Related Manuals for Landoll Wing Tilloll 876 Series
Summary of Contents for Landoll Wing Tilloll 876 Series
- Page 1 Model 876 Series Wing Tilloll Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-143-0211 02/2011...
-
Page 3: Table Of Contents
Table of Contents Introduction Understanding Safety Statements ..........1-2 Standard Specifications Assembly Instructions Frame and Wing Assembly . - Page 4 Hydraulic Maintenance ............4-9 Lubrication .
-
Page 5: Introduction
Chapter 1 Introduction The Landoll Model 876 Wing Tilloll is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual. -
Page 6: Understanding Safety Statements
INTRODUCTION Understanding Safety Statements You will find various types of safety information on the following pages and on the machine signs (decals) attached to the vehicle. This section explains their meaning. The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED! ... -
Page 7: Standard Specifications
Chapter 2 Standard Specifications 876 SERIES WING TILLOLL MODEL WIDTH TRANSPORT TRANSPORT NO. OF NO. OF 20” ESTIMATED OF CUT WIDTH HEIGHT SHANKS DISC BLADES WEIGHT (LBS.) 876-30 30’-0” 16’-6” * 8’-6” 15,800 876-35 34’-6” 20’-4” 13’-0” 16,700 876-40 40’-0” 17’-9”... - Page 8 STANDARD SPECIFICATIONS LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
- Page 9 STANDARD SPECIFICATIONS LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION) THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
- Page 10 STANDARD SPECIFICATIONS 12 - BLADE DISC ASSY. 11 - BLADE DISC ASSY . 83" SPRAY SHIELD 76" SPRAY SHIELD 3-1/2 22-1/2 37-1/2 11-1/2 86-1/2" REEL 91" REEL 85" HARROW 92-1/2 HARROW 42-1/2 23-3/4 m876-30sp-p1 Figure 2-1: 876-30 Shank Placement Assembly (1 of 2) F-143-0211 Edition...
- Page 11 STANDARD SPECIFICATIONS 11 - BLADE DISC ASSY. 12 - BLADE DISC ASSY . 76" SPRAY SHIELD 3-1/2 83" SPRAY SHIELD 22-1/2 37-1/2 11-1/2 86.5" REEL 91" REEL 11-1/4 92-1/2" HARROW 85" HARROW 23-3/4 42-1/2 47-1/2 m876-30sp-p2 Figure 2-2: 876-30 Shank Placement Assembly (2 of 2)
- Page 12 STANDARD SPECIFICATIONS 12-BLADE DISC ASSY. 8-BLADE DISC ASSY. 7-BLADE DISC ASSY. 83" SPRAY SHIELD 55" SPRAY SHIELD 48" SPRAY SHIELD 3-1/2 22-1/2 37-1/2 37-1/2 6-1/4 91" REEL 115" HARROW 92-1/2" HARROW 72-1/2 23-3/4 47-1/2 m876-35sp-p1 Figure 2-3: 876-35 Shank Placement Assembly (1 of 2) F-143-0211 Edition...
- Page 13 STANDARD SPECIFICATIONS 12 - BLADE DISC ASSY . 7 - BLADE DISC ASSY . 8 - BLADE DISC ASSY. 83" SPRAY SHIELD 37-1/2 48" SPRAY SHIELD 55" SPRAY SHIELD 3-1/2 22-1/2 114" REEL 91" REEL 92-1/2" HARROW 114" HARROW 47-1/2 23-3/4 72-1/2 m876-35sp-p2...
