Table of Contents

Advertisement

MAVERICK
TM
MAVERICK
TM
OPERATOR'S
GUIDE
Read this guide thoroughly. It contains important safety information.
Minimum age: Operator: 16 or older with a valid driver's license. Keep this Operator's Guide in the vehicle.
The removal or modification of evaporative emission-related parts on this OHRV is illegal.
Violators may be subject to civil and/or criminal penalties under California and federal law.
2 1 9 0 0 2 1 3 0
Trail T and
Sport T
Series
WARNING
Original Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Can-am MAVERICK Trail T Series and is the answer not in the manual?

Questions and answers

Summary of Contents for BRP Can-am MAVERICK Trail T Series

  • Page 1 MAVERICK Trail T and MAVERICK Sport T Series OPERATOR’S GUIDE WARNING Read this guide thoroughly. It contains important safety information. Minimum age: Operator: 16 or older with a valid driver's license. Keep this Operator’s Guide in the vehicle. The removal or modification of evaporative emission-related parts on this OHRV is illegal. Violators may be subject to civil and/or criminal penalties under California and federal law.
  • Page 2 – Visco-Lok is a trademark of GKN Viscodrive GmbH. † 219002130 en COJT ®™ and the BRP logo are trademarks of Bombardier Recreational Products Inc. or its affiliates. ©2020 Bombardier Recreational Products Inc. and BRP US Inc. All rights reserved.
  • Page 3: Vehicle Identification

    Can-Am dealer to A-2: XXX kg complete warranty claims properly. A-3: XXX kg No warranty will be allowed by BRP if the engine identification number (EIN) or vehicle identification number (VIN) is removed, mutilated or altered in any...
  • Page 4: Vehicle Identification Form

    VEHICLE IDENTIFICATION Vehicle Identification Form Please verify with your dealer to ensure your vehicle has been registered with BRP. _______________...
  • Page 5: Engine Identification Number

    VEHICLE IDENTIFICATION Engine Identification Number 219002040-012 TYPICAL Rotax XXXX NRSC G1 CO2 g/kWh: MXXXXXXX tmo2011-001-401_a Production date: MM-YYYY TYPICAL — ENGINE SERIAL NUMBER Family type: XXXXXX LABEL AT1/P V-#### 1. EIN (Engine Identification Number) EN-704908639-DEC Compliance Label TYPICAL NRMM IDENTIFICATION LABEL NOTE: Tampering with the engine Regulation (EU) 2016/1628 or its components voids the EU...
  • Page 6: Foreword

    Este manual pode estar disponível em seu idioma. Fale com sua Português concessionária ou visite o site: www.operatorsguides.brp.com Воспользуйтесь руководством на вашем языке . Узнайте Русский о его наличии у дилера или на странице по адресу...
  • Page 7: Know Before You Go

    Can-Am ® side-by-side vehicle. ardous situation which, if not It's backed by the BRP limited warranty avoided, could result in minor or and a network of authorized Can-Am moderate injury. dealers ready to provide the parts, ac- cessories or service you may require.
  • Page 8: Table Of Contents

    TABLE OF CONTENTS VEHICLE IDENTIFICATION ............1 Vehicle Identification Number.
  • Page 9 TABLE OF CONTENTS IMPORTANT ON-PRODUCT LABELS ..........43 Hang Tag .
  • Page 10 TABLE OF CONTENTS EQUIPMENT (cont’d) 14) Anchoring Hooks............79 15) Trailer Hitch .
  • Page 11 TABLE OF CONTENTS MAINTENANCE PROCEDURES ..........102 Accessing Maintenance Components ..
  • Page 12 STATEMENT............... 159 BRP INTERNATIONAL LIMITED WARRANTY: 2021 CAN-AM ® SSV..161 BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE INDEPENDENT STATES AND TURKEY: 2021 CAN-AM ®...
  • Page 13: Safety Information

    SAFETY INFORMATION ________ ________ SAFETY INFORMATION...
  • Page 14: General Precautions

    Avoid Gasoline Fires and vehicle. These modifications have not Other Hazards been tested by BRP and they may in- crease the risk of injury or loss of con- Gasoline is extremely flammable and trol, or render the vehicle illegal to ride.
  • Page 15: Operation Warnings

    OPERATION WARNINGS The following list is not exhaustive. WARNING POTENTIAL HAZARD Operating this vehicle without proper instruction. WHAT CAN HAPPEN The risk of an accident is greatly increased if the operator does not know how to operate this vehicle properly in different situations and on different types of terrain.
  • Page 16 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle on paved surfaces. WHAT CAN HAPPEN Paved surfaces may seriously affect handling and control of the vehicle, and may cause the vehicle to go out of control. HOW TO AVOID THE HAZARD If a road usage is allowed in your area, operate your vehicle on paved sur- faces only for short distance and for the only purpose of moving the vehicle from an off-road usage to another.
  • Page 17 OPERATION WARNINGS WARNING POTENTIAL HAZARD Using this vehicle with drugs or alcohol. WHAT CAN HAPPEN Could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. HOW TO AVOID THE HAZARD The operator should never use this vehicle with drugs or alcohol.
  • Page 18 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating. Failure to properly maintain the vehicle. WHAT CAN HAPPEN Increases the possibility of an accident or equipment damage. HOW TO AVOID THE HAZARD Always inspect your vehicle prior to ride to make sure the vehicle is in safe operating condition.
  • Page 19 OPERATION WARNINGS WARNING POTENTIAL HAZARD Failure to use extra care when operating this vehicle on unfamiliar terrain. WHAT CAN HAPPEN You can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. HOW TO AVOID THE HAZARD Go slowly and be extra careful when operating on unfamiliar terrain.
  • Page 20 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating on excessively steep hills. WHAT CAN HAPPEN The vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. HOW TO AVOID THE HAZARD Never operate this vehicle on hills too steep for the vehicle or for your abili- ties.
  • Page 21 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly crossing hills or turning on hills. WHAT CAN HAPPEN Could cause loss of control or cause vehicle to overturn. HOW TO AVOID THE HAZARD Never attempt to turn the vehicle around on any hill until you have mastered the turning technique as described in this Operator's Guide on level ground.
  • Page 22 OPERATION WARNINGS WARNING POTENTIAL HAZARD Improperly operating over obstacles. WHAT CAN HAPPEN Could cause loss of control, or a collision. Could cause the vehicle to overturn. HOW TO AVOID THE HAZARD Before operating in a new area, check for obstacles. Never attempt to ride over large obstacles, such as large rocks or fallen trees.
  • Page 23 OPERATION WARNINGS WARNING POTENTIAL HAZARD Operating this vehicle through deep or fast flowing water. WHAT CAN HAPPEN Tires may float, causing loss of traction and loss of control, which could lead to an accident. HOW TO AVOID THE HAZARD Never operate this vehicle in fast flowing water or in deep water. Check water depth and current before you attempt to cross any water.
  • Page 24 Never modify this vehicle through improper installation or use of acces- sories. All parts and accessories added to this vehicle should be approved by BRP and should be installed and used according to instructions. If you have questions, consult an authorized Can-Am dealer.
  • Page 25 OPERATION WARNINGS WARNING V03M01Q POTENTIAL HAZARD Transporting flammable or dangerous material can lead to explosions. WHAT CAN HAPPEN This can cause serious injury or death. HOW TO AVOID THE HAZARD Never transport flammable or dangerous material. ________ ________ SAFETY INFORMATION...
  • Page 26: Safe Operation - Responsibilities

