup

    MULTIFUNCTION GAUGE (ANALOG/DIGITAL) (XT MODELS) NOTE: Do not turn ignition switch to 5. Press SET (S) button to change ON before the multifunction gauge hours. turns off. 6. Press MODE (M) button to switch to minutes (minutes flash). 8) Fuel Level Indicator 7.

  • Page 68: Equipment

    EQUIPMENT NOTE: Some vehicle safety labels are not shown on illustrations. For information VEHICLE SAFETY LABELS on vehicle safety labels, refer to subsection. tmo2014-002-009_d TYPICAL tmo2014-002-010_c TYPICAL ______________...

  • Page 69: Tilt Steering

    EQUIPMENT tmo2014-002-008_c TYPICAL 1) Tilt Steering 2) Cup Holders The steering wheel height is ad- Two cup holders are located at the rear justable. of the lower console. Adjust the steering wheel height to face your chest, not your head. To adjust steering wheel height: 1.

  • Page 70: Passenger Handholds

    EQUIPMENT 3) Passenger Handholds The passenger has access to a front handhold located in front of seat above glove box. A left hand handhold located in the cen- ter of the vehicle on the lower console is also accessible. tmo2014-001-015_a 1.

  • Page 71: Shoulder Guards

    EQUIPMENT 9) Seat Belts This vehicle is equipped with 3-point seat belts to help protect driver and passenger in the event of collisions, rollovers or tipovers to help keep driver and passenger in the cockpit. WARNING Wear seat belts properly at all times.

  • Page 72: Driver's Seat

    EQUIPMENT 11) Passenger Seat Position the belt as low as possible across your hips. Then, pull the belt The passenger seat is not adjustable. against your shoulder for a snug fit. The passenger seat can be tilted for- NOTE: Slide the latch as required to ward for removal by releasing the latch adjust the seat belt.

  • Page 73: Central Mirror

    EQUIPMENT NOTE: Using the winch intensively The mirror can be adjusted to suit over a long period of time may dis- driver's preference. charge the battery. WARNING The following tips will help to reduce the risk of discharging the battery: Do not adjust mirror while riding.

  • Page 74: Cargo Box Tilt Release Handles

    EQUIPMENT CARRYING LOADS Refer to in the SAFETY INFORMATION section. 18) Anchoring Hooks To provide anchoring point in order to secure cargo inside the cargo box, 4 anchoring hooks are located inside the cargo area. tmo2011-001-013_a 19) Upper Tailgate 1. Increased cargo volume 2.

  • Page 75: Lower Tailgate

    EQUIPMENT tmo2011-001-318_a TYPICAL 1. Lower tailgate 2. Lower section NOTICE Do not exceed 100 kg tmo2011-001-016_a (220 lb) of weight on the lower tail- TYPICAL 1. Upper tailgate hinge gate during loading or unloading. Always close the lower tailgate be- 20) Lower Tailgate fore operating to reduce the risk of loss of load.
  • Page 76 EQUIPMENT tmo2014-002-004_c 1. 12 V power outlet Remove protective cap to use Do not exceed the rating capacity. Re- SPECIFICATIONS fer to subsection. ______________...

  • Page 77: Tune Your Ride

    TUNE YOUR RIDE Suspension Adjustment REAR SUSPENSION FACTORY SETTINGS Guidelines Your vehicle handling and comfort de- FACTORY ADJUSTMENT pend upon suspension adjustments. SETTING Cam position 1 WARNING Spring preload (soft) Suspension adjustment could af- fect vehicle handling. Always take Suspension Adjustments time to familiarize yourself with the vehicle's behavior after any Spring Preload Adjustment...

  • Page 78: Dps Function

    TUNE YOUR RIDE tmo2011-001-065_a TYPICAL 1. Turn adjusting cams 2. Smooth adjustment 3. Hard adjustment tmo2014-002-004_g 1. DPS switch DPS Function 2. Check the multifunction gauge to The applicable models are equipped confirm the active DPS mode. with a Dynamic Power Steering (DPS) system.
  • Page 79 TUNE YOUR RIDE To change the DPS mode, proceed as follows: 1. Press and hold DPS switch for 2 seconds to go to the next setting. 2. Release DPS switch. 3. Repeat until desired setting is se- lected. NOTE: The DPS adjustment will not be possible if the vehicle transmission is set to REVERSE.