- Page 14 STANDARD SPECIFICATIONS 7 BLADE DISC ASSY. 10 BLADE DISC ASSY. 11 BLADE DISC ASSY. 12-7/18 13-3/8 5-5/8 37.694 22-1/2 37-1/2 55" SHEILD 83" SHEILD 55" REEL 91" REEL 82" REEL 70" HARROW 92-1/2" HARROW 70" HARROW 27-1/2 47-1/2 27-1/2 23-3/4 47-1/4 876-40 shankp1 Figure 2-5: 876-40 Shank Placement Assembly (1 of 2)
- Page 15 STANDARD SPECIFICATIONS 11 BLADE DISC ASSY. 7 BLADE DISC ASSY. 10 BLADE DISC ASSY. 10-9/32 22-1/2 4-5/8 37-1/2 37-1/2 29-1/16 37-1/2 37-1/2 83" SHIELD 55" SHIELD 83" SHIELD 14-7/8 55" REEL 91" REEL 82" REEL 31-7/8 92-1/2" HARROW 70" HARROW 70"...
- Page 16 STANDARD SPECIFICATIONS 2-10 F-143-0211 Edition...
-
Page 17: Assembly Instructions
Chapter 3 Assembly Instructions It is very important that your new 876 Series Wing Tilloll DANGER be properly assembled, adjusted and lubricated before use. Illustrations to assist with the assembly process are To prevent accidental lowering: provided in “Standard Specifications” on page 2-1. 1. - Page 18 ASSEMBLY INSTRUCTIONS Figure 3-1: Frame Assembly F-143-0211 Edition...
- Page 19 ASSEMBLY INSTRUCTIONS Figure 3-2: Wing Assembly (876-30 & 876-35 Models)
- Page 20 ASSEMBLY INSTRUCTIONS Figure 3-3: Wing and Extension Assembly (876-40 Model) F-143-0211 Edition...
-
Page 21: Frame And Wing Assembly
ASSEMBLY INSTRUCTIONS 8. Install 1-1/4 x 1 x 1 steel bushings in cylinder anchor Frame and Wing Assembly bracket. 9. Place frame and wing assembly on stands IMPORTANT approximately 36" high. Read all safety precautions at the front of the section 10. - Page 22 ASSEMBLY INSTRUCTIONS Figure 3-4: Shank, Clamp, and Sweep Assembly F-143-0211 Edition...
-
Page 23: Shank, Clamp, And Sweep Assembly
ASSEMBLY INSTRUCTIONS Shank, Clamp, and Sweep Gauge Wheel Installation Assembly 1. All gauge wheel arms, rockshafts, and hubs come already assembled from the factory. IMPORTANT CAUTION Read all safety precautions at the front of the section before attempting any of the following procedures. Verify that bolt-in spindle is properly assembled 1. - Page 24 ASSEMBLY INSTRUCTIONS Figure 3-6: Hydraulic Lift Assembly (876-30, 876-35, 876-40-C) F-143-0211 Edition...
-
Page 25: Hydraulic Lift Installation (876-30, 876-35, 876-40-C)
ASSEMBLY INSTRUCTIONS Hydraulic Lift Installation 5. Install two 90 adapters in ports #2 and #4 and adapter in port #3 of flow divider valve. Secure flow (876-30, 876-35, 876-40-C) divider valve to flow divider mounting bracket using 5/16-18 x 3 hex head cap screws, flat washers, and IMPORTANT hex lock nuts. - Page 26 ASSEMBLY INSTRUCTIONS Figure 3-7: Hydraulic Lift Assembly (876-40-H) 3-10 F-143-0211 Edition...
-
Page 27: Hydraulic Lift Installation (876-40-H)
ASSEMBLY INSTRUCTIONS Hydraulic Lift Installation 2. Install the slave cylinders on the wing frame ports up, using clevis pin and cotter pins. Connect rod to (876-40-H) gauge wheel arm or rockshaft using cylinder pin bolt and 1/2 split lock washer. IMPORTANT 3. - Page 28 ASSEMBLY INSTRUCTIONS Figure 3-8: Hydraulic Fold Assembly 3-12 F-143-0211 Edition...
