Operating Instructions; Lighting Instructions; Shutdown Instructions; First Fire - Regency Fireplace Products Greenfire GF950L Owners & Installation Manual

operating instructions

OPERATING
INSTRUCTIONS
Before operating this appliance, proceed through
the following check list.
1. Read and understand these Instructions before
operating this appliance.
2. Check to see that all wiring is correct and
enclosed to prevent possible shock.
3. Check to ensure there are no gas leaks.
4. Make sure the glass door is in place. Never
operate the appliance with the door glass
removed.
5. Verify that all flueing and the cap is unobstructed.
6. Verify log placement.
7. The unit should never be turned off and on
again without a minimum of a 60 second wait.
8. When lighting the appliance, the inside of the
glass may fog up. This will burn off after a few
minutes of operation.
LIGHTING
INSTRUCTIONS
1. Plug the power cord into a power outlet.
2. There is a black, manual, ON/OFF button located
in the bottom left-hand corner of the unit. This
button can be used if there is no remote control.
The flame / fan patterns cannot be changed
when using this button.
3. Non Power Flue: After approximately 3 sec-
onds the spark ignition system will spark for 25
seconds to light the main burner.
Power Flue: After approximately 30 seconds
the spark ignition system will spark for 25
seconds to light the main burner.
4. If the main burner does not light, repeat step
2 to restart the unit. See lighting instructions.
SHUTDOWN
INSTRUCTIONS
1. Press the ON/OFF switch once.
2. Turn off all electric power to the appliance if
service is to be performed.
76

FIRST FIRE

The FIRST FIRE in your heater is part of the
paint curing process. To ensure that the paint
is properly cured, it is recommended that you
burn your fireplace for at least four (4) hours the
first time you use it.
When first operated, the unit will release an
odour caused by the curing of the paint and the
burning off of any oils remaining from manufac-
turing. Smoke detectors in the house may go off
at this time. Open a few windows to ventilate
the room for a couple of hours. The glass may
require cleaning.
NOTE: The main burner will always start on
"HIGH" and resume it's last setting after
20 seconds of operation.
NOTE: When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS STILL HOT!
DO NOT BURN THE APPLIANCE WITH-
OUT THE GLASS FRONT IN PLACE.

REMOTE CONTROL

Use the Regency Remote Control Kit approved
for this unit. Use of other systems may void your
warranty. See page 2 for pairing of remote.
The remote control kit comes with a hand held
transmitter and a wall mounting plate.
1. Choose a convenient location to mount
the hand held transmitter, protection from
extreme heat is very important.
By using the wall mounting plate to house the
transmitter, the remote can also be used as a
wall thermostat.
SUMMARY OF
CONTROLS
On/Off Button
If the unit is switched off, pressing and releasing
this button once will switch the unit on. The unit will
resume its last settings.
If the unit is switched on, pressing and releasing
this button once will switch the unit off.
Flame:
Increase - If the unit is switched on, pressing and
releasing the flame plus (+) button once will increase
the flame height to the next available high setting.
Decrease - If the unit is switched on, pressing
and releasing the flame minus (-) button once will
decrease the flame height to the next available
low setting.
Fan:
Increase - If the unit is switched on, pressing and
releasing the fan plus (+) button once will increase
the fan speed to the next available high setting.
Decrease - If the unit is switched on, pressing and
releasing the fan minus (-) button once will decrease
the fan speed to the next available low setting.
Note: the fan will not completely turn off on this unit.

FAN OPERATION

Pressing and releasing the plus (+) FAN button will
change the fan speed as follows:
LOW -> MEDIUM -> HIGH -> .
Fan cannot be turned off
Pressing and releasing the minus (-) FAN button
will be the reverse of the above.
Fan must be running at all times
when the unit is in operation.

ADJUSTING FLAME HEIGHT

There are six flame settings that can be adjusted
by pressing and releasing the plus (+) and minus
(-) FLAME button.
Regency GF950L-2 Gas Fireplace