  • Page 80: Fuel

    FUEL Fuel Requirements Vehicle Fueling Procedure NOTICE Always use fresh gaso- WARNING line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- – Fuel is flammable and explosive pounds, and the production of gum under certain conditions. and varnish deposits which can –...

  • Page 81: Fueling A Gasoline Container

    FUEL WARNING If a differential pressure condition is noticed (whistling sound heard when loosening fuel reservoir cap) have vehicle inspected and/or re- paired before further operation. 4. Insert the spout into the filler neck. 5. Pour fuel slowly so that air can es- cape from the tank and prevent fuel flow back.

  • Page 82: Break-In Period

    BREAK-IN PERIOD Operation During Break-In A break-in period of 300 km (200 mi) or 10 operating hours is required for the vehicle. Engine During the break-in period: – Avoid full throttle operation. – Avoid pressing accelerator pedal more than 3/4 of the stroke. –...

  • Page 83: Basic Procedures

    BASIC PROCEDURES Starting the Engine – 4x4 applications – Mud holes Insert key in ignition switch and turn to the ON with lights position. – Water holes – Crossing obstacles Press the brake pedal. – Climbing onto trailer NOTE: If shift lever is not set to PARK –...

  • Page 84: Stopping The Engine And Parking The Vehicle

    Always put the vehicle in PARK If riding in any of the conditions listed when stopped or parked to pre- below, BRP highly recommends not to vent rolling. constantly hold the throttle wide open (WOT) for more than five (5) minutes.
  • Page 85 BASIC PROCEDURES For more tips for maximizing the drive CHOOSING belt durability, refer to THE CORRECT RANGE (LOW OR HIGH) _______________...

  • Page 86: Special Procedures

    SPECIAL PROCEDURES What to do if Water is What to do if Battery is Suspected to be in the CVT Drained out If water is present in the CVT, the en- The vehicle can be jump started by us- gine will accelerate but the vehicle will ing the red (+) cable to the battery pos- remain still.

  • Page 87: Transporting The Vehicle

    TRANSPORTING THE VEHICLE If your vehicle needs to be transported, 7. Firmly attach the rear wheels it should be carried on a flatbed trailer tie-down straps to both sides of the of the proper size and capacity. rear of the trailer with ratchets. 8.

  • Page 88: Lifting And Supporting The Vehicle

    LIFTING AND SUPPORTING THE VEHICLE Front of Vehicle Place vehicle on a flat non slippery ground. Ensure vehicle shift lever is set to PARK. Install an hydraulic jack under front skid plate. Lift front of vehicle and install a jack stand on each side under frame sec- tion in front of the lip for center skid plate.

  • Page 89: Maintenance

    MAINTENANCE _______________...

  • Page 90: Maintenance Schedule

    MAINTENANCE SCHEDULE Maintenance is very important for keeping your vehicle in safe operating condition. Proper maintenance is the owner's responsibility. The vehicle should be serviced as per the maintenance schedule. The following message appears in the gauge after every 50 hours of operation, to remind you of maintenance requirements: MAINTENANCE REQUIRED.
  • Page 91 MAINTENANCE SCHEDULE EVERY 1 500 KM (1,000 MI) OR 50 HOURS (whichever comes first) EVERY 750 KM (500 MI) OR 25 HOURS (whichever comes first) Inspect the drive shaft boots and protectors Inspect brake pads. Replace as needed Inspect wheel bearings for abnormal play Clean exhaust area Tighten beadlock screws (if equipped) Inspect and clean CVT air filters (service more often in dusty conditions)
  • Page 92 MAINTENANCE SCHEDULE PERFORM AT THE FIRST 3 000 KM (2,000 MI)AND AT 6 000 KM (4,000 MI) THEN FOLLOW THE REGULAR SCHEDULE PERFORM AT THE FIRST 1 500 KM (1,000 MI) AND AT 3 000 KM (2,000 MI) THEN FOLLOW THE REGULAR SCHEDULE Replace gearbox oil Clean the vehicle speed sensor (VSS) EVERY 6 000 KM (4,000 MI) OR 200 HOURS (whichever comes first)