    We dents. Even with vehicle safety fea- also urge you to visit your authorized BRP dealer in a timely manner if you tures (such as protective structure, seat belts, side nets, doors) and pro- become aware of any safety related tective gear (such as a helmet), there is campaigns.
  • Page 27: Riding Carefully

    SAFE OPERATION - RESPONSIBILITIES Carrying Passengers – Never attempt skidding or sliding. If vehicle starts to skid or slide, Only carry one passenger. The pas- counter steer in the direction of senger must be properly seated in the skidding or sliding. On extremely cockpit.
  • Page 28: European Community

    SAFE OPERATION - RESPONSIBILITIES – Never operate excessively – Always ensure to properly park the rough, slippery or loose terrain un- vehicle on the flattest terrain section til you have learned and practiced available. Put shift lever in PARK, the skills necessary to control this stop engine and remove key before vehicle on such terrain.
  • Page 29: Pre-Ride Inspection

    PRE-RIDE INSPECTION Always inspect and confirm the safe operating condition of your vehicle prior to ride. Always follow the maintenance schedule described in this Operator's Guide. WARNING Perform a pre-ride inspection before each ride to detect any potential prob- lem that could occur during operation. The pre-ride inspection can help you monitor component wear and deterioration before they become a problem.
  • Page 30 PRE-RIDE INSPECTION ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Cargo Load: If you transport a cargo, respect the maximum loading capacity. Refer to LOADING THE CARGO BOX . Ensure cargo is properly secured to the rear cargo box. Vehicle Load: Ensure that total load on the vehicle (including operator, passengers, cargo, tongue weight and added accessories) does not exceed specifications.
  • Page 31 PRE-RIDE INSPECTION ITEMS TO BE ✔ INSPECTION TO PERFORM INSPECTED Press on the accelerator pedal a few times to ensure it Accelerator pedal operates freely and it returns to the rest position when released. Press down on the brake pedal and make sure you feel Brake pedal firm resistance and that it fully returns to position when released.
  • Page 32: Prepare To Ride

    PREPARE TO RIDE Before you Ride Weather conditions should help you decide how to dress. To maximize Perform pre-ride inspection to confirm comfort and avoid frostbites in win- the safe operating condition of your ter, dress for the coldest weather ex- PRE-RIDE INSPEC- vehicle.
  • Page 33 PREPARE TO RIDE Use tinted face shields or goggles in crash, good quality protective gear the daytime only; do not use them at made of sturdy material may prevent night or in poor illumination. Do not or reduce injury. use them if they impair your ability to In cool-weather riding, protect your- discern color.
  • Page 34: Avoid Accidents

    AVOID ACCIDENTS Avoid Rollovers and – Never attempt donuts, skids, slides, fishtails, jumps, or other stunts. If Tipovers vehicle starts to skid or slide, steer Side-by-side vehicles handle differ- in the direction of the skid or slide. ently from other vehicles. Side-by-side Never slam the brakes and lock the vehicles are designed to handle wheels.
  • Page 35: Avoid Collisions

    AVOID ACCIDENTS – Never grab the cage or ROPS while riding. Hands can be crushed be- tween the cage or ROPS and the ground in a rollover. Keep hands on the steering wheel or handholds. – Never try to stop a rollover using your arms or legs.
  • Page 36: Riding Your Vehicle

    RIDING YOUR VEHICLE Practice Exercises U Turn Exercises Practice doing U turns. Before you go out for a ride, it is very important to familiarize yourself with – Accelerate slowly and while remain- the handling of your vehicle by prac- ing at low speed, then gradually turn ticing in a controlled environment.
  • Page 37: Off-Road Operation

    RIDING YOUR VEHICLE Emergency Engine Stopping In off-road operation, power and trac- Exercise tion, not speed, are important. Never drive faster than visibility and your own Learn how to stop your engine quickly ability to select a safe route permit. in an emergency situation.
  • Page 38 RIDING YOUR VEHICLE Riding on Snow or Ice WARNING When performing pre-ride inspection, When driving downhill in reverse, pay special attention to locations on gravity can increase the vehicle the vehicle where snow and/or ice ac- speed above safe reverse speed. cumulations may obstruct visibility of the tail lamp, clog ventilation openings, Crossing Roads...
  • Page 39 RIDING YOUR VEHICLE The depth of the snow cover may hide may cause loose stones to be ejected rocks, tree stumps or other objects and rearwards into the path of another if it is wet may totally impede the driv- rider's way.
  • Page 40 RIDING YOUR VEHICLE Uphill Driving of one side of the vehicle higher than the other, thus causing rollover. If you Use the low range (L) for uphill driving. feel the vehicle start to rollover or slide Due to its configuration, this vehicle sideways, steer downhill if possible.
  • Page 41 RIDING YOUR VEHICLE around you will help you make a better areas. The hazards you may create on choice of appropriate safe distance. the trail may cause injury to others or This vehicle, like any other motorized yourself, even at a later date. vehicle, cannot stop “on a dime”.
  • Page 42: Moving Loads And Doing Work

    MOVING LOADS AND DOING WORK Working with your Vehicle Your vehicle can help you perform a number of different LIGHT tasks ranging from snow removal to pulling wood or carrying cargo. A variety of accessories are avail- able from your authorized Can-Am dealer. To prevent possible injury, follow the in- structions and warnings that accompany the accessory.
  • Page 43: Hauling A Load

    Hauling a Load When pulling another vehicle, be sure that someone is controlling the pulled NOTICE A BRP approved rear vehicle. They must brake and steer to hitch must be properly installed on prevent the vehicle from going out of the vehicle for hauling trailers.
  • Page 44 MOVING LOADS AND DOING WORK may have to be installed on the vehicle hitch). Use security chains or cables to secure the trailer to the vehicle. Reduce your speed when pulling a trailer and turn gradually. Avoid hills and rough terrain. Never attempt steep hills.
  • Page 45: Important On-Product Labels

    IMPORTANT ON-PRODUCT LABELS Hang Tag This vehicle comes with a hang tag and labels containing important safety informa- tion. Any person who rides this vehicle should read and understand this information be- fore riding. Vous pouvez aussi vous procurer des Digitally Encoded Security System clés D.E.S.S.
  • Page 46 IMPORTANT ON-PRODUCT LABELS 8097 EN-704908097-DEC TYPICAL - DO NOT LEAVE KEY IN ACC POSITION _______ ________ SAFETY INFORMATION...
  • Page 47: Safety Labels

