Q307: Open Collector #1 Output; Q308: Open Collector #2 Output; Q309: Allow Backlight Always On; Q401: Radio Modem Network Failure Time, In Minutes - 2gig Technologies EDGE Installation Manual

»
† Audible: Turns the feature ON. This makes the Fire button visible on the Alarm screen. The system sounds a loud, patterned warning
siren after the user activates a fire alarm.
Q303: Emergency key
Configures the system to show or hide the Emergency button on the Alarm screen of the 2GIG EDGE Panel's touchscreen. When set to Audible, the
button is visible and the system emits a loud, patterned warning siren when a user sets off an emergency alarm on the 2GIG EDGE Panel.
Choose one of these options:
»
Disabled: Turns the feature OFF and hides the Emergency button from the Alarm screen.
»
† Audible: Turns the feature ON. This makes the Emergency button visible on the Alarm screen. The system sounds a loud, patterned
warning siren after the user activates an emergency alarm.
Q304: On-Board Camera
Configures the system to turn off the On-Board camera used any of panel features such as "snapshots" and "Face Recognition".
Choose one of these options:
»
† Enabled: On-Board camera is on. Camera turns on momentarily when panel features, such as face recognition or photo snapshot,
are active
»
Disabled: On-Board camera is turned off. All features using On-Board camera are unavailable.
NOTE: This is a global setting.
Q305: Temperature display units
Specifies the temperature scale used by the system to display weather forecasts on the touchscreen.
NOTE: Weather forecasts are only available on the 2GIG EDGE Panel when enabled by the service provider.
Choose one of these options:
† Fahrenheit: Displays information using the Fahrenheit temperature scale.
Celsius: Displays information using the Celsius temperature scale.
Q306: Configuration change acknowledgement
Configures the system to annunciate or suppress annunciation of the panels status after a reboot or panel programming.
»
† Enabled: The panel will announce the panel status when the panel powers up, reboots, or exits programming.
»
Disabled: This option will suppress the annunciation of the panel status when the panel powers up, reboots, or exits programming.
NOTE: When any changes are made to the panel from Alarm.com, including programming questions, changes to sensors, adding,
deleting, or changing users, the 2GIG EDGE panel will announce its status. Example: "System disarmed, ready to arm." Changing Q306
to Disabled will suppress this annunciation from the panel.
NOTE: Q306 will only affect the annunciation of the status of the panel, as described above. Q306 will not affect any other annunciations
of the 2GIG EDGE panels.

Q307: Open collector #1 output

Defines output mode for the external device connected to the OCL1 position of the 2GIG EDGE Panel's terminal block. See Control Panel Wiring
Diagram,
page 24.
NOTE: For compliance with ANSI/SIA CP-01-2010, you must set Open Collector Output #1 to 11 - Follows Internal Sounder Alarm.
NOTE: If you enabled a keyfob auxiliary button to trigger the 2GIG EDGE Control Panel's Open Collector #1, make sure this question is set
to 00 Disabled, "Program a Keyfob."
Choose one of these options:
Code Open Collector Output Code
00 Disabled 06
01 Activated When Armed 07
02 Activated When Disarmed 08
03 Activated on FTC (Failure to Communicate 09
04 Activated on Siren Supervision † 11
05 Activated on Radio Fault 12
2GIG EDGE Installation Guide
Open Collector Output
Activated on Burglary Alarm
Activated on Fire Alarm
Activated on Any Alarm
Activated on Any System Trouble
Follows Internal Sounder Alarm
Follows Exit/Entry Beeps
50

Q308: Open collector #2 output

Defines the output mode for the external device connected to the OCL2 position of the 2GIG EDGE Panel's terminal block. See Control Panel
Wiring Diagram,
page 24.
NOTE: The factory default setting for
Open Collector Output #2 is 00-Disabled
Choose one option from (above).
Open Collector Output Table

Q309: Allow backlight always on

Configures the system to always display the option to leave the touchscreen's backlight on. This is useful when users want to demonstrate panel
features, without the system backlight timing out.
IMPORTANT: Leaving the backlight ON for extended periods of time may result in image retention. To avoid this, it is recommended that
you only enable this feature when the panel is intended for use as a demonstration system.
Choose one of these options:
»
Enabled: The backlight for the touchscreen is always ON.
»
† Disabled: The backlight for the touchscreen dims automatically after 60 seconds of inactivity.
NOTE: Timeout has to be set in Screen Settings in order for this option to take affect.
Troubles

Q401: Radio modem network failure time, in minutes

Configures the system to display a trouble alert on the touchscreen when the system loses its cellular radio network connection. The number of
minutes you specify here defines the amount of down time that must pass before the system issues a trouble alert report. Once network service is
restored for five (5) minutes, the trouble alert condition automatically clears itself.
Choose one of these options:
»
0 Minutes: Turns the feature OFF. The system does not issue a trouble alert
»
1-255 Minutes: Turns the feature ON. Use the touchscreen's numeric keypad to enter the number of minutes between 1 and 255.
»
† 30 Minutes: Turns the feature ON and issues a trouble alert on the 2GIG EDGE Panel after 30 minutes of down time.

Q402: Radio network failure causes trouble

Configures the system to display a trouble alert on the touchscreen when it logs a trouble alert condition with the cellular network connection.
The 2GIG EDGE Panel will display an alert message on the touchscreen after the number of minutes specified in
above expires.
time, in minutes (0-255)
Choose one of these options:
»
† Enabled: Turns the feature ON. The 2GIG EDGE Panel display a visual trouble indicator after a cellular radio network failure.
»
Disabled: Turns the feature OFF. The 2GIG EDGE Panel will not display a visual indicator after a cellular radio network failure.
NOTE: Regardless of the setting selected here, a radio network failure will always be logged in the System History.
Once the network connection is restored, the system automatically clears the visual indicator. A record of the trouble alert condition is stored in
the System History.

Q403: Radio network failure reports

Configures the system to transmit a trouble report to the Central Station when the system detects a cellular radio network failure.
Choose one of these options:
»
† Enabled: Turns the reporting feature ON. The 2GIG EDGE Panel will transmit a trouble report to the Central Station after a cellular
radio network failure.
»
Disabled: Turns the reporting feature OFF. The 2GIG EDGE Panel will not transmit a trouble report to the Central Station after a cellular
radio network failure.

Q404: Broadband network failure time in minutes

Configures the system to display a trouble alert on the touchscreen when the system loses its broadband network connection. The number of
minutes you specify here defines the amount of down time that must pass before the system issues a trouble alert report. Once the broadband
connection is restored for five (5) minutes, the trouble condition automatically clears itself.
Choose one of these options:
»
0 minutes: Turns the feature OFF. The system does not issue a trouble alert
»
1-255 minutes: Turns the feature ON. Use the touchscreen's numeric keypad to enter the number of minutes between 1 and 255
»
† 30 Minutes: Turns the feature ON and issues a trouble alert on the 2GIG EDGE Panel after 30 minutes of down time.
.
Q401: Radio modem network failure
Copyright © 2021 Nortek Security & Control LLC
51