  • Page 93: Maintenance Procedures

    MAINTENANCE PROCEDURES This section includes instructions for – Riding on dry dirt covered surfaces. basic maintenance procedures. If you – Riding on dry gravel trails or similar have the necessary mechanical skills conditions. and the required tools, you can per- –...
  • Page 94 MAINTENANCE PROCEDURES tmo2011-001-087_a 1. Engine air filter tbs2011-009-007_a Engine Air Filter Housing Cleaning DRAIN PLUG ACCESS FROM LH SIDE OF VEHICLE 1. If there is water in the first air cham- 1. Remove drain plug to expel water ber, remove the drain plug, from un- derneath to expel water.

  • Page 95: Front Grill Kit

    MAINTENANCE PROCEDURES tbs2011-009-001 tbs2011-009-002_b 3. Verify that the cover fits well on the Engine Air Filter Cleaning engine air filter housing before clos- Clean engine air filter by tapping out ing clamps. heavy dust from paper element, this will allow dirt and dust to get out of the paper filter.

  • Page 96: Cvt Air Filter

    MAINTENANCE PROCEDURES tmo2011-001-080_a 1. CVT air filter plastic cover 2. Slide the cover rearward. tmo2014-001-008_a FRONT OF VEHICLE - COMPONENTS REMOVED FOR CLARITY 1. Front grill kit 2. Clean front grill kit with water. CVT Air Filter CVT air filter inspection and cleaning frequency should be adjusted accord- ing to riding conditions as it is critical to ensure proper engine performance...

  • Page 97: Engine Oil

    MAINTENANCE PROCEDURES With vehicle on a level surface and en- gine cold, check the oil level as follows: 1. Unscrew dipstick then remove it and wipe clean. tmo2013-003-050_a 1. CVT air filter 2. Clean filter, using soft soap and wa- ter, then water rinse.

  • Page 98: Oil Filter

    Damages caused by the of debris gives an indication of internal use of oil not suitable for this engine engine damage. will not be covered by the BRP lim- Install a NEW gasket ring on the drain ited warranty. plug.

  • Page 99: Radiator

    MAINTENANCE PROCEDURES Oil Filter Removal Clean oil filter area. Remove oil filter cover screws. Remove oil filter cover. Remove oil filter. vmr2006-008-001_a 1. Slightly oil 2. Slightly oil Install the cover on the engine. Tighten oil filter cover screws to rec- ommended torque.

  • Page 100: Engine Coolant

    MAINTENANCE PROCEDURES If available, use a garden hose to rinse the radiating fins. CAUTION Never clean radiator with your hands when it is hot. Let the radiator cool down before clean- ing. NOTICE Be careful not to damage the radiating fins when cleaning. Do not use any object/tool that could damage the fins.
  • Page 101 MAINTENANCE PROCEDURES NOTICE Always use ethylene-gly- col antifreeze containing corrosion inhibitors specifically for internal combustion aluminum engines. Engine Coolant Replacement Cooling System Draining WARNING In order to avoid potential burns, do not remove the pressure cap or loosen the coolant drain plug if the engine is hot.
  • Page 102 MAINTENANCE PROCEDURES tmo2015-001-303_a 1. Cooling system drain plug access tmr2011-011-029_a NOTE: Do not unscrew the coolant 1. Hose clamp position to note drain plug completely. 2. Lower radiator hose to remove 5. Drain cooling system completely. 6. Reinstall cooling system drain plug. TORQUE Cooling system 9 N•m to 11 N•m...
  • Page 103 MAINTENANCE PROCEDURES All Models 3. Remove the pressure cap. 4. Fill the cooling system until coolant comes out of the bleed screw(s). 5. Install the bleed screw(s) using NEW gasket rings and torque as per following chart. TORQUE 4.4 N•m to 5.6 N•m Gasket ring (39 lbf•in to 50 lbf•in) tmo2011-001-094_a...

