Landoll Brillion WFPD38-52 Operator's Manual
  1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Farm Equipment
  5. Brillion WFPD38-52
  6. Operator's manual

Landoll Brillion WFPD38-52 Operator's Manual

Hide thumbs Also See for Brillion WFPD38-52:
Table of Contents

Advertisement

Quick Links

Download this manual
'
Wing Float Pulverizer
Models: WFPD38-52, WFPO38-52,
WFPC38-52 and WFPV50-52
With Scrapers: WFPDS38-52 and WFPVS50-52
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-661-0321

Advertisement

Table of Contents
loading

Related Manuals for Landoll Brillion WFPD38-52

Summary of Contents for Landoll Brillion WFPD38-52

  • Page 1 ‘ Wing Float Pulverizer Models: WFPD38-52, WFPO38-52, WFPC38-52 and WFPV50-52 With Scrapers: WFPDS38-52 and WFPVS50-52 Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-661-0321...
  • Page 2 Manuals for Wing Float Pulverizer WFP 38-52 Manual Number Manual Type F-661 Operator’s Manual F-662 Parts Manual...
  • Page 3 Table of Contents Safety Information Introduction ........... . 1-1 Description of Unit .
  • Page 4 TABLE OF CONTENTS V-Wheel Center Scrapers - Optional ......2-31 V-Wheel Wing Scrapers - Optional ......2-32 Acre Meter Installation - Optional.

  • Page 5: Safety Information

    Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll personal injury or death, damage to the Company, LLC Ag Products on-line registration process.

  • Page 6: Understanding Safety Statements

    TABLE OF CONTENTS Safety • When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the NOTE sign from abrasion, damage, or obstruction from mud, dirt, oil etc. Investigation has shown that nearly 1/3 of all farm accidents are caused by careless use of machinery.

  • Page 7: Maintenance Safety

    TABLE OF CONTENTS Safety Instructions for Towing Protective Equipment Vehicles • Wear protective clothing & equipment appropriate for the job. Avoid loose fitting clothing. The maximum travel speed is the lesser of • Because prolonged exposure to loud noise can cause •...

  • Page 8: Safety Chain

    TABLE OF CONTENTS Safety Chain • Attach the chain to the tractor drawbar support or specified anchor location. Allow only enough slack in Use the safety chain to help control drawn machinery the chain to permit turning. The distance from hitch should it separate from the tractor drawbar.
  • Page 9 2P726 Lower load or relieve hydraulic pressure before loosening fittings. ITEM 1 3K706 LANDOLL COMPANY, LLC 1900 North Street CAUTION Marysville, Kansas 66508 DO NOT ALLOW ANYONE TO RIDE ON THIS IMPLEMENT. DO NOT TRANSPORT AT SPEEDS OVER 20 MPH.

  • Page 10: Decal Locations

    TABLE OF CONTENTS Decal Locations CENTER FRAME FRONT VIEW CENTER FRAME REAR VIEW Figure 1-4: Decal Locations (1 of 5) F-661-0321...
  • Page 11 TABLE OF CONTENTS Figure 1-5: Decal Locations (2 of 5) F-661-0321...
  • Page 12 TABLE OF CONTENTS Figure 1-6: Decal Locations (3 of 5) F-661-0321...
  • Page 13 TABLE OF CONTENTS Figure 1-7: Decal Locations (4 of 5) F-661-0321...
  • Page 14 TABLE OF CONTENTS Front WFP50-52 Rear WFP50-52 Figure 1-8: Decal Locations (5 of 5) 1-10 F-661-0321...
  • Page 15 Chapter 2 TABLE OF CONTENTS Assembly 3. Place a Bearing Insert into each Bearing Half. CAUTION Position a set on each side of the transport Axle Lugs. Attach with 5/8-11 x 13 Bolts, Flat Washers and Do not work on or under this machine unless Locknuts.
  • Page 16 TABLE OF CONTENTS Figure 2-1: Frame and Transport Axle Assembly F-661-0321...
  • Page 17 TABLE OF CONTENTS Center Frame Roller Assembly Installation NOTE Wheel Stop is on the Clamp side of the Roller Assembly NOTE Crowfoot Wheel Rotation Arrow must follow the direction of travel. See Figure 2-2. Roller Assemblies are pre-assembled from the factory with trunnion bearings, shims, and retaining washers.
  • Page 18 TABLE OF CONTENTS Center Frame Center Frame Bearing Hanger Bearing Hanger 3/4-10 Bolt Flat Top Washer Flat Top Washer Loosen 1-8 Bolt Trunnion Shim Stub Shaft Stub Shaft Bearing Washers Mount Center Frame Center Frame Bearing Hanger Bearing Hanger Flat Top Flat Top Washer Washer...
  • Page 19 TABLE OF CONTENTS Trunnion Washer Rear Only Trunnion Bearing Trunnion Bearing Mount Grease Fitting must be oriented to rear of machine FRONT Roller Assembly Bolt,3/4-10 x 2-1/4 Trunnion Bearing Lock Washer,3/4 Mount Trunnion Washer Rear Only Shim Washer Grease Trunnion Fitting Bearing Mount Trunnion Bearing...
  • Page 20 TABLE OF CONTENTS Figure 2-5: Center Frame V-Wheel Roller Installation F-661-0321...