-
Page 29: Hydraulic Fold Installation - All Fold Models
ASSEMBLY INSTRUCTIONS Hydraulic Fold Installation - All 2. Install short and flat wing supports on wings using u-bolts and 5/8-11 hex lock nuts. See Figures 2-1 Fold Models through 2-6, and 3-1 through 3-3 for locations. 3. Install 90 elbows with restrictors into base and rod IMPORTANT end of each cylinder. - Page 30 ASSEMBLY INSTRUCTIONS Figure 3-9: Disc Gang and Spray Shield Installation 3-14 F-143-0211 Edition...
-
Page 31: Disc Gang And Spray Shield Installation
ASSEMBLY INSTRUCTIONS Disc Gang and Spray Shield IMPORTANT Installation The distance between last blade on main frame and first blade on wing should be 7-1/2". IMPORTANT IMPORTANT 1. Read all safety precautions at the front of the section before attempting any of the following Disc rod and slotted nut should be tightened to a procedures. - Page 32 ASSEMBLY INSTRUCTIONS Figure 3-10: Center Reel Assembly Installation 3-16 F-143-0211 Edition...
- Page 33 ASSEMBLY INSTRUCTIONS Figure 3-11: Outer Reel Assembly Installation 3-17...
-
Page 34: Reel Assembly Installation
ASSEMBLY INSTRUCTIONS Reel Assembly Installation CAUTION IMPORTANT When working with the reels use care because they rotate freely and can catch an arm, hand, or 1. Read all safety precautions at the front of the foot and can cause severe injury. section before attempting any of the following procedures. - Page 35 ASSEMBLY INSTRUCTIONS 3. Once center and outer reel assemblies are attached to the frame, adjust as necessary to center on frame and to prevent binding. IMPORTANT Distance between reel blade and shank should be 1 inch. 4. Reel bearings lock collars should be installed as described below: a.
- Page 36 ASSEMBLY INSTRUCTIONS Figure 3-12: Harrow Assembly Installation 3-20 F-143-0211 Edition...
-
Page 37: Harrow Assembly Installation
ASSEMBLY INSTRUCTIONS Harrow Assembly Installation 4. Install harrow springs and chains as shown in Figure 3-12 using 1/2-13 x 4 hex head cap screws and hex lock nuts. The top spring is anchored in the 1st hole IMPORTANT from the top. Front lower spring and rear lower spring Read all safety precautions at the front of the section are anchored in the 7th hole from the top of the before attempting any of the following procedures. - Page 38 ASSEMBLY INSTRUCTIONS Figure 3-13: Pull Hitch Installation 3-22 F-143-0211 Edition...
-
Page 39: Pull Hitch Installation - All Other Models
ASSEMBLY INSTRUCTIONS Pull Hitch Installation - All Other Models 1. Install pull hitch assembly to frame using hitch pins, flat washers, and 1/4 x 2-1/2 cotter pins (See Figure 3-13.) 2. Install hitch ring assembly to pull hitch assembly using 1-8 x 8 or 1-8 x 8-1/2 hex head cap screw, flat washer, hitch bushing, and hex lock nut. - Page 40 ASSEMBLY INSTRUCTIONS Figure 3-14: Electrical Installation 3-24 F-143-0211 Edition...
-
Page 41: Warning Lights Installation
ASSEMBLY INSTRUCTIONS Warning Lights Installation 5. Assemble warning light bar and warning light bracket assembly to outer rear of frame as shown in Figure 1. Assemble lights to the warning light bracket using 3-14 using 1/2-13 x 5-1/2 hex head cap screws and 1/4-20 X 1-1/4 hex head cap screws and hex lock hex lock nuts. - Page 42 ASSEMBLY INSTRUCTIONS Figure 3-15: Decal Installation 3-26 F-143-0211 Edition...
-
Page 43: Lubrication
If any decals become unreadable, or are destroyed during use, get replacement decals from your Landoll dealer as soon as possible, and replace them on the machine. 3-27... - Page 44 ASSEMBLY INSTRUCTIONS Notes 3-28 F-143-0211 Edition...