  • Page 104: Muffler Spark Arrester

    MAINTENANCE PROCEDURES tmr2011-011-025_a ENTIRE FRONT END LIFTED tmr2011-011-028_a 1. Ground level 1. Cooling system refill adapter A. 60 cm (24 in) 2. Expansion tank hose 3. Coolant system full level (pressure cap seat) 9. Lower vehicle to the ground. 15. Install the pressure cap. 10.
  • Page 105 MAINTENANCE PROCEDURES Remove the muffler cover. tmo2011-001-041_a 1. Spark arrester 2. Gasket 3. Exhaust tail pipe tmo2011-001-040_a 1. Muffler cover Remove carbon deposits from the 2. Exhaust tail pipe spark arrester using a brush. Remove and discard the tail pipe retain- NOTICE Use a soft brush and be ing screws.

  • Page 106: Gearbox Oil

    Use ONLY the recom- lated to meet the lubrication require- mended type of oil. ments of this gearbox. BRP strongly recommends the use of its XPS oil. The oil should be level with the bottom However, if the XPS synthetic gear oil of the oil level orifice.

  • Page 107: Spark Plugs

    MAINTENANCE PROCEDURES Wipe off any spillage. Spark Plugs Access to Spark Plugs 1. Remove both seats. 2. Remove upper console retaining screws and plastic rivets. 3. Slightly lift upper console to allow removal of lower console. 4. Remove lower console plastic riv- tmo2011-001-111_a ets.

  • Page 108: Cvt Cover Installation

    MAINTENANCE PROCEDURES CVT Cover Removal WARNING Remove the thirteen CVT cover Never touch CVT while engine is screws. running. Never drive vehicle when CVT cover is removed. NOTE: The four CVT cover lower screws are accessible through the square holes in the central skid plate. WARNING Engine must be cool before cover is removed.

  • Page 109: Drive Belt

    MAINTENANCE PROCEDURES Vmr2012-018-005_a Vmr2012-018-003_a TYPICAL CVT COVER TIGHTENING SEQUENCE 1. Puller/locking tool 2. Fixed sheave of driven pulley CVT COVER SCREWS To remove belt, slip the belt over the Tightening 7 N•m ± 0.8 N•m top edge of fixed sheave, as shown. torque (62 lbf•in ±...

  • Page 110: Exhaust Area

    MAINTENANCE PROCEDURES Exhaust Area Cleaning WARNING Engine and exhaust must be cool before removing debris. Always wear protective gloves when re- moving debris. 1. Wearing gloves, hand remove all ex- vmr2007-051-006_a cess debris around exhaust. 1. Arrow printed on belt 2.

  • Page 111: Fuses

    MAINTENANCE PROCEDURES NOTICE Remove battery holder retaining Do not use a higher rated screw. fuse as this can cause severe dam- age. Fuse Box Location The vehicle is equipped with two fuse boxes. They are both located under the console on the driver's side next to the battery.

  • Page 112: Lights

    MAINTENANCE PROCEDURES Fuse Box Description FUSE IN FUSE BOX 3 MAIN FUSE BOX Dynamic power steering (DPS) (Models 40 A DESCRIPTION RATING with DPS) Fan relay Lights Main relay Always check light operation after re- Accessories relay placement. Light relay Headlight and Front Turn Signal Brake relay Bulb Replacement...
  • Page 113 MAINTENANCE PROCEDURES tmo2011-001-113_a vmr2007-050-007_a 1. Adjustment screws TYPICAL Pull out bulb. Taillight and Rear Turn Signal Bulbs Replacement Open upper tailgate. Remove both taillight retaining screws. tmo2011-001-114_a 1. Light bulb socket 2. Light bulb Properly reinstall removed parts in the reverse order of their removal.

  • Page 114: Drive Shaft Boot And Protector

    MAINTENANCE PROCEDURES tmo2011-001-129_a FRONT OF VEHICLE 1. Radiator tmo2011-001-116_a 2. Inner drive shaft boots 1. Tail light 2. Light bulb and socket Push the bulb in and hold while turning counterclockwise to release. Installation is the reverse of the re- moval procedure.