  • Page 21: Drawbar Installation

    TABLE OF CONTENTS Drawbar Installation 1. Attach drawbar to Center Frame with 1 X 8-1/4 Bolts. Place a 1" Flat Washer on each side of the Pins. Secure with 5/16 x 2 Roll Pins and Klik Pins. NOTE 2. Attach turnbuckle to Center Frame Lug with 1 x 6 Pin Note the different Pin lengths for Turnbuckle installation.
  • Page 22 TABLE OF CONTENTS Drawbar Jack, Hose Support and Manual Storage Canister Installation 1. Assemble the Jack Mount to the Jack with the 1/2-13 x 1-1/2 Bolts and Locknuts in the four upper holes. Attach the Jack to the drawbar by slipping the Jack sleeve into the Drawbar sleeve and inserting the Jack 3/4 Pin with Chain.

  • Page 23: Wing Fold Cylinder Installation

    TABLE OF CONTENTS Wing Fold Cylinder Installation 1. Check to make sure that the Cylinder Ball Joints are free to rotate. 2. Cylinder port are front facing. See Figure 2-8. 3. Place the base end of the 5 x 42 Hydraulic Cylinder (WFP38-46) or 5-1/2 x 42 Hydraulic Cylinder (WFP50-52) between each pair of Center Frame Lugs.

  • Page 24: Hydraulic Installation

    TABLE OF CONTENTS Hydraulic Installation Plumb the Hydraulic Circuit CAUTION IMPORTANT Unfold and lower the unit to the ground and relieve The Wing Frames depend upon flow restrictors in system pressure before attempting to repair, adjust the hydraulic manifold to prevent uncontrolled or disconnect components.
  • Page 25 TABLE OF CONTENTS Drawbar A-Frame Handle Hose Clamp Magnet Flat Washer,5/16 Bolt,5/16-18 x 2 Hose Support Magnet Drawbar Figure 2-10: Telescoping Drawbar Magnet Hose Holder F-661-0321 2-11...
  • Page 26 TABLE OF CONTENTS Hydraulic Manifold Installation Fold Shut-Off 1. Lube all O-Ring connections. To operate wing fold shut-off circuit: 2. Fasten Manifold onto Center Frame Bracket with •To close fold shut-off circuit, loosen Jam Nut, turn 5/16-18 x 1" Bolts and Lock Washers. See valve CW fully until valve bottoms.

  • Page 27: Hydraulic Hose Installation

    TABLE OF CONTENTS Hydraulic Hose Installation 4. Attach hoses to Cylinders and Manifold. 5. Install Male Couplers on the ends of the Male O-Ring 1. Install Elbow Fittings into Lift Cylinder Ports. See Hose ends and insert them into the Female Coupler Figures 2-12 and 2-13.
  • Page 28 TABLE OF CONTENTS Figure 2-13: Hydraulic Schematic 2-14 F-661-0321...

  • Page 29: Purging The Hydraulic System

    TABLE OF CONTENTS Purging the Hydraulic System IMPORTANT Unfold and lower the unit to the ground and relieve system pressure before attempting to repair, adjust or disconnect components. WARNING Escaping fluid under pressure can be nearly invisible and have enough force to penetrate the skin causing serious injury.

