Alarm Code; Alarm Code (Adf); Fax Error Codes; Outline - Canon Color imageCLASS MF9170c Service Manual

14.4 Alarm Code

14.4.1 Alarm Code (ADF)

imageCLASS MF9170c / imageCLASS MF9150c / imageCLASS MF8450c
Code Name
0003H Separation NG alarm

14.5 Fax Error Codes

14.5.1 Outline

14.5.1.1 Error Code Outline

imageCLASS MF9170c / imageCLASS MF9150c / imageCLASS MF8450c
An error code is used to indicate a fault in a machine, and is indicated in the machine's LCD or reports, showing the nature (symptoms) of the fault. Using the error
code, the user or the service man can readily find out how to correct the fault by simply referring to the User's Manual or service manual.
An error code may be either of the following two types:
- User Error Codes
A fault indicated as a user error code is one that can easily be corrected by the user, as by operating the machine. It takes the form of "#+number."
- Service Error Codes
If a fault calls for a service man for correction, it is indicated as a service man error code in the form of "##+number" or "SYSTEM ERROR E+number."
MEMO:
- A service error code expressed in the form of "##+number" will not appear on the LCD, Error Tx Report, or Activity Report while the machine remains in factory
default state. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01 to '1'.
- Display only the error codes which are newly incorporated in this machine as well as which require remedies unique to the product. For the causes and
countermeasures of other error codes, refer to the separate G3/G4 Facsimile Error Code List (Rev. 2).

14.5.2 User Error Code

14.5.2.1 User Error Code

imageCLASS MF9170c / imageCLASS MF9150c / imageCLASS MF8450c
No. Tx/Rx
#0001 [Tx]
#0003 [Tx]
#0005 [Tx]
#0012 [Rx]
#0018 [Tx]
#0037 [Rx]

14.5.3 Service Error Code

14.5.3.1 Service Error Code
imageCLASS MF9170c / imageCLASS MF9150c / imageCLASS MF8450c
No. Tx/Rx
##0100 [Tx]
##0101 [Tx]
##0102 [Tx]
##0104 [Tx]
##0106 [Rx]
##0107 [Rx]
##0109 [Tx]
##0114 [Rx]
##0200 [Rx]
##0201 [Tx]
##0224 [Tx]
##0228 [Rx]
##0232 [Tx]
Sensor No.
SR719 The leading edge of paper does not reach the ADF paper trailing edge sensor (SR719) within
3.2 sec after the ADF pickup motor starts positive rotation.
Description
an original has jammed.
tine-out for copying or sending/receiving a single page has occurred.
time-out for initial identification (T0/T1) has occurred.
recording paper is absent at the other party.
auto call initiation has failed.
image memory overflow at time of reception has occurred.
Description
at time of transmission, the procedural signal has been transmitted more than specified.
the modem speed does not match that of the other party.
at time of transmission, fall-back cannot be used.
at time of transmission, RTN or PIN is received.
at time of reception, the procedural signal is received for 6 sec while in wait for the signal.
at time of reception, the transmitting party cannot use fall-back.
at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sent
more than specified.
at time of reception, RTN is transmitted.
at time of reception, no image carrier is detected for 5 sec.
DCN is received outside the normal parity procedure.
Error has occurred on transmission procedural signal.
Error has occurred on images' information control.
encoding error has occurred.
T-14-8
Description
T-14-9
T-14-10
Chapter 14
0020-9550
0020-4435
0020-4437
0020-4439
14-9