Option List - Canon Color imageCLASS MF9170c Service Manual
Hide thumbs
Also See for Color imageCLASS MF9170c:
- Basic operation manual (504 pages) ,
- Starter manual (60 pages)
Table of Contents
Advertisement
Chapter 16
Sub item
SPL25407
Setting of thin paper/rough paper
Change the process speed to 4/5 speed. Use the temperature control table for thin paper/rough paper. (Thin paper only)
Do not change the process speed, but change the temperature control table. (Plain paper, Thick paper 2 only)
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL47267
Setting of high-humidity OHT
Decrease the final output value of transfer bias by 100V. (OHT only)
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL47667
Setting of prevention of re-transfer
Decrease the transfer bias for the 3rd/4th station depending on the environment.
(Only when high-humidity OHT/high-humidity gloss film/high-resistance paper/4mil OHT is not specified)
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL34691
Setting for improvement of color misregistration
Rotate the fixing motor in +0.5% speed up to the 10th page. Secure the wait time of 10 seconds when the 1st page is picked up at the time of initial
rotation, mode switching, or toner ejection.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL14682
Setting for prevention of fogging 2
Turn off the pre-exposure operation. Do not add a transfer bias as measures to prevent a bird's foot print on the trailing edge.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL25200
Setting for improvement of OHT transparency
Set the controlled temperature at 180 degC, and perform idling of the fixing machine for 45 seconds before initial rotation.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL53649
Setting of engagement for monochrome mode
Perform full engagement of the ETB.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL35607
Setting of measures for hot offset
Decrease the controlled temperature by 10 degC without exception.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL14660
Not used
SPL65676
Switching of the margin at the lead edge (in the direction of increasing the margin)
Increase the margin at the lead edge of the paper. The standard margin is set if the setting conflicts with that of the decreased margin at the lead edge.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL65677
Switching of the margin at the lead edge (in the direction of decreasing the margin)
Decrease the margin at the lead edge of the paper. The standard margin is set if the setting conflicts with that of the increased margin at the lead edge.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL68676
Switching of the margin at the right/left side (in the direction of increasing the margin)
Increase the margin at the right and left side of the paper. The standard margin is set if the setting conflicts with that of the decreased margin at the
right/left side.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL68677
Switching of the margin at the right/left side (in the direction of decreasing the margin)
Decrease the margin at the right and left side of the paper. The standard margin is set if the setting conflicts with that of the increased margin at the
right/left side.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
SPL25607
Switching of the print mode setting
Switch the print mode for "plain paper" from "Normal" to "Light" as measures for hot offset at overseas countries.
Setting value: 0: OFF, 1: ON
[Factory setting value/Value after RAM clearing: 0]
16.2.5 OPTION
16.2.5.1 OPTION List
imageCLASS MF9170c / imageCLASS MF9150c / imageCLASS MF8450c
<BODY>
Sub item
DFDST-L1
Adjustment of the level of dust detection when DF is used (Correction of an interval between sheets)
When the value is increased, the dust detection level is increased. (This makes it easier to detect the dust causing low-density lines.)
Setting range: 1 to 9999
DFDST-L2
Adjustment of the level of dust detection when DF is used (Detection after a job)
When the value is increased, the dust detection level is increased. (This makes it easier to detect the dust causing low-density lines.)
Setting range: 1 to 9999
16-16
COPIER > FUNCTION > SPLMAN
Description
T-16-22
COPIER > OPTION > BODY
Description
0020-2016
Advertisement
Table of Contents