  • Page 30: Wing Installation

    TABLE OF CONTENTS Wing Installation 1. Assemble the Wings onto the Center Frame. See Figure 2-15. At the rear of the Center Frame, slide the RH or LH Wing Guide Roller into the Center Frame Yoke/Guide. At the front of the Center Frame, place a Spacer on each side of the Spherical Bearing, positioning it between the Center Frame Lugs.
  • Page 31 TABLE OF CONTENTS Wing Link Roller WFP38-46OpWingFrame2016 Bushing,1-1/4 x 14ga Pin,1-1/4 x 9 Roll Pin,5/16 x 2 Bushing,1-1/4 x 14ga Wing Guide Roller Wing Link Roller Bushing, Grease Fitting 1-1/4 x 14ga 1/8 NPT Yoke Cotter Pin, 1/4 x 2-1/2 Roll Pin,5/16 x 2 Slotted Nut, 1-1/4-12...
  • Page 32 TABLE OF CONTENTS Wing Rest Installation 2. Attach the Wing Rest Bumper Pads onto the top of the RH and LH Wing Rest with 3/8-16 x 1-1/2 Flat Head 1. Install the RH and LH Wing Rest to the RH and LH Screws and Locknuts.
  • Page 33 TABLE OF CONTENTS Wing Frame Roller Assembly Installation NOTE Wheel Stop is on the Clamp side of the Roller Assembly. NOTE Roller Axle Assembly clamped end must be on the outer extremity of the Wing. NOTE Crowfoot Wheel Rotation Arrow must follow the direction of travel.
  • Page 34 TABLE OF CONTENTS Bearing Hanger Clamp Locknut,5/8-11 Bearing Hanger Bolt,5/8-11 x 7 Bolt,3/4-10 x 2-1/4 Trunnion Bearing Lock Washer,3/4 Mount Trunnion Washer Rear Only Trunnion Bearing Mount Roller Assembly FRONT Roller Assembly Trunnion Bearing Mount Trunnion Bearing Trunnion Bearing Mount Grease Fitting, must be oriented to rear of machine...
  • Page 35 TABLE OF CONTENTS Bearing Hanger Clamp Locknut,5/8-11 Bearing Hanger Bolt,5/8-11 x 7 Bolt,3/4-10 x 2-1/4 Trunnion Bearing Lock Washer,3/4 Mount Trunnion Bearing Trunnion Washer Mount Rear Only Trunnion Bearing Mount Trunnion Bearing Grease Fitting, must be oriented to rear of machine Outer Roller Assembly Bearing Hanger...
  • Page 36 TABLE OF CONTENTS Warning Lamp Installation 10. Route the “Right” 3 prong cord across the top of inner frame tube to the rear frame, Plug the harness into the right Red Lamp. Route the “Left” 3 prong cord along NOTE the top of front frame, then across the left inner frame, Plug the harness into the left Red Lamp.
  • Page 37 TABLE OF CONTENTS Figure 2-20: Warning Lamp Installation F-661-0321 2-23...
  • Page 38 TABLE OF CONTENTS WFP 38-46 Warning Lamp Bracket Dimensions Warning Warning Lamp Bracket Lamp Bracket Front RH Warning Lamp Bracket 18"±1/2" 18"±1/2" LH Warning Lamp Bracket 12 1/2" SMV Mount Rear Figure 2-21: WFP38-46 Warning Lamp Bracket Dimensions 2-24 F-661-0321...
  • Page 39 TABLE OF CONTENTS WFP 50-52 Warning Lamp Bracket Dimensions 16" Max 16" Max Amber Amber Decal Decal Warning Warning Lamp Bracket Lamp Bracket Front RH Warning 18"±1/2" 18"±1/2" Lamp Bracket LH Warning Lamp Bracket 16" Max 16" Max Decal Decal Orange Orange Decal...
  • Page 40 TABLE OF CONTENTS SMV Installation 1. 1.Attach the SMV Mount to the frame tube 12-1/2" left of center with 5/8-11 U-Bolts, Flat Washers and Locknuts. See Figures 2-21 or 2-22. 2. Attach the SMV sign to the mount with two 5/16-18 X 1 Bolts, Flat Washers and Locknuts.
  • Page 41 TABLE OF CONTENTS Table provided for general use. NOTES: F-661-0321 2-27...
  • Page 42 TABLE OF CONTENTS Center Scrapers - Optional NOTE A scraper can be used as a guide to achieve the 1/4" gap. 1. With the Roller on level ground, attach the Center Frame Scraper Mounts to the Center Frame Front Tube with 1/2-13 U-Bolt and Flange Locknuts. Place a 4 Hole Plate on top and a Scraper Mount Bracket on the bottom of each Center Frame End Cross Tube.
  • Page 43 TABLE OF CONTENTS Scrapers Installed Side View Figure 2-24: Center Scrapers F-661-0321 2-29...
  • Page 44 TABLE OF CONTENTS Wing Roller Scrapers - Optional 3. Adjust the Scrapers so that they are centered between the Notched Wheels along with a 1/4" gap between the Scraper and Notched Wheels. Tighten NOTE all the Wing Scraper Mount Hardware. A scraper can be used as a guide to achieve the 1/4"...
  • Page 45 TABLE OF CONTENTS V-Wheel Center Scrapers - 2. Center Scraper Bars are pre-assembled with Scrapers attached (spaced approximately 6 inches Optional apart). Loosen Three Scraper U-Bolts on each Scraper Bar where the Scraper Bar will attach to the 1. With the Rollers on level ground, attach Scraper Scraper Brackets.
  • Page 46 TABLE OF CONTENTS V-Wheel Wing Scrapers - Optional 3. Wing Scraper Bars are pre-assembled with Scrapers attached (spaced approximately 6 inches apart). 1. With the Rollers on level ground, attach 209842 Wing Loosen Four Scraper U-Bolts on each Wing Scraper Scraper Brackets to the Wing Frame Tube with 5/8-11 Bar where the Scraper Bar will attach to the Wing U-Bolts and Flange Locknuts.
  • Page 47 TABLE OF CONTENTS Figure 2-28: V-Wheel Wing Scrapers WFP 52 - Optional F-661-0321 2-33...
  • Page 48 TABLE OF CONTENTS Acre Meter Installation - Optional existing Trunnion Bearing Bolts and Lock Washers. Fully tighten. 4. Adjust the Acre Meter Switch so the center line of IMPORTANT magnet wheel and pickup switch are horizontally and Unfold and lower machine prior to performing any vertically aligned with a maximum 1/8"...
  • Page 49 TABLE OF CONTENTS Figure 2-30: Acre Meter Installation F-661-0321 2-35...
  • Page 50 TABLE OF CONTENTS Float Lock Kit - Optional 1. Place Wing Float Stops into the Center Frame Wing Guide Slot. See Figure 2-31. 2. Place a Float Stop Spacer on each side of the Wing Float Stops. 3. Place a Wing Float Stop Plate against each Float Lock Spacer.