    IMPORTANT ON-PRODUCT LABELS Safety Labels Read and understand all the safety labels on your vehicle. These labels are affixed to the vehicle for the safety of the operator, passengers or bystanders. The following labels are on your vehicle, and they should be considered perma- nent parts of the vehicle.
  • Page 48 IMPORTANT ON-PRODUCT LABELS 219002044-010 TYPICAL 219002040-005 219002044-011 TYPICAL TYPICAL 219002044-013 TYPICAL _______ ________ SAFETY INFORMATION...
  • Page 49 Do not put any part of your body outside of t he vehicle for any reason. – Always stay completely inside the vehic le. – Do not let people drive or ride after usi ng alcohol or drugs. https://can-am.brp.com/off-road/safety 7646 Patent : www.brp.com/en/about-brp/patents.html EN-704907646-DEC LABEL 1 ________ ________...
  • Page 50 IMPORTANT ON-PRODUCT LABELS Label 2 WARNING – Always wear an approved helmet and protective gear. – Always wear ear protection. – Fasten seat belts and nets. – Each rider must be able to sit with back against seat, feet flat on the floor or on footrest, and hands on handholds.
  • Page 51 IMPORTANT ON-PRODUCT LABELS Label 4 WARNING – Put the Shift Lever to PARK (P) before exiting vehicle. The vehicle can roll if not in PARK. – Stop the vehicle and apply the Brake before using the Shift Lever and the 2WD/4WD Switch.
  • Page 52 IMPORTANT ON-PRODUCT LABELS Label 5 WARNING – Locate and read operator's guide. Improper tire pressure or overloading can cause loss of control, resulting in SEVERE INJURY or DEATH. – Always maintain proper tire pressure as shown. – NEVER exceed the vehicle load capacity of 331 kg (730 lb), including weight of operator, passenger, cargo, accessories and trailer tongue weight if applicable.
  • Page 53 IMPORTANT ON-PRODUCT LABELS Label 6 WARNING – Refer to operator's guide for more details. – NEVER place gasoline, flammable or dangerous liquids container on car- rier. This can lead to an explosion. – NEVER carry passenger in cargo box or tailgate. –...
  • Page 54 IMPORTANT ON-PRODUCT LABELS Label 9 WARNING – Never try to stop a rollover us- ing your arm or leg. – Never hold the cage while rid- ing. – Fasten net or door and seat belt to help you avoid sticking out arms or legs.
  • Page 55 IMPORTANT ON-PRODUCT LABELS Label 10 WARNING – NEVER attach to the cage to pull a load. This can cause the vehicle to tip over. Use only the trailer hitch or recovery hook to pull a load. EN-704907694-DEC LABEL 10 L L abel 11 L L abel 12 WARNING Запуск...
  • Page 56: Technical Information Labels

    IMPORTANT ON-PRODUCT LABELS Technical Information Labels – Refer to the operator's guide for maintenance procedure. EN-704908620-DEC ON FRONT AND REAR SUSPENSION ARMS 7686 EN-704907686-DEC ON AIR FILTER BOX 704906395-DEC ON BRAKE FLUID RESERVOIR 7695 EN-704907695-DEC LOCATION: ON ENGINE AIR FILTER HOUSING COVER - 1000R ONLY 704906322-DEC ON SHIFT LEVER GRILL (PARK POSITION)
  • Page 57: Compliance Labels

    IMPORTANT ON-PRODUCT LABELS Compliance Labels These labels indicate vehicle's compli- ance. 219002040-012 TYPICAL 000198U5S EN-704908232-DEC TYPICAL - LH TOP OF CAGE 704906393 EN-704906393-DEC LH TOP OF CAGE 704907278-DEC LOCATED NEAR GAS CAP ________ ________ SAFETY INFORMATION...
  • Page 58 IMPORTANT ON-PRODUCT LABELS This page is intentionally blank _______ ________ SAFETY INFORMATION...
  • Page 59: Vehicle Information

    VEHICLE INFORMATION _______________...
  • Page 60: Primary Controls

    PRIMARY CONTROLS It is important to know the location and operation of all controls, and to develop and practice smooth and coordinated use of them. NOTE: Some vehicle safety labels are not shown on illustrations. For information IMPORTANT ON-PRODUCT LABELS on vehicle safety labels, refer to 219002128-012 TYPICAL - PRIMARY CONTROLS...
  • Page 61: Accelerator Pedal

    PRIMARY CONTROLS CAUTION Under rough trail conditions or when crossing an ob- stacle, the steering wheel could sud- denly jerk on one side, causing hand or wrist injuries if the thumbs are rolled around the steering wheel. The DPS (Dynamic Power Steering) reduces the effort to turn the steering wheel.
  • Page 62 PRIMARY CONTROLS WARNING This gearbox is not designed to shift while vehicle is moving. Park The park position locks the gearbox to help prevent vehicle movement. WARNING Always use the PARK (P) position when the vehicle is not in oper- ation.
  • Page 63: Secondary Controls

    SECONDARY CONTROLS NOTE: Some vehicle safety labels are not shown on illustrations. For information IMPORTANT ON-PRODUCT LABELS on vehicle safety labels, refer to 219002128-001 TYPICAL - SECONDARY CONTROLS 1) RF D.E.S.S Key and RF RF D.E.S.S. Key D.E.S.S. Post For all D.E.S.S. related option, see an authorized Can-Am dealer for informa- RF D.E.S.S.
  • Page 64: Engine Start/Stop Button

    SECONDARY CONTROLS Refer to your dealer for complete infor- desirable. For example, in narrow, mation. winding trails, operators may prefer a normal key. NOTE: Additional keys are available from your dealer as an accessory. D.E.S.S. Flexibility The D.E.S.S. of your vehicle can be pro- WARNING grammed by your authorized Can-Am Rollovers, tipovers, collisions and...
  • Page 65: Multifunction Lever

    SECONDARY CONTROLS 3) Multifunction Lever 4) Hazard Warning Switch The hazard warning switch is located Low/High Beam Selection on the upper console. 219002128-004 219002128-005 1. Multifunction lever 1. Hazard warning switch When the multifunction lever is in the This switch operates all the turn signals middle position, the low beam is se- simultaneously.
  • Page 66: 2Wd/4Wd Switch

    SECONDARY CONTROLS 7) Rear Differential Lock Switch (ABS models only) The Differential lock switch is located on the console. 219002128-006 KEYPAD The keypad is used to navigate through various menus and options. Refer to 7.6" DIGITAL DISPLAY 219002128-008 6) 2WD/4WD Switch 1.
  • Page 67 SECONDARY CONTROLS Hill Descent Control (HDC) function should be used to allow a smooth and controlled hill descent when driving down a steep incline without the driver having to press the brake pedal. The vehicle should maintain set speed without any intervention from the driver.
  • Page 68: Digital Display

