Horizontal Terminations - Inline Power Flue; Rigid Pipe 102 Mm X 168 Mm - Regency Fireplace Products Greenfire GF950L Owners & Installation Manual

GF950PV
Inline Power Vent Vertical or Horizontal Installation Instructions
CV72EPV / CB72EPV
installation
Inline Power Vent Vertical or Hortizontal Installation Instructions

HORIZONTAL TERMINATIONS - INLINE POWER FLUE

Horizontal Terminations - Inline Power Flue
RIGID PIPE 102MM X 168MM
-5/8" (102mm x 168mm)
Rigid Pipe 4" x 6
Horizontal Terminations - Inline Power Vent
The minimum components required for a basic horizontal
-5/8"
Rigid Pipe 4" x 6
termination are:
1 Horizontal Termination Cap
The minimum components required for a basic horizontal
1 Power Flue Kit
termination are:
1 Rigid Pipe Adaptor
1 Horizontal Termination Cap
1 Length of pipe to suit wall thickness and total flue run
1 Power Vent Kit
(see Table 1)
1 Rigid Pipe Adaptor
Adjustable pipe lengths/slips
1 Vent Reducer
1 Length of pipe to suit wall thickness and total vent run
Wall thickness is measured from the back standoffs to the inside
(see Table 1)
mounting surface of termination cap. Create a level surface to mount the
Adjustable pipe lengths/slips
vent terminal. The Terminal must not be recessed into siding. Measure
the wall thickness.
Wall thickness is measured from the back standoffs to the inside
mounting surface of termination cap. Create a level surface to mount the
vent terminal. The Terminal must not be recessed into siding. Measure
Flat Wall Installation
the wall thickness.
Flat Wall Installation
Wall Thickness
(mm)
Wall Thickness
102mm - 140mm
(inches)
178mm - 216mm
4" - 5-1/2"
254mm - 292mm
7" - 8-1/2"
229mm - 368mm
10" - 11-1/2"
381mm - 597mm
9" - 14-1/2'
15" - 23-1/2"
Important:
Maximum total flue length = 18m with a maximum of six 90
elbows. One 90 elbow = two 45
0
Important:
Maximum total negative flue length = 2.1m.
Maximum total vent length = 72' with a maximum of six 90
One 90 elbow = two 45 elbows.
0 0
Note: Maximum length of 18m is based on overall length of
Maximum total negative vent length = 7'.
combined chimney components.
Note: Maximum length of 72' is based on overall length of combined
Do not run positive flueing after a negative run.
chimney components.
Inline power flue location restrictions:
Do not run positive venting after a negative run.
Minimum 1.2 m from the unit
Minimum 0.3 m prior to an elbow.
Inline power vent location restrictions:
Minimum 0.3 m following an elbow.
Minimum 4 ft (1.2 m) from the unit
Minimum 0.3 m prior to a termination cap.
Minimum 1 ft (0.3 m) prior to an elbow.
Minimum 1.8 m rise from top of unit if there is a negative run.
Minimum 1 ft (0.3 m) following an elbow.
IMPORTANT:The inline power flue must be installed within the confines of the home/structure and must be accessible for future servicing. An access hole
Minimum 1 ft (0.3 m) prior to a termination cap.
as noted in this manual or an attic space would be suitable.
Minimum 6 ft (1.8 m) rise from top of unit if there is a negative run.
Power Vent Kit (Part 946-765)
1 510-994
Power Flue Kit (Part 946-765)
1 510-994
Amount required
Amount required
for install
for install
1 946-765
1 666-945
1 946-206
1 946-206
1 946-523/P
1 946-523/P
1 946-763
946-763
1
1 946-506/P
1 946-506/P
1 911-339
NOTE: Slip section is mandatory.
NOTE: Slip section is mandatory.
920-210
42
920-210
Flue Length Required
(mm)
Vent Length Required
152mm
(inches)
229mm
6"
305mm
9"
279mm - 371mm Adj. Pipe
12"
432mm - 610mm Adj. Pipe
11" - 14-5/8" Adj. Pipe
Table 1
17" - 24" Adj. Pipe
Table 1
0
elbows.
0
0
Rigid Pipe Adaptor
Rigid Pipe Adaptor
102mm x 168mm Rigid Pipe
102mm x 168mm Rigid Pipe Sold separately
Power Flue Kit
Power Vent Kit
Vinyl Siding Standoff
Vinyl Siding Standoff
Astro Cap Termination
Astro Cap Termination
Wall Thimble
Wall Thimble
Vent Guard
Vent Guard
PV Wiring Harness
90 Elbow o
Pipe Length
90 Elbow o
Pipe Length
Rigid Pipe Adaptor
(Part #510-994)
Vent Reducer
(Part #946-606)
Rigid Pipe Adaptor
elbows.
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Sold separately
Included w/Power Flue Kit
6
6
Wall Thimble
Slip Section
Pipe Length
Wall Thimble
Slip Section
Pipe Length
Power Flue Terminal
(Part #946-765)
Adj. Pipe Length/Slip
Power Vent Terminal
Adj. Pipe Length/Slip
Regency GF950L-2 Gas Fireplace
Vent Guard - if required
(Part #946-506/P)
AstroCap (TM)
Termination Cap
Vent Guard - if required
(Part #946-523/P)
(Part #946-506/P)
Standoff
AstroCap (TM)
Termination Cap
(Part #946-523/P)
Standoff
02.20.20
04.01.20