  • Page 51: Operation

    Chapter 3 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone to ride on the Pulverizer at Always lock the tractor drawbar in the center any time. Allowing a person to ride on the position when transporting the unit. Failure to do machine can inflict serious personal injury or so can result in serious injury or death and cause death to that person.

  • Page 52: Tractor Preparation

    • Make sure the tractor receptacle cover latches over the keyway on the 7-pin connector to hold the The Brillion/Landoll Pulverizer is designed to be pulled by connector in place. a tractor equipped with or without a hammer strap. See •...
  • Page 53 TABLE OF CONTENTS Hitch Lock The Hitch Lock prevents the hitch from moving in either the Spade and Clevis position. Note the different orientation of the Hitch Lock. • Spade position: Insert the Hitch Lock into the clevis end opening. Secure the Hitch Lock with 1 x 9-1/4 Pin and 1/4 x 1-1/4 Lynch Pin.
  • Page 54 TABLE OF CONTENTS Telescoping Drawbar The Telescoping Drawbar is designed to be operated with the Drawbar Extension retracted or extended. See Figure 3-3. The Drawbar must be extended when used as a companion equipment. Pin Retracted Position Position accordingly as drawbar is being extended or retracted Pin Extended Position...

  • Page 55: Hydraulic System

    TABLE OF CONTENTS Hydraulic System 3. On level ground, unfold the wings completely and lower machine to the ground. Make sure the Wing Cylinders are extended completely and the Transport IMPORTANT Axle Cylinder is retracted. The Cylinders should be Unfold and lower the unit to the ground and relieve working smoothly through the stroke, if not purge the system pressure before attempting to repair, adjust, system.

  • Page 56: General Operation

    TABLE OF CONTENTS General Operation 3. Wings should always unfold first, then machine lowers. If not, reduce hydraulic fluid flow. 1. Horsepower requirements will vary due to speed, 4. With machine unfolded and lowered on a level moisture, residue and types of soils. Local dealers surface, adjust the Turnbuckle so the that each Wing can help in making recommendations for your Roller is at the lower 1/3 of its respective Guide Slot.

  • Page 57: Transport Lock

    TABLE OF CONTENTS Transport Lock Road to Field 1. Raise the machine fully. Wings should be folded. 2. Remove Lift Cylinder 20" Transport Lock, Hair Pin NOTE Cotter and 1/2 x 4-1/2 Clevis Pin from Cylinder rod. 20" Transport Lock is standard. 9" Transport Lock is used See Figure 3-7.