    7.6" DIGITAL DISPLAY Basic Functions Left Lateral Display Multifunction Gauge Description WARNING Do not adjust the display while rid- ing, you could lose control. General View 219002042-302 The left lateral display includes: – Fuel level indicator – Tripmeter (A - B) –...
  • Page 69 7.6" DIGITAL DISPLAY May display the following: The ECO (fuel economy mode) setting reduces fuel consumption by limit- – RPM ing throttle response and maximum – Vehicle speed throttle opening to maintain an optimal cruising setting. Transmission Position Display NOTE: Use ECO mode on bumpy trails to provide smoother ride con- ditions.
  • Page 70 7.6" DIGITAL DISPLAY WARNING AND TELLTALE LIGHTS ORANGE - ABS* 4X4 ICON FOR ALL OTHER COUNTRIES RED - (Steady ON) Low Brake Fluid Middle Left Display The middle left lateral display includes: RED - (Blinking) Accelerator pedal and the brake are –...
  • Page 71: Settings

    7.6" DIGITAL DISPLAY Settings ICONS AND INDICATORS When lit, seat belt Setup not buckled with Using MENU button on the keypad, se- vehicle immobilized. lect SETTINGS and hold to enter set- Flashing when vehicle ting menu. is moving. OK button can be pressed instead of When lit, indicates holding MENU button.
  • Page 72 7.6" DIGITAL DISPLAY Unit Selection Using MENU button, adjust brightness then push and hold MENU button to ac- This multifunction gauge is factory pre- knowledge selection. set in Imperial units but it is possible to change it to Metric units. Setting Language Using MENU button, select UNITS The gauge display language can be...
  • Page 73 7.6" DIGITAL DISPLAY Activating Speed Limiter Mode NOTE: Activating speed limiter mode of operation only limits the maximum 1. Press the keypad MENU button to speed available when depressing the SETTINGS go to the menu. throttle. The throttle must be held in to SPEED LIM 2.
  • Page 74: Driving Aid Technologies

    DRIVING AID TECHNOLOGIES These systems actively manage brak- The driver can change the set speed ing and traction. by pressing the accelerator or brake pedal. Under certain conditions, the driver may feel the actions taken by the sys- HDC can be activated and deactivated tems in the form of vibrations or slight by pressing the HDC button.
  • Page 75: Equipment

    EQUIPMENT NOTE: Some vehicle safety labels are not shown on illustrations. For information IMPORTANT ON-PRODUCT LABELS on vehicle safety labels, refer to 219002128-010 TYPICAL _______________...
  • Page 76 EQUIPMENT 219002007-004_a TYPICAL 219002044-009 TYPICAL ______________...
  • Page 77: Tilt Steering

    EQUIPMENT 1) Tilt Steering The steering wheel height is ad- justable. Adjust the steering wheel height to face your chest, not your head. To adjust steering wheel height: 1. Unlock steering by pulling the tilt lever toward you. 2. Move steering wheel to the desired 219001880-009_a position.
  • Page 78: Storage Compartments

    EQUIPMENT 4) Storage Compartments WARNING The vehicle is equipped with storage When riding vehicle, make sure no compartments designed to carry light object stored in open storage com- objects. partments could cause harm in the event of a roll over. Storage Compartment (Driver side) A storage compartment is available be- hind the multifunction gauge.
  • Page 79: Side Nets

    EQUIPMENT 7) Side Nets 8) Shoulder Guards A side net is provided on each side of The vehicle is equipped with shoulder the cockpit to help arms, legs or shoul- guards to help restrain the entire body ders stay inside the vehicle, thus re- of driver and passenger inside vehicle.
  • Page 80: Driver's Seat

    EQUIPMENT 219001880-014_a 1. Adjustment lever tmr2014-037-005_a 1. Semi-cinching tab To adjust seat, move the seat lever to unlock the seat. Release the lever to To fasten the seat belt, insert the latch lock the seat into desired position. plate into the buckle, then pull the belt The driver seat is equipped with a sen- to ensure it is properly fastened.
  • Page 81: Cargo Box

    EQUIPMENT 219001880-015_a 219001880-016_c TYPICAL TYPICAL 1. Fuel reservoir cap 1. Anchoring Hooks FUEL Refer to for information on fuel- There are 6 anchoring points inside the ing procedure and fuel requirements. cargo box to install LinQ attachments and 2 on top of the sides. 13) Cargo Box The cargo box may be used for various types of cargo.
  • Page 82: Hitch Draw Bar

    EQUIPMENT Hitch Draw Bar Installation Insert the draw bar in the receiver hitch. 219002007-006_a 1. Receiver For the proper usage of the hitch sup- MOVING LOADS AND port, refer to DOING WORK 219002007-008_a Insert the pin through the draw bar and WARNING receiver hitch.
  • Page 83: Trailer Lights Connector

    EQUIPMENT 17) Trailer Lights Connector Connector to be used if the trailer is equipped with lights. For towing, refer to towing instructions label located at trailer hitch. 219002007-012_a WARNING Do not adjust mirrors while riding. You could lose control. 20) 12-Volt Power Outlets Convenient for handheld spotlight or 219002044-012 other portable equipment.
  • Page 84: Full Underbody Skid Plate

    EQUIPMENT 21) Full Underbody Skid Plate Skid plates provide essential protec- tion. 219002042-010 TYPICAL ______________...
  • Page 85: Tune Your Ride

    TUNE YOUR RIDE Suspension Adjustment REAR SUSPENSION FACTORY SETTINGS Guidelines Your vehicle handling and comfort de- FACTORY ADJUSTMENT pend upon suspension adjustments. SETTING Maverick Cam position WARNING Trail 1 (soft) Spring Suspension adjustment could af- preload Maverick fect vehicle handling. Always take 87.8 mm Sport time to familiarize yourself with...
  • Page 86 TUNE YOUR RIDE Maverick Sport Models WARNING The left and right shock adjust- ment on front or rear suspension must always be set to the same position. Never adjust one shock only. Uneven adjustment can cause poor handling and loss of stability, which could lead to an ac- cident.
  • Page 87: Fuel

    FUEL Fuel Requirements NOTICE Always use fresh gaso- line. Gasoline will oxidize; the re- sult is loss of octane, volatile com- pounds, and the production of gum NOTICE Never experiment with and varnish deposits which can other fuels. Engine or fuel system damage the fuel system.
  • Page 88 FUEL 219001880-015_a TYPICAL 1. Fuel reservoir cap WARNING If a differential pressure condition is noticed (whistling sound heard when loosening fuel reservoir cap) have vehicle inspected and/or re- paired before further operation. 4. Insert the spout into the filler neck. 5.
  • Page 89: Break-In Period

    BREAK-IN PERIOD Operation During Break-In A break-in period of 10 operating hours or 300 km (200 mi) is required for the vehicle. Engine During the break-in period: – Avoid full throttle operation. – Avoid pressing accelerator pedal more than 3/4 of the stroke. –...
  • Page 90: Basic Procedures

