Adamson IS Series Rigging Manual
  1. Manuals
  2. Brands
  3. Adamson Manuals
  4. Speaker System
  5. IS Series
  6. Rigging manual

Adamson IS Series Rigging Manual

Line array
Hide thumbs Also See for IS Series:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Adamson IS Series

Summary of Contents for Adamson IS Series

  • Page 2 Distribution Date: March 1st, 2020 • Copyright 2020 by Adamson Systems Engineering Inc., all rights reserved This manual must be accessible to the person operating this product. As such, the product owner must store it in a safe place and make it available upon request to any operator.

  • Page 3: Table Of Contents

    Visual inspection and approval of the point of suspension is the responsibility of the installation personnel • Rigging instructions such as Load and Centre of Gravity can be found by using Adamson’s Blueprint AV software. • Use only with the rigging frames/accessories specified by Adamson, or sold with the loudspeaker system.
  • Page 4 Installation of these systems should be performed by at least two qualified technicians. • When suspending any Adamson product, the proper PPE (personal protective equipment) should be worn. • All local laws and by-laws must be adhered to when suspending these products.

  • Page 5: Rigging Applications

    Extended Beam Moving Point Extended Beam Suspension frame to hang up Extension beam for larger Moving point beam to achieve to 4x IS10 enclosures angles exact angles with a single pick point Adamson Systems Engineering | IS-Series Rigging Manual Page 5...
  • Page 6 3x IS7 suspended under 1x IS7 Micro Frame 6x IS7 suspended under 1x IS7 & IS118 Rigging Frame 2x IS119 and 6x IS10 suspended using 2x IS10 & IS119 Rigging Frames Adamson Systems Engineering | IS-Series Rigging Manual Page 6...

  • Page 7: Rigging Components

    Extended Beam (930-0021) or Moving Point Extended Beam (930-0033) is necessary. Component Quantity Rigging Link Stacking Link Quick-Release Pin Lifting Plate M6 Screw 305 mm / 12 in Ø 12 mm / 0.63 in 528 mm / 20.8 in Adamson Systems Engineering | IS-Series Rigging Manual Page 7...
  • Page 8 IS7 Micro Frame. Refer to Blueprint AV for safety limits. Component Quantity Quick-Release Pin Lifting Plate M6 Screw Ø 12 mm / 0.63 in 527 mm / 20.75 in Adamson Systems Engineering | IS-Series Rigging Manual Page 8...
  • Page 9 Extended Beam (930-0021) or Moving Point Extended Beam (930-0033) is necessary. Component Quantity Rigging Link Stacking Link Quick-Release Pin Lifting Plate M6 Screw Rear Link Ø 12 mm / 0.63 in 396 mm / 15.6 in 737 mm / 29 in Adamson Systems Engineering | IS-Series Rigging Manual Page 9...
  • Page 10 IS10 Micro Frame. Refer to Blueprint AV for safety limits. Component Quantity Quick-Release Pin Lifting Plate M6 Screw Ø 12 mm / 0.63 in 737 mm / 29 in Adamson Systems Engineering | IS-Series Rigging Manual Page 10...
  • Page 11 When using the Extended Beam, ensure the weight of the suspended array falls within the load limits of the Rigging Frame being used. Component Quantity Extended Beam Plate Quick-Release Pin 1151 mm / 45.3 in Adamson Systems Engineering | IS-Series Rigging Manual Page 11...
  • Page 12 When using the Moving Point Extended Beam, ensure the weight of the suspended array falls within the load limits of the Rigging Frame being used. Component Quantity Rigging Pin Second Point Link 813 mm / 32 in Adamson Systems Engineering | IS-Series Rigging Manual Page 12...

  • Page 13: Rigging Procedures

    3. Affix the IS7 enclosure through the front tab to the bottom front hole of the frame using the T25 Torx screws (a) removed earlier. A torque setting of 6.5 Nm is to be used. Adamson Systems Engineering | IS-Series Rigging Manual Page 13...
  • Page 14 T25 Torx screws from the bottom front holes of the affixed IS7. Lower the frame until the upper enclosure’s bottom front hole (d) is in-line with the front tab (b) of the second IS7 enclosure. Adamson Systems Engineering | IS-Series Rigging Manual Page 14...
  • Page 15 2 fig. 1 8. Repeat steps 5 through 7 until the desired amount of enclosures are affixed in the array. Adamson Systems Engineering | IS-Series Rigging Manual Page 15...

  • Page 16: Suspending Is7 Micro Frame

    IS7 Micro Frame to the IS7 enclosure front tab. Use a torque setting of 6.5 Nm. 4. Connect additional IS7s as per steps 5 thru 8 of 4.1 Suspending IS7. Adamson Systems Engineering | IS-Series Rigging Manual Page 16...

  • Page 17: Ground Stacking Is7

    Torque setting of 6.5 Nm is to be used. 4. Lower the 4x Rigging Frame rigging links on each corner of the Rigging Frame, removing and loosening the T25 Torx screws as necessary. Adamson Systems Engineering | IS-Series Rigging Manual Page 17...
  • Page 18 6. Connect the rigging links to the IS118 using the T25 screws removed earlier. 8 screws are needed in total, 2 bolts per corner rigging link. Use a torque setting of 6.5 Nm. Adamson Systems Engineering | IS-Series Rigging Manual Page 18...
  • Page 19 IS7 Ground Stacking Rigging Frame Angle Chart 1 +3° +1° -2° -4° -6° 2 +5° +2° -1° -3° -5° 3 +6° +4° +2° 0° -2° fig. 3 * Tolerance of specified angles +/- 0.25° Adamson Systems Engineering | IS-Series Rigging Manual Page 19...
  • Page 20 Blueprint. Make sure that both left and right rear rigging positions are set to the identical fig. 1 fig. 2 angle. 10. For additional IS7s, repeat step 9. Adamson Systems Engineering | IS-Series Rigging Manual Page 20...