  • Page 58: Transporting On A Trailer

    TABLE OF CONTENTS Transporting on a Trailer 5. Disconnect Drawbar from tractor. 6. Retract Telescoping Drawbar. 1. Remove the short (9" long) Transport Lock from 7. Disconnect (Quick Coupling) Hydraulic Hoses and under the Wing Support and place it over the exposed the Ag Harness from where the frame connects to the Transport Axle Cylinder Rod.
  • Page 59 TABLE OF CONTENTS Wings Completely Folded Transport Axle Tire Center Roller Axle Figure 3-9: Transporting on Trailer F-661-0321...
  • Page 60 TABLE OF CONTENTS Table provided for general use. NOTES: 3-10 F-661-0321...

  • Page 61: Scraper Adjustment

    TABLE OF CONTENTS Scraper Adjustment 1. Unfold and Lower Pulverizer on a level surface. 2. Push Notched Wheels against welded Roller Axle End Stops and add Clamp End Spacers if needed. NOTE See Figures 4-9 and 4-10. Notched Roller Wheel Scrapers are optional and 3.
  • Page 62 TABLE OF CONTENTS Electronic Acre Meter Kit Width Press the /FUNC button until the “WIDTH” LED is lit. The The battery operated acre counter operates in one of two number displayed is the length of your implement in feet. modes. In sleep mode, the display is blank, and the To adjust the width, press the UP and DOWN buttons.
  • Page 63 TABLE OF CONTENTS Pulses Width MODEL per 400 FT (Feet) SSPT604 SSP4 SSP5 SSP6 SSP8 SSBP8 SSB8 SSP10 SSBP10 SS10 SSB10 10.0 SSP12 SSBP12 SS12 SSB12 12.0 SSP16 SS16 16.0 SSP108 SS108 SSP110 SS110 10.0 SSP112 SS112 12.0 SSP208/2081 SS208/2081 SSP210/2101 SS210/2101 10.0...
  • Page 64 TABLE OF CONTENTS Transport • Regularly inspect the safety chain for worn, stretched, or broken links and ends. Replace the 1. Check and follow all federal, state, and local safety chain if it is damaged or deformed in any requirements before transporting the Pulverizer. way.

  • Page 65: Maintenance

    Chapter 4 TABLE OF CONTENTS Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.

  • Page 66: Hydraulic Fitting Torque Specifications

    TABLE OF CONTENTS Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
  • Page 67 TABLE OF CONTENTS Manifold Identifier Part Number for 181527 Valve ValveAsm181527 Figure 4-1: Manifold - 181527 Torque Values Manifold - 181527 Torque Values TORQUE FT-LBS ITEM PART NUMBER DESCRIPTION 181527 MANIFOLD, WFP38/52 W/FLOW DVDR (M16351-1) 183662 MANIFOLD,SEQUENCE W/FD 175158 VALVE, #8 NEEDLE 19-21 175159 VALVE,# 10RELIEFP.0.W/REV CHECK...
  • Page 68 TABLE OF CONTENTS Fasteners NOTE The Single Lip Seals should point away from the Hub to Before operating your Brillion machine, check all keep contaminants out and allow grease to pass. hardware for tightness. (See “General Torque Specifications” on page 4-1.) 7.

  • Page 69: Lubrication Maintenance

    TABLE OF CONTENTS Lubrication Maintenance • Every 20 hours lubricate Trunnion Bearings, Cylinder Base Ends, Spherical Bearings and Hinge Pins. • Every 50 hours lubricate Wheel Hubs and CAUTION Turnbuckle. Over lubrication of these bearings can cause • Repack Wheel Hub bearings annually before each premature bearing failure.
  • Page 70 TABLE OF CONTENTS WFP38-52 OpGrease2016 Repack Annually Figure 4-4: Lubrication (2 of 2) F-661-0321...
  • Page 71 Seal kits are available from your Landoll dealer. 3. Check all hydraulic hoses weekly. Look for binding or cracking. Replace all worn or defective parts immediately.