    BASIC PROCEDURES Starting the Engine Release brakes. Install D.E.S.S. key on D.E.S.S. post. NOTICE When changing gear se- Press the brake pedal. lection, always completely stop the vehicle and apply the brakes prior NOTE: If shift lever is not set to PARK to shifting.
  • Page 91: Stopping The Engine And Parking The Vehicle

    BASIC PROCEDURES This function is activated when riding WARNING at too slow speed for the high range, Always put the vehicle in PARK such as in the following situations: when stopped or parked to pre- – Pulling vent rolling. – Pushing –...
  • Page 92 BASIC PROCEDURES If riding in any of the conditions listed below, BRP highly recommends not to constantly hold the throttle wide open (WOT) for more than five (5) minutes. – High ambient temperatures (above 30°C (86°F) – Heavy loads: Passengers / Heavy cargo –...
  • Page 93: Special Procedures

    SPECIAL PROCEDURES What to do if Water is Should the vehicle be rolled over, it will be necessary to have it transported Suspected to be in the CVT to an authorized Can-Am dealer for in- If water is present in the CVT, the en- spection as soon as possible.
  • Page 94: Transporting The Vehicle

    TRANSPORTING THE VEHICLE When contacting a towing or trans- SAFETY PRECAUTIONS porting service, be sure to ask if they Ensure you have a good have a flatbed trailer, loading ramp or Visibility visibility during the entire power ramp to safely lift the vehicle maneuver.
  • Page 95: Using A Winch To Pull Vehicle Onto Trailering Equipment

    TRANSPORTING THE VEHICLE 3. Back off the vehicle, verify ramps 2. If the vehicle is equipped with a are still secure, then proceed at winch, use the winch to roll the ve- proper speed. hicle on the platform. 4. Carefully drive vehicle onto platform 3.
  • Page 96: Getting Vehicle Out Of Trailer

    TRANSPORTING THE VEHICLE 5. Firmly attach the rear suspension tie-down straps to both sides of the rear of the trailer with ratchets. 6. Ensure that both the front and rear wheels are firmly attached to the trailer. Getting vehicle out of trailer WARNING Vehicle may have moved during...
  • Page 97: Lifting And Supporting The Vehicle

    LIFTING AND SUPPORTING THE VEHICLE Front of Vehicle Rear of Vehicle Place vehicle on a flat non slippery Place vehicle on a flat non slippery ground. ground. Ensure vehicle shift lever is set to Activate 4WD mode. PARK. Ensure vehicle shift lever is set to Install an hydraulic jack under front skid PARK.
  • Page 98 LIFTING AND SUPPORTING THE VEHICLE This page is intentionally blank ______________...
  • Page 99: Maintenance

    MAINTENANCE _______________...
  • Page 100: Maintenance Schedule

    For emission-related warranty claims, BRP is limiting the diagnosis and repair of emission-related parts to the authorized Can-Am Off-Road dealers. For more US EPA EMISSION-RELATED WARRANTY...
  • Page 101: Maintenance Schedule Legend

    MAINTENANCE SCHEDULE NOTE: Riding in a group in these conditions would increase even more the air filter maintenance. MAINTENANCE SCHEDULE LEGEND Operation in trail riding conditions Operation in severe riding conditions (dusty or muddy) or carrying heavy loads condition MAINTENANCE SCHEDULE Make sure to perform proper maintenance at recommended intervals as indicated in the tables.
  • Page 102 MAINTENANCE SCHEDULE EVERY YEAR OR EVERY 3 000 KM (2,000 MI) OR 100 HOURS (whichever comes first) EVERY YEAR OR EVERY 1 500 KM (1,000 MI) OR 50 HOURS (whichever comes first) Inspect battery condition and connections Inspect propeller shaft U-joints for abnormal play. Clean exhaust pipes and muffler area Clean muffler spark arrester Adjust valve clearance...
  • Page 103 MAINTENANCE SCHEDULE EVERY 5 YEARS OR EVERY 12 000 KM (8,000 MI) (whichever comes first) EVERY 5 YEARS OR EVERY 6 000 KM (4,000 MI) (whichever comes first) Replace engine coolant ______________...
  • Page 104: Maintenance Procedures

    Can-Am off-road dealer, re- pair shop or person of your own choos- ing. 219002007-200_a WARNING 2. Align the BRP logo with the locating dowel. Unless otherwise indicated, al- ways turn ignition switch to the OFF position before performing any maintenance and remove key.
  • Page 105 MAINTENANCE PROCEDURES Remove the seat cushion by lifting the front up and pulling toward the front, remove the backrest by pulling the lower part toward the front and lifting 219001880-058_a 219001880-029_a SEAT CUSHION Step 1: lift front of seat Step 2: Pull toward the front 219001880-064_a RH SIDE SHOWN, REPEAT ON LH SIDE 219001880-029_b...
  • Page 106: Engine Air Filter

    MAINTENANCE PROCEDURES 219001880-025_a 219001880-060_a 1. Quarter turn fasteners 1. Cage extension upper screw 2. Cage extension lower screw 3. Electrical connector 5. Lift rear body module. 219001880-059_a 1. Plastic rivet 2. Side panel 3. On LH side, remove side panel. 219001880-065 Engine Air Filter NOTICE...
  • Page 107 MAINTENANCE PROCEDURES – Riding on dry gravel trails or similar The filter fits tightly over the outlet conditions. tube and there will be some initial re- sistance. Gently move the end of the – Riding in areas with high concentra- filter back and forth to break the seal, tion of seeds or crop husks.
  • Page 108: Cvt Air Filter

    MAINTENANCE PROCEDURES Secure air filter cover with latches. 219001880-027_a CVT Air Filter Inspection and 219001880-026_a Cleaning RH SIDE OF VEHICLE, UNDER CARGO BOX 1. Inspect filter and replace if dam- 1. Air filter cover aged. 2. Latches 3. Duck bill valve 2.
  • Page 109: Engine Oil

    Rotax ® engines were developed and 219001880-028_a validated using the XPS™ oil. BRP rec- 1. Engine oil dipstick ommends the use of its XPS engine oil or an equivalent at all time. Damages 3. Reinstall dipstick, screw in it com- pletely.
  • Page 110 MAINTENANCE PROCEDURES Clean the drain plug area. XPS RECOMMENDED ENGINE OIL Unscrew drain plug and discard the Scandinavia: gasket ring. 4T 5W40 SYNTHETIC BLEND OIL (EUR) (P/N 779290) General purpose Other Countries: 4T 5W40 SYNTHETIC BLEND OIL (P/N 779133) Scandinavia: 4T 0W40 SYNTHETIC OIL (EUR) (P/N 779286) Cold...
  • Page 111: Oil Filter