  • Page 115: Tightening Rear Stabilizer Bar Bolts

    MAINTENANCE PROCEDURES tmo2011-001-127_a tmo2011-001-131_a REAR OF VEHICLE TYPICAL 1. Outer drive shaft boot Wheels and Tires Tightening Rear Stabilizer Bar Bolts Wheel Removal Torque retaining screws of stabilizer Loosen nuts then lift and support vehi- bar according to the following se- LIFTING AND SUPPORT- cle.
  • Page 116 MAINTENANCE PROCEDURES TIRE PRESSURE FRONT REAR 69 kPa 83 kPa MIN. (10 PSI) (12 PSI) MAX. (Use when 83 kPa 152 kPa total load is greater (12 PSI) (22 PSI) than 180 kg (400 lb)) NOTE: Although the tires are specif- ically designed for off-road use, a flat may still occur.

  • Page 117: Suspensions

    MAINTENANCE PROCEDURES Suspensions Front Suspension Lubrication Use SUSPENSION GREASE (P/N 293 550 033) or an equivalent. Lubricate front A-arms. There are three grease fittings on each A-arm oriented downwards. tmo2011-001-083_a TYPICAL 1. MIN 2. MAX NOTE: A low level may indicate leaks or worn brake pads.

  • Page 118: Seat Belts

    MAINTENANCE PROCEDURES WARNING The brake fluid replacement or brake system maintenance and repairs should be performed by an authorized Can-Am dealer. Seat Belts Seat Belt Cleaning To clean dirt and debris from the seat belts, sponge the straps with mild soap and water.

  • Page 119: Vehicle Care

    VEHICLE CARE Post-Operation Care When vehicle is used in salt-water environment rinsing the vehicle with fresh water is necessary to preserve vehicle and its components. Metal- lic parts lubrication is highly recom- mended. Use XPS LUBE (P/N 293 600 016) or an equivalent. This must be performed at the end of each operat- ing day.

  • Page 120: Storage And Preseason Preparation

    STORAGE AND PRESEASON PREPARATION When a vehicle is not in use for more than 4 months, proper storage is a ne- cessity. When using your vehicle after storage, a preparation is required. See an authorized Can-Am dealer to have your vehicle prepared for either storage or the preseason.

  • Page 121: Technical Information

    TECHNICAL INFORMATION ______________...

  • Page 122: Vehicle Identification

    These numbers are required by the authorized Can-Am dealer to com- plete warranty claims properly. No warranty will be allowed by BRP Inc. if the engine identification number (EIN) or vehicle identification number (VIN) is removed or mutilated in any way.

  • Page 123: Ec Declaration Of Conformity

    The EC-Declaration of Conformity does not appear in this version of the Operator's Guide. Please refer to the printed version that was delivered with your vehicle. ddd2009-001...

  • Page 124: Specifications

    Spark arrestor approved by USDA Forest Service Engine air filter Synthetic paper filter LUBRICATION SYSTEM Type Wet sump. Replaceable oil filter BRP Rotax ® paper type, replaceable Oil filter Capacity 2 L (2.1 qt (U.S. liq.)) (oil change with filter)
  • Page 125 SPECIFICATIONS 1000 MODEL 800R ELECTRICAL SYSTEM Magneto generator output 625 W @ 6000 RPM Ignition system type IDI (Inductive Discharge Ignition) Ignition timing Not adjustable Quantity Spark plug Make and type NGK DCPR8E 0.7 mm to 0.8 mm (.028 in to .031 in) Engine RPM limiter setting 8000 RPM Type...
  • Page 126 SPECIFICATIONS 1000 MODEL 800R ELECTRICAL SYSTEM (cont'd) Accessories 15 A Fuses (cont'd) Fuel pump FUEL SYSTEM Fuel delivery Type Electronic fuel injection (EFI) with iTC Throttle body 54 mm with ETA Fuel pump Type Electric (in fuel tank) Idle speed 1250 ±...
  • Page 127 SPECIFICATIONS 1000 MODEL 800R FRONT SUSPENSION (cont'd) Suspension travel 254 mm (10 in) Shock absorber Type Oil / 5 spring preload settings REAR SUSPENSION Torsional Trailing arm Independant (TTI) with Suspension type external stabilizer bar Preload adjustment type 5 positions cam Suspension travel 254 mm (10 in) Shock absorber...
  • Page 128 SPECIFICATIONS 1000 MODEL 800R WHEELS Type Cast Aluminum Front 14 x 7 (in) Rim size Rear 14 x 8.5 (in) Wheel nuts torque 100 N•m ± 10 N•m (74 lbf•ft ± 7 lbf•ft) CHASSIS 50 mm (2 in) diameter, high strength steel, Cage type ROPS-approved cage DIMENSIONS...