  • Page 72: Purging Hydraulic System

    TABLE OF CONTENTS Purging Hydraulic System Transport Axle Raise and lower the machine from field position to NOTE transport position 2 to 3 times to insure proper functioning of the Hydraulic Circuit. This machine is hydraulically Never unfold the wings past center until all air is out of the controlled by one circuit which controls the lift of the hydraulic circuit, as Free Falling may occur.
  • Page 73 TABLE OF CONTENTS Center Frame Center Frame Bearing Hanger Bearing Hanger 3/4-10 Bolt Flat Top Washer Flat Top Washer Loosen 1-8 Bolt Trunnion Shim Stub Shaft Stub Shaft Bearing Washers Mount Center Frame Center Frame Bearing Hanger Bearing Hanger Flat Top Flat Top Washer Washer...
  • Page 74 TABLE OF CONTENTS Roller Axle Assembly Clamp Tightening After an initial run of 5-10 hours, check the Roller Axle Tighten the Clamp bolts evenly to achieve equal spacing Assemblies to ensure that the wheels are tight to one between clamp section. Torque to 75 Ft-Lbs. Thereafter another.
  • Page 75 TABLE OF CONTENTS Clamp End Spacers - Optional Kit Part Number 201442 - 3/4" Axle Spacer Kit Part Number 201443 - 1/2" Axle Spacer The Clamp End Spacer Kits are used to eliminate space Installation is the same for either kit. between the Axle Clamp and the Wheel Stop.
  • Page 76 TABLE OF CONTENTS Kit Part Number 204831 - 1" Axle Spacer Kit Part Number 204832 - 1-1/4" Axle Spacer Kit Part Number 204833 - 1-1/2" Axle Spacer 1. Place the two Axle Spacers between the Axle Clamp and the Wheel Stop. 2.

  • Page 77: Warning Lamps

    TABLE OF CONTENTS Warning Lamps When plugging in the 7-pin connector: Amber Amber Red Lamp 1. Make sure the tractor has a good clean receptacle, Lamp Lamp free of dirt and corrosion. 2. Make sure the 7-pin connector is inserted ALL the way in.
  • Page 78 TABLE OF CONTENTS Acre Meter Troubleshooting Acre Meter can not change the width or pulse count settings or clear the field and total acres. 1. Check to see if a password needs to be entered by IMPORTANT pressing the *(FUNC) key until the P-Word indicator Acre Meter is dust and splash resistant, under no LED is lit.

  • Page 79: Maintenance Chart

    TABLE OF CONTENTS Maintenance Chart (Subject to change without notice) Initial Run-In 20 Hours 50 Hours Annually Storage Fasteners, Wheel Hub Bolts Grease Wing Hinge Pins Grease Wing Cylinder Base Grease Spherical Bearing Grease Trunnion Bearings Grease Turnbuckle Grease Wheel Hubs Repack Wheel Hub Bearings Adjust Scraper if equipped Tighten Roller Wheels and Clamps...

  • Page 80: Troubleshooting

    TABLE OF CONTENTS Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION Center Roller Bulldozes Wing Hinge Roller is not in the correct Adjust turnbuckle to located Wing Hinge position Roller in the lower 1/3 of Guide Slot Warning Lights do not work Connections loose Connect loose connection Bulbs burned out Change bulb...

  • Page 81: Reference / Specifications

    Chapter 5 TABLE OF CONTENTS Reference / Specifications Model WFP38 WFP40 WFP42 WFP44 WFP46 WFP50 WFP52 Approximate Weight (WFPDS) 20" 11,000 lbs. 11,300 lbs. 11,900 lbs. 12,200 lbs. 12,500 lbs. 12,857 lbs. 13,172 lbs. Notched Ductile Iron (4,990 kg) (5,126 kg) (5,398 kg) (5,534 kg) (5,670 kg)
  • Page 82 TABLE OF CONTENTS Model WFP38 WFP40 WFP42 WFP44 WFP46 WFP50 WFP52 12.5 x 15 FI 12.5 x 15 FI 12.5 x 15 FI 12.5 x 15 FI 12.5 x 15 FI 12.5 x 15 FI 12.5 x 15 FI Tires on 8 Tires on 8 Tires on 8 Tires on 8...
  • Page 83 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 03/15/2013 F-661R1 Initial Release 02/14/2014 F-661R2 Added 50FT-52FT Models 08/01/2016 F-661R3 Changed to Spherical Wing Bearings 10/01/2017 F-661R4 Added V-Wheel Option for 50FT-52FT Models 03/2021 F-661-0321 ECN 46893 - Adjustments to Roller Assemblies...
  • Page 84 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Wing Float Pulverizer Models: WFPD38-52, WFPO38-52, WFPC38-52 and WFPV50-52 With Scrapers: WFPDS38-52 and WFPVS50-52 Operator’s Manual Re-Order Part Number F-661...

This manual is also suitable for:

Brillion wfpo38-52Brillion wfpc38-52Brillion wfpv50-52

Table of Contents