    MAINTENANCE PROCEDURES Oil Filter Oil Filter Access Remove passenger seats, refer to CESSING MAINTENANCE COMPO- NENTS Remove the engine service cover. tmr2011-010-004_a TYPICAL 1. Oil filter screw 2. Oil filter cover 3. O-ring 4. Oil filter Oil Filter Installation Check and clean the oil filter inlet and outlet area for dirt and other contami- nations.
  • Page 112: Radiator

    MAINTENANCE PROCEDURES Inspect radiator and hoses for leaks or any damage. Inspect radiating fins. They must be clean, free of mud, dirt, leaves and any other deposit that would prevent the radiator to cool properly. If available, use a garden hose to rinse the radiating fins.
  • Page 113 MAINTENANCE PROCEDURES Recommended Engine Coolant WARNING In order to avoid potential burns, RECOMMENDED COUNTRY do not remove the pressure cap if COOLANT the engine is hot. EXTENDED LIFE PRE-MIXED Scandinavia 3. Ensure cooling system is full up to COOLANT (EUR) the Max line.
  • Page 114 MAINTENANCE PROCEDURES 2. Remove the cooling system pres- sure cap. 219001880-035_a TYPICAL 1. Lower radiator hose to disconnect 5. Drain cooling system completely. 219001880-034_a 1. Pressure cap 6. Reinstall cooling system drain plug and tighten to specification. 3. Unscrew coolant drain plug and drain the coolant into a suitable con- TIGHTENING TORQUE tainer.
  • Page 115: Muffler And Spark Arrester

    MAINTENANCE PROCEDURES 3. Install pressure cap. 4. Run engine at idle with the pressure cap ON until the cooling fan cycles on for a second time. 5. Stop the engine and let it cool down. WARNING In order to avoid potential burns, do not remove the pressure cap if 219002008-003 the engine is hot.
  • Page 116: Gearbox Oil

    (P/N 779160) NOTE: The XPS oil is specially formu- lated to meet the lubrication require- ments of this gearbox. BRP strongly recommends the use of its XPS oil. However, if the XPS synthetic gear oil is not available, use the following lubri-...
  • Page 117: Differential Oil

    MAINTENANCE PROCEDURES Remove the oil level plug. Lubricate O-ring and reinstall VSS. Remove the gearbox drain plug. SERVICE PRODUCT SUPER LUBE VSS O-Ring GREASE (P/N 293 550 030) TIGHTENING TORQUE Gearbox drain 30 N•m ± 3 N•m plug (22 lbf•ft ± 2 lbf•ft) 10 N•m ±...
  • Page 118 TYPICAL - FRONT RIGHT SIDE OF VEHICLE NOTE: The XPS oil is specially formu- lated to meet the lubrication require- Install drain plug. ments of this gearbox. BRP strongly recommends the use of its XPS oil. TIGHTENING TORQUE However, if the XPS synthetic gear oil 2.7 N•m ±...
  • Page 119: Spark Plugs

    MAINTENANCE PROCEDURES Spark Plugs Spark Plug Removal Unplug spark plug cable. Access to Spark Plugs ACCESSING MAINTENANCE Refer to COMPONENTS and remove the seats. Remove the engine service cover. 219001880-041_a TYPICAL 1. Spark plug 219001880-030_a 219001880-042_a 1. Spark plug 219001880-057_a Clean spark plug area with pressurized 1.
  • Page 120: Cvt Cover

    MAINTENANCE PROCEDURES Screw spark plug into cylinder heads by hand and tighten with a torque wrench and a proper socket. NOTICE Do not overtighten spark plugs, engine damage can occur. TIGHTENING TORQUE Spark plug (800 20 N•m ± 2.4 N•m (15 lbf•ft ±...
  • Page 121: Drive Belt

    MAINTENANCE PROCEDURES tmo2016-010-093_a TYPICAL 1. Fixed sheave of driven pulley tmo2016-010-036_a 2. Adaptor 3. Puller/locking tool TIGHTENING TORQUE 4. Wrench 7 N•m ± 0.8 N•m CVT cover To remove belt, slip the belt over the screws (62 lbf•in ± 7 lbf•in) top edge of fixed sheave, as shown.
  • Page 122: Drive And Driven Pulleys

    MAINTENANCE PROCEDURES Driven Pulley Inspect the bushings of the cam and of the sliding sheave of the driven pulley, replace worn parts. Battery Battery Maintenance NOTICE Never charge a battery vmr2007-051-006_a while installed in vehicle. 1. Arrow printed on belt 2.
  • Page 123: Fuses And Fusible Links

    MAINTENANCE PROCEDURES Battery Cleaning Clean battery, battery casing and bat- tery posts using a solution of baking soda and water. Remove corrosion from battery cable terminals and battery posts using a firm wire brush. Battery casing should be cleaned by soft brush and baking soda solution.
  • Page 124: Lights

    MAINTENANCE PROCEDURES SINGLE FUSES AT FRONT REAR FUSE BOX DESCRIPTION RATING DESCRIPTION RATING 40 A Cluster/relays 10 A Accessory post Ignition/injection/fuel 10 A (Under dash 40 A pump terminal block) Engine Control 10 A ABS Pump 40 A Module (ECM) ABS Valves 25 A 4WD actuator...
  • Page 125 MAINTENANCE PROCEDURES Taillight Bulbs Replacement The taillights are built with LEDs (light emitting diode) and this technology proved to be reliable. In the unlikely event they do not work, have them checked or replaced by an authorized Can-Am dealer, a repair shop or person of your choosing.
  • Page 126: Drive Shaft Boot And Protector

    MAINTENANCE PROCEDURES 2. Remove the light bulb socket. 3. Reinstall the cover. 3. Replace the light bulb. Drive Shaft Boot and 4. Reinstall the bulb socket and other Protector removed parts in the reverse order. Drive Shaft Boot and Protector Front Position Light Replacement Inspection NOTE: The front position lights cannot...
  • Page 127: Wheel Bearing

    MAINTENANCE PROCEDURES 219001880-051_a tmo2016-010-047_a TYPICAL - REAR OF VEHICLE TYPICAL 1. Inner drive shaft boots Wheels and Tires Wheel Removal Loosen wheel lug nuts. Then lift and LIFTING support vehicle. Refer to AND SUPPORTING VEHICLE Remove wheel. Wheel Installation Inspect studs and nuts. Replace if needed.
  • Page 128: Suspensions

    MAINTENANCE PROCEDURES NOTICE Always use the recom- WARNING mended wheel nuts for the type of – Replace tires only with the same wheel. Using a different nut could type and size as original tires. cause damages to the rim or studs. –...
  • Page 129 MAINTENANCE PROCEDURES Suspension Inspection See an authorized Can-Am dealer, a re- pair shop or person of your choosing if any problem is detected. Shock Absorbers Inspect shock absorber for leaks, bump stop wear out or other damages. Verify if fasteners are still well tight- ened.
  • Page 130: Brakes