  • Page 21: Suspending Is10

    3. Affix the IS10 enclosure through the front tab to the bottom front hole of the Rigging Frame using the T45 Torx screws (a) removed earlier. A torque setting of 6.5 Nm is to be used. Adamson Systems Engineering | IS-Series Rigging Manual Page 21...
  • Page 22 T45 Torx screws from the bottom front holes of the affixed IS10. Lower the frame until the upper enclosure’s bottom front hole (d) is in-line with the front tab (b) of the second IS10 enclosure. Adamson Systems Engineering | IS-Series Rigging Manual Page 22...
  • Page 23 4 fig. 5 8. Repeat steps 5 through 7 until the desired amount of enclosures are affixed in the array. Adamson Systems Engineering | IS-Series Rigging Manual Page 23...

  • Page 24: Suspending Is10 Micro Frame

    IS10 Micro Frame to the IS10 enclosure front tab. Use a torque setting of 6.5 Nm. 3. Connect additional IS10s as per steps 5 thru 8 of 4.4 Suspending IS10 to a maximum of 4. Adamson Systems Engineering | IS-Series Rigging Manual Page 24...

  • Page 25: Ground Stacking Is10

    Torque setting of 6.5 Nm is to be used. 4. Lower the 4x Rigging Frame rigging links on each corner of the Rigging Frame, removing and loosening the T45 Torx screws as necessary. Adamson Systems Engineering | IS-Series Rigging Manual Page 25...
  • Page 26 Rigging Frame with the sides of the IS119. 6. 2x T45 screws per corner connect each rigging link to the IS119. Use torque setting of 6.5 Nm. Adamson Systems Engineering | IS-Series Rigging Manual Page 26...
  • Page 27 Rigging Frame. Use the T45 Torx screws removed earlier to connect the IS10 to the Rigging Frame stacking links. A torque setting of 6.5 Nm is to be used. Adamson Systems Engineering | IS-Series Rigging Manual Page 27...
  • Page 28 IS10 Ground Stacking Rigging Frame Angle Chart 1 +0° -2° -4° -6° 2 +3° +1° -1° -3° +4° +2° 0° fig. 6 fig. 4 fig. 5 * Tolerance of specified angles +/- 0.25° Adamson Systems Engineering | IS-Series Rigging Manual Page 28...
  • Page 29 Blueprint. Make sure that both left and right rear rigging positions are set to the identical angle. 10. For additional IS10s, repeat step 9. fig. 4 fig. 5 Adamson Systems Engineering | IS-Series Rigging Manual Page 29...

  • Page 30: Suspending Is118

    5 2. Remove all links from the Rigging Frame by removing the T25 Torx screws (a) affixing them in place. Place the screws in a secure place for future use. Adamson Systems Engineering | IS-Series Rigging Manual Page 30...
  • Page 31 6. Lower the flown subwoofer onto the second subwoofer and affix them together using the T25 Torx screws set aside in the previous step. 7. Repeat steps 4 through 6 for any further subwoofers in the array. Adamson Systems Engineering | IS-Series Rigging Manual Page 31...

  • Page 32: Suspending Is7 Below Is118

    2. Prepare the bottom IS118 by affixing the Rigging Links so that the 2 screw holes are affixed to each corner of the subwoofer with T25 screws. Adamson Systems Engineering | IS-Series Rigging Manual Page 32...
  • Page 33 3. Affix the Rigging Frame to the Rigging Links. 4. Line up the IS7 enclosure front tab so that it will match to the bottom front hole of the Rigging Frame. Adamson Systems Engineering | IS-Series Rigging Manual Page 33...
  • Page 34 “E” hole on the IS7 rigging link. 7. For additional IS7s, follow Suspending IS7 steps 5 through 7 until the desired amount of enclosures are affixed in the array. Adamson Systems Engineering | IS-Series Rigging Manual Page 34...

  • Page 35: Suspending Is119

    6 2. Remove all links from the Rigging Frame by removing the T45 Torx screws (a) affixing them in place. Place the screws in a secure place for future use. Adamson Systems Engineering | IS-Series Rigging Manual Page 35...
  • Page 36 6. Lower the flown subwoofer onto the second subwoofer and affix them together using the screws set aside in the previous step. 7. Repeat steps 4 through 6 for any further subwoofers in the array. Adamson Systems Engineering | IS-Series Rigging Manual Page 36...

  • Page 37: Suspending Is10 Below Is119

    Do not remove the 2 Rear Rigging Links. 2. Prepare the bottom IS119 by affixing the Rigging Links so that the 2 screw holes are affixed to each corner of the subwoofer with T45 screws. Adamson Systems Engineering | IS-Series Rigging Manual Page 37...
  • Page 38 3. Affix the Rigging Frame to the Rigging Links. 4. Line up the IS10 enclosure front tab so that it will match to the bottom front hole of the Rigging Frame. Adamson Systems Engineering | IS-Series Rigging Manual Page 38...
  • Page 39 6.5 Nm is to be used. of the IS10 up and affix them to the top hole on the frame through the “E” hole on the IS10 rigging link. Adamson Systems Engineering | IS-Series Rigging Manual Page 39...

This manual is also suitable for:

Is7Is7bIs10Is10bIs10nIs10nb ... Show all

Table of Contents