Xerox B205 Service Manual page 34

07-600 Paper Tray Empty RAP
BSD-ON:BSD 1
Control Panel Fault Displayed
B205: All trays empty
B215: The Device is Out of Paper
The Tray 1 Empty sensor and the Registration sensor failed to detect paper in the paper trays.
Initial Actions
Ensure that paper is loaded in the trays. Clear any jammed sheets. (Refer to Section 11 in the
Xerox® B215/B205 User Guide for detailed instructions on jam clearance.)
Do not perform repair activities with the power on or electrical power supplied to the
machine. The machine could activate and cause serious personal injury when the power
is on or electrical power is supplied.
DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de
graves blessures.
AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare
gravi ferite.
VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.
AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente.
La máquina podría activarse y ocasionar daños personales graves.
Procedure
Check the Exit Sensor, PL 4.5 Item 3, and the Paper Feed Sensor PWB,
contamination. The sensors are free of contamination.
Y N
Clean the sensors.
Refer to the following RAPs:
• 07-500 Manual Feed Slot Paper Empty Fault RAP
• 07-110 Paper Tray 1 Empty Fault RAP
Initial Release
Xerox® B205/B215 Multifunction Printer Service Manual
WARNING
PL 4.4 Item
08-100 Paper Feed - Tray 1 RAP
BSD-ON:BSD 1
Control Panel Fault Displayed
B205: Jam inside machine
B215: Jam in the Device
The lead edge was not detected by the Paper Feed Sensor.
Initial Actions
Clear any jammed sheets. (Refer to Section 11 in the Xerox® B215/B205 User Guide for
detailed instructions on jam clearance.)
Do not perform repair activities with the power on or electrical power supplied to the
machine. The machine could activate and cause serious personal injury when the power
is on or electrical power is supplied.
DANGER: Ne pas effectuer de dépannage avec le contact principal activé ou avec l'ali-
mentation électrique appliquée à la machine: celle-ci pourrait démarrer et causer de
graves blessures.
AVVERTENZA: Non effettuare alcuna riparazione con la macchina accesa o con l'ali-
mentazione elettrica inserita. La macchina potrebbe avviarsi all'improvviso e causare
gravi ferite.
VORSICHT: Es dürfen keine Reparaturarbeiten durchgeführt werden, solange das Gerät
eingeschalten oder mit der Stromquelle verbunden ist. Das Gerät kann u.U in den Aktiv-
Zustand übergehen und somit erhebliche körperliche Schäden verursachen.
AVISO: No realice reparaciones con la máquina encendida o conectada a la corriente.
La máquina podría activarse y ocasionar daños personales graves.
Procedure
20, for Check the Tray 1 Paper Feed Sensor Actuator. The Actuator moves freely.
Y N
Install a new Feed Sensor Actuator,
Check the position of the jammed sheet. The lead edge reached the Retard Roll.
Y N
Enter Diagnostic Mode, GP 1, [Machine Test, Diagnostics Mode, DC330 Component
Control, 101-Clutch, Tray 1 Pick up] to engage the drive to pick up paper from tray 1
The clutch engages.
Y N
1. Check the circuit between the Feed Clutch and the HVPS PWB for an open or
short circuit.
2. Install a new Feed Clutch,
Check the Feed Sensor Actuator,
Y N
Install a new Feed Sensor Actuator,
A B
July 2019
2-13
WARNING
PL 4.4 Item 18.
PL 4.1 Item 4.
PL 4.4 Item 18. The actuator moves freely.
PL 4.4 Item 18.
Status Indicator RAPs
07-600 , 08-100