    MAINTENANCE PROCEDURES TIGHTENING TORQUE 112 N•m ± 7.5 N•m M12 bolt (83 lbf•ft ± 6 lbf•ft) NOTE: The suspension arms must be tightened on the M12 bolt head and not on the nut (when possible) to insure op- timal clamping. 219002126-019 1.
  • Page 131: Seat Belts

    MAINTENANCE PROCEDURES WARNING The brake fluid replacement or brake system maintenance and repairs should be performed by an authorized Can-Am dealer. Seat Belts Seat Belt Cleaning 219002007-017_a To clean dirt and debris from the seat 1. Brake fluid reservoirs belts, sponge the straps with mild soap 2.
  • Page 132 MAINTENANCE PROCEDURES 219002007-019_a ACCESSING MAINTENANCE Refer to COMPONENTS and remove the seats backrest. Tighten all fasteners. 219001880-114_a 219001880-115_a ACCESSING MAINTENANCE Refer to COMPONENTS for the cage extension procedure. TIGHTENING TORQUE 80 N•m ± 10 N•m Cage fasteners (59 lbf•ft ± 7 lbf•ft) ______________...
  • Page 133: Vehicle Care

    VEHICLE CARE Post-Operation Care When required, wash the body with warm water and soap (only use mild When vehicle is used in salt-water detergent). Apply non-abrasive wax. environment rinsing the vehicle with fresh water is necessary to preserve NOTICE Never clean plastic parts vehicle and its components.
  • Page 134: Storage And Preseason Preparation

    STORAGE AND PRESEASON PREPARATION When a vehicle is not in use for more than 4 months, proper storage is a ne- cessity. If the vehicle is to be dormant for more than 21 days, disconnect the BLACK (-) cable of the battery. Using electrical accessories increases the risk of discharging the battery.
  • Page 135: Technical Information

    TECHNICAL INFORMATION ______________...
  • Page 136: Ec-Declaration Of Conformity

    EC-DECLARATION OF CONFORMITY DOC_SSV_MY21-EN 16990 ______________...
  • Page 137: Eac Declaration Of Conformity

    EAC DECLARATION OF CONFORMITY Left blank for Eurasian Conformity mark where applicable ______________...
  • Page 138: Specifications

    (48.82 in³) Spark arrester approved Exhaust system by USDA Forest Service Catalyst on NRMM models Engine air filter Synthetic paper filter 1000 MODEL 1000R LUBRICATION SYSTEM Type Wet sump. Replaceable oil filter BRP Rotax paper type, replaceable Oil filter ® ______________...
  • Page 139 SPECIFICATIONS 1000 MODEL 1000R LUBRICATION SYSTEM Type Wet sump. Replaceable oil filter Capacity (oil change 2 L (2.1 qt (U.S. liq.)) with filter) 4T 10W50 SYNTHETIC OIL (EUR) Recommended (P/N 779240) 4T 5W40 SYNTHETIC . or BLEND OIL (EUR) (P/N 779290) Scandinavia 4T 0W40 SYNTHETIC OIL (EUR) (P/N 779286)
  • Page 140 SPECIFICATIONS MODEL 1000 1000R GEARBOX Dual range (HI-LO) with PARK, neutral Type and reverse Capacity 1.5 L (.396 U.S. gal.) 75W140 SYNTHETIC Scandinavia: GEAR OIL (EUR) (P/N 779215) Gearbox oil Recommended 75W140 All other countries: SYNTHETIC GEAR OIL (P/N 779160) or a 75W 140 API GL-5 1000 MODEL...
  • Page 141 SPECIFICATIONS MODEL 1000 1000R FUEL SYSTEM ECO mode: 1350 ± 1250 ± 100 RPM (not 100 RPM Idle speed adjustable) Sport mode: 1500 ± 100 Premium Type Regular unleaded gasoline unleaded gasoline FUEL Fuel - Refer to REQUIREMENTS 91 Pump Minimum 87 Pump Posted AKI (92 RON) Posted AKI...
  • Page 142 SPECIFICATIONS MODEL 1000 1000R STEERING Steering wheel Adjustable tilt steering MODEL 1000 1000R FRONT SUSPENSION Double A- arm suspension with stabilizer bar Suspension type Maverick Trail 5 positions cam Preload adjustment type Maverick Sport Threaded Maverick Trail 254 mm (10 in) Suspension travel 292 mm Maverick Sport...
  • Page 143 SPECIFICATIONS MODEL 1000 1000R BRAKES Dual 220 mm ventilated disc brakes with Front brake Type hydraulic twin-piston calipers Dual 220 mm ventilated disc brake with Rear brake Type hydraulic twin-piston calipers Capacity Approximately 295 ml (10 U.S. oz) Brake fluid Type DOT 4 Floating...
  • Page 144 SPECIFICATIONS MODEL 1000 1000R WHEELS Type Aluminium 35.6 x 17.78 Rim size 30.5 x 15.24 cm (12 x 6 in) cm (14 x 7 in) Wheel lug nuts torque 100 N•m ± 10 N•m (74 lbf•ft ± 7 lbf•ft) Front 41.2 mm (1.6 in) Wheel offset Rear...
  • Page 145 SPECIFICATIONS MODEL 1000 1000R LOADING CAPACITY AND WEIGHT 637.3 kg Maverick Sport (1,405 lb) Maverick Trail 596 kg Dry weight 800 T (1,314 lb) All other 603.7 kg 618.7 kg models (1,330.9 lb) (1,364 lb) Weight distribution (front/rear) 42/58 136 kg (300 lb) Cargo box capacity Total vehicle load allowed (including driver, passengers, all other loads and...
  • Page 146 SPECIFICATIONS This page is intentionally blank ______________...
  • Page 147: Troubleshooting

    TROUBLESHOOTING ______________...
  • Page 148: Troubleshooting Guidelines

    TROUBLESHOOTING GUIDELINES CVT BELT IS SLIPPING 1. Water has entered in the CVT. – Refer to SPECIAL PROCEDURES. "--" IS DISPLAYED ON GEARBOX POSITION DISPLAY (MULTIFUNCTION GAUGE) 1. Shift lever is between 2 positions. – Properly position the shift lever in the desired position. 2.
  • Page 149 TROUBLESHOOTING GUIDELINES ENGINE TURNS OVER BUT FAILS TO START 1. Flooded engine (spark plug wet when removed). – (If the engine does not start and it is fuel-flooded, the drowned mode can be activated to prevent fuel injection and to cut ignition while cranking. Proceed as follows: •...
  • Page 150 TROUBLESHOOTING GUIDELINES ENGINE LACKS ACCELERATION OR POWER (cont’d) 4. Water in CVT – Drain water from CVT. Refer to SPECIAL PROCEDURES. 5. CVT dirty or worn-out. – Contact an authorized Can-Am dealer. 6. Lack of fuel – Dirty or clogged fuel pump pre-filter. Seek service from an authorized Can-Am dealer, repair shop, or person of your own choosing for mainte- nance, repair, or replacement.
  • Page 151 TROUBLESHOOTING GUIDELINES REDUCED POWER STEERING ASSIST 1. When DPS is subjected to sustained severe steering conditions, the assis- tance provided by the DPS motor may be reduced to protect the system. – Once the load is reduced, the normal steering assistance will return. 2.
  • Page 152: Messages In Multifunction Gauge