-
Page 45: Operation And Maintenance
Chapter 4 Operation and Maintenance DANGER DANGER Never allow anyone to ride on the 876 Series Always lock the tractor drawbar in the center Wing Tilloll at any time. Allowing a person to ride position when transporting the unit. Failure to do on the machine can inflict serious personal injury so can result in serious injury or death and cause or death to that person. -
Page 46: Tractor Preparation
OPERATION AND MAINTENANCE Tractor Preparation Tilloll Preparation The Landoll 876 Series Wing Tilloll is designed to be 1. Prior to operating the 876 Series Wing Tilloll, inspect pulled by tractor equipped with a double lip or clevis type it thoroughly for good operating condition. -
Page 47: Attaching To The Tractor
OPERATION AND MAINTENANCE Figure 4-2: Transport Locks Attaching to the Tractor Transport 1. Align the tractor drawbar with the machine. Raise or 1. Raise the unit to full transport height. lower the Tilloll ring hitch, as needed, using the 2. Fold the wings. swivel jack. -
Page 48: Field Operation
OPERATION AND MAINTENANCE Field Operation 1. Raise the unit to take the weight off of the transport locks. Remove the transport locks from the lift cylinders (on the main frame only) (See Figure 4-2.) 2. Unfold the wings and extend the fold cylinders completely (See Figure 4-2.) IMPORTANT When folding or unfolding wings, operate tractor... - Page 49 OPERATION AND MAINTENANCE 4. The mainframe and wings must always be level side to side during operation. To level the wings with the mainframe adjustable gauge wheels are provided on the wings. To level the wings: a. Unfold and park the machine on level concrete. b.
-
Page 50: Disc Gang Scraper Adjustment
OPERATION AND MAINTENANCE Spray Shield Adjustment 5. Set the unit working depth (1 - 5 inches) by adjusting the stroke control on the master cylinder. For stability, 1. The spray shields directly behind the disc gang have it is important that the gauge wheels always apply two uses and can be adjusted accordingly. -
Page 51: Harrow Adjustment
OPERATION AND MAINTENANCE Figure 4-6: Harrow Adjustment Harrow Adjustment 1. The harrow on the rear of the machine can be set for a variety of field conditions (See Figure 4-6.) The harrow that is set up according to the assembly instructions for a working depth of 3 - 5 inches. - Page 52 OPERATION AND MAINTENANCE Figure 4-7: Lubrication Points LUBRICATION NO. OF INTERVAL ITEM DESCRIPTION LUBE POINTS (HOURS UNLESS STATED) Radius Rod Gauge Wheel Pivot Pin Disc Gang Bearing Reel Bearing Walking Beam Yearly Wheel Bearing Yearly Note: Lube all points with high grade multi-purpose grease. Table 4-1: Lubrication Schedule F-143-0211 Edition...
-
Page 53: Wheel Bearing Maintenance
Seal kits are available from your Landoll dealer. 3. Check all hydraulic hoses weekly. Look for binding or cracking. Replace all worn or defective parts... - Page 54 OPERATION AND MAINTENANCE Notes 4-10 F-143-0211 Edition...
- Page 55 Chapter 5 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 876 Series Wing Tilloll. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM PROBABLE CAUSE SOLUTION...
- Page 56 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION SHANKS NOT STRAIGHT UP AND Excessive wear at pivot bolt Replace bolt-on shank holder, if needed. DOWN ON FRAME OR HAVE EXCESSIVE WEAR Replace bushing, if needed. SHANK SPRINGS BREAKING Spring pivot bolt too tight Spring pivot bolt must be loose enough to allow spring plug to pivot so spring is not forced to bend.
- Page 57 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE SOLUTION ROCKS JAMMING IN END OF REEL Reel blade too long Cut 1-1/2" off the end of reel blade. AND LOCKING UP REEL Reel angle wrong for terrain Cut blade off at angle toward rear of blade to provide a relief area for rocks.
- Page 58 TROUBLESHOOTING GUIDE Notes F-143-0211 Edition...
- Page 60 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. Model 876 Series Wing Tilloll Operator’s Manual Re-Order Part Number F-143-0211 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...