  • Page 129: Troubleshooting

    TROUBLESHOOTING ______________...

  • Page 130: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES CVT BELT IS SLIPPING 1. Water has entered in the CVT. – Refer to SPECIAL PROCEDURES subsection. E IS DISPLAYED ON TRANSMISSION POSITION DISPLAY 1. Shift lever is between 2 positions. – Properly position the shift lever in the desired position. 2.
  • Page 131 TROUBLESHOOTING GUIDELINES ENGINE TURNS OVER BUT FAILS TO START 1. Flooded engine (spark plug wet when removed). – (If the engine does not start and it is fuel-flooded, the drowned mode can be activated to prevent fuel injection and to cut ignition while cranking. Proceed as follows: •...
  • Page 132 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 7. Engine is in limp home mode. – Check multifunction gauge display for messages. – Multifunction gauge CHECK ENGINE indicator lamp is on and display shows LIMP HOME, contact an authorized Can-Am dealer. ENGINE OVERHEATS 1.

  • Page 133: Messages In Multifunction Gauge

    MESSAGES IN MULTIFUNCTION GAUGE If an abnormal engine condition occurs, the following messages can be combined with a pilot lamp. MESSAGE DESCRIPTION D.E.S.S. KEY NOT D.E.S.S. key requires cleaning. RECOGNIZED Wrong key used in the ignition switch. Use the right key for BAD KEY the vehicle.
  • Page 134 MESSAGES IN MULTIFUNCTION GAUGE This page is intentionally blank ______________...

  • Page 135: Warranty

    WARRANTY ______________...

  • Page 136: Brp International Limited Warranty: 2017 Can-Am Ssv

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 137 – Damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by BRP or resulting from repairs done by a person that is not an authorized servicing Can-Am SSV Distributor/Dealer;...
  • Page 138 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 139 Can-Am SSV Distributor/Dealer's service manager or owner. If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide.

  • Page 140: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independant States And Turkey: 2017 Can-Am Ssv

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 141 Operator's Guide; – Damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by BRP or resulting from repairs done by a person that is not an authorized servicing Can-Am SSV Distributor/Dealer;...
  • Page 142 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 143 Can-Am SSV Distributor/Dealer's service manager or owner. If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide.
  • Page 144 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.

  • Page 145: Customer Information

    CUSTOMER INFORMATION ______________...

  • Page 146: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.
  • Page 147 CONTACT US Oceania www.brp.com 6 Lord Street North America Lakes Business Park Botany, NSW 2019 565 de la Montagne Street Australia Valcourt (Québec) J0E 2L0 Canada South America Sturtevant, Wisconsin, U.S.A. 10101 Science Drive Rodovia Anhanguera Km 104 Sturtevant, Wisconsin...
  • Page 148 Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the vehicle owner if necessary, like when safety recalls are initiated. It is the owner’s responsibility to notify BRP.
  • Page 149 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 150 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 151 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 152 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 153 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 154 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 155 GUIDE DU CONDUCTEUR Séries COMMANDER / ANGLAIS FAIT AU / MADE IN CANADA U/M:P.C. ®™ AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2016 BOMBARDIER RECREATIONAL PRODUCTS INC. ALL RIGHTS RESERVED. PRINTED IN CANADA.

This manual is also suitable for:

Can-am commander 800r 2017Can-am commander 1000 2017

Table of Contents

Save PDF