    MESSAGES IN MULTIFUNCTION GAUGE If an abnormal engine condition occurs, the following messages can be combined with a pilot lamp. MESSAGE DESCRIPTION D.E.S.S. KEY NOT D.E.S.S. key requires cleaning. RECOGNIZED Indicates that you have used the wrong D.E.S.S. key, use the BAD KEY proper key for this vehicle.
  • Page 153: Warranty

    WARRANTY ______________...
  • Page 154: Brp Limited Warranty Usa And Canada: 2021 Can-Am Ssv

    BRP. BRP reserves the right to modify this limited warranty at any time, be- ing understood that such modification will not alter the warranty conditions appli- cable to the products sold while this warranty is in effect.
  • Page 155 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 156 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured.
  • Page 157 If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide. * In the USA, products are distributed and serviced by BRP US Inc.
  • Page 158: Epa Emission-Related Warranty

    2. It is free from defects in materials and workmanship that may keep it from meeting the requirements of 40 CFR 1051 and 40 CFR 1060. Where a warrantable condition exists, BRP will repair or replace, as it elects, any part or component with a defect in materials or workmanship that would increase the engine’s emissions of any regulated pollutant within the stated warranty...
  • Page 159 Components Covered The emission-related warranty covers all components whose failure would in- crease an engine’s emissions of any regulated pollutant, including the following listed components: 1. For exhaust emissions, emission-related components include any engine parts related to the following systems: –...
  • Page 160 If you have any question regarding your warranty rights and responsibility, you should contact Bombardier Recreational Products at 1-888-272-9222. ** In the USA, products are distributed and serviced by BRP US Inc. ______________...
  • Page 161: California Evaporative Emissions Control Warranty

    State’s stringent anti-smog standards. Bombardier Recreational Products Inc. (“BRP”)** must warrant the evaporative emissions control system on your Off-Road Sport Vehicle for the periods of time listed below provided there has been no abuse, neglect, improper maintenance, or unapproved modification of your Off-Road Sport Vehicle.
  • Page 162 Bombardier Recreational Products Inc. at 1-888-272-9222 or the California Air Resources Board at 9528 Telstar Avenue, El Monte, CA 91731. *As related to the evaporative emission control system ** In the USA, products are distributed and serviced by BRP US Inc. ______________...
  • Page 163: Brp International Limited Warranty: 2021 Can-Am Ssv

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 164 – Damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by BRP or resulting from repairs done by a person that is not an authorized servicing Can-Am SSV Distributor/Dealer;...
  • Page 165 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 166 BRP reserves the right to improve or modify products from time to time without as- suming any obligation to modify products previously manufactured. 8) TRANSFER If the ownership of a product is transferred during the warranty coverage period, this limited warranty, subject to its terms and conditions, shall also be transferred...
  • Page 167: Brp Limited Warranty For The European Economic Area, The Commonwealth Of The Independent States And Turkey: 2021 Can-Am Ssv

    BRP. BRP reserves the right to modify this warranty at any time, being understood that such modification will not alter the warranty conditions applicable to the products sold while this warranty is in effect.
  • Page 168 Operator's Guide; – Damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by BRP or resulting from repairs done by a person that is not an authorized servicing Can-Am SSV Distributor/Dealer;...
  • Page 169 BRP will not honor this limited warranty to any private use owner or commercial use owner if one of the preceding conditions has not been met. Such limitations are necessary in order to allow BRP to preserve both the safety of its products, and also that of its consumers and the general public.
  • Page 170 Can-Am SSV Distributor/Dealer's service manager or owner. If the matter still remains unresolved, contact BRP by filling out the customer con- tact form at www.brp.com or contact BRP by mail at one of the addresses listed CONTACT US under the section of this guide.
  • Page 171 ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY The following terms and conditions are applicable to products sold in France only: The seller shall deliver goods that are complying with the contract and shall be responsible for defects existing upon delivery. The seller shall also be responsible for defects resulting from packaging, assembling instructions or the installation when it is its responsibility per the contract or if accomplished under its responsibility.
  • Page 172 This page is intentionally blank ______________...
  • Page 173: Maintenance Records

    MAINTENANCE RECORDS Send photocopy of maintenance record to BRP if needed. PREDELIVERY Serial number: Signature/Print: Mileage / km: Hours: Date: Dealer no: Notes: Refer to vehicle Pre-Delivery Bulletin for detailed installation procedures FIRST INSPECTION Mileage / km: Signature/Print: Hours: Date:...
  • Page 174 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 175 SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print: Hours: Date: Dealer no: Notes: For maintenance schedule refer to Maintenance Information section of this operator's guide SERVICE Mileage / km: Signature/Print:...
  • Page 176 This page is intentionally blank ______________...
  • Page 177: Customer Information

    CUSTOMER INFORMATION ______________...
  • Page 178: Privacy Information

    PRIVACY INFORMATION BRP wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, BRP and its affiliates may use its customer list to distribute marketing and promotional information about BRP and related products.
  • Page 179: Contact Us

    CONTACT US North America www.brp.com 565 de la Montagne Street Asia Valcourt (Québec) J0E 2L0 Canada Room 4609, Tower 2, Grand Gateway 3 Hong Qiao Sa De Cv, Av. Ferrocarril 202 Road Shanghai, Parque Ind. Querétaro, Lote2-B China 200020 76220 Santa Rosa Jáuregui, Qro., Mexico...
  • Page 180: Change Of Address/Ownership

    Notifying BRP, even after the expiration of the limited warranty, is very important as it enables BRP to reach the vehicle owner if necessary, like when safety recalls are initiated. It is the owner’s responsibility to notify BRP.
  • Page 181 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 182 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 183 CHANGE OF ADDRESS/OWNERSHIP ______________...
  • Page 184 CHANGE OF ADDRESS/OWNERSHIP This page is intentionally blank ______________...
  • Page 185 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 186 CHANGE OF ADDRESS/OWNERSHIP NOTES ______________...
  • Page 187 GUIDE DU CONDUCTEUR Séries Maverick Trail T et Maverick Sport T / ANGLAIS FAIT AU / MADE IN CANADA ®TM AND THE BRP LOGO ARE TRADEMARKS OF BOMBARDIER RECREATIONAL PRODUCTS INC. OR ITS AFFILIATES. ©2020 BOMBARDIER RECREATIONAL PRODUCTS INC. ALL RIGHTS RESERVED. PRINTED IN CANADA.

This manual is also suitable for:

Can-am maverick trail sport t

Table of Contents

Save PDF