Regency Fireplace Products Greenfire GF950L Owners & Installation Manual page 2

The control box will only learn the Remote ID codes during the first 30 seconds after power is applied
and will ignore this special command from the Remote after the first 30 seconds.
To the New Owner:
To match the control box to the remote, follow the steps below :
Congratulations!
1. Remove a battery from the remote handset.
You are the owner of a state-of-the-art Gas Fireplace by REGENCY
you with all the warmth and charm of a wood fireplace at the flick of a switch. The model GF950L-2 has been
2. Remove main power to the control box by turning off the isolation switch or switch on the GPO to
approved by IAPMO for both safety and efficiency. As it also bears our own mark, it promises to provide you with
economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself
3. Wait 30 seconds (approx.).
with these instructions and the many features of your Regency
4. Reconnect main power to the control box.
5. Immediately put the battery back in the remote & point the remote in the general direction of the
The control box will only learn the remote ID codes during the first 30 seconds after power
6. Press and hold the FAN 1 & FAN 2 buttons simultaneously. The
is applied and will ignore this special command from the remote afterward.
To match the control box to the remote, follow the steps below:
7. Release both buttons.
1. Remove a battery from the remote handset.
8. The display will revert back to the normal off mode display. The
2. Remove main power to the control box by turning off the isolation switch or switch on the
GPO to the heater.
3. Wait 30 seconds (approx.)
9. Press the Off button on the remote. The heater should turn off.
4. Reconnect main power to the control box.
10. Wait approx. 30 seconds turn the on again & check all the functions
5. Immediately put the battery back in the remote & point the remote in the direction of the heater.
6. Press and hold the PROG and FAN buttons simultaneously. The letters "LC" will appear on
Note: To view a step-by-step pairing video please visit
the display indicating ID code transmission.
regency-fire.com.au/Customer-Care/Fireplace-Care-Videos
7. Release both buttons.
Note: The Remote Control Handset has a set of unique ID codes that is
pre-programmed into its memory. This set of ID codes helps to
8. The display will revert to the normal off mode display. The heater should light - spark, burner,
differen-tiate one Remote Control Handset from another so that only
etc. - even though the remote screen says the heater is off.
the control box with a matching ID code will respond to the appropriate
Remote Control Handset.
9. Press the OFF button on the remote. The heater should turn off.
regency.com.au
10. Wait approx. 30 seconds to turn the heater on again & check that all functions work - fan
speed and flame height can be adjusted, etc.
Note: To view a step-by-step pairing video please visit
regency-fire.com.au/Customer-Care/Fireplace-Care-Videos
Note: The remote control handset has a set of unique ID codes that is pre-progarmmed into its
memory. This set of ID codes helps to differentiate one remote control handset from another;
only the control box with a matching ID code will respond to a handset.
Note: The fan cannot be turned off during operation of this appliance.
2
PAIRING YOUR REMOTE CONTROL
the heater.
PAIRING YOUR REMOTE CONTROL
heater.
letters "LC" will appear on the display indicating the ID codes have
been transmitted.
heater should light – spark, burner, etc even though the remote
screen says the heater is off.
work – fan speed can be adjusted, flame height can be adjusted, etc.
. The GF950L-2 has been designed to provide
®
Fireplace.
®
Regency GF950L-2 Gas Fireplace