Adamson IS Series User Manual
Hide thumbs
Also See for IS Series:
- Rigging manual (39 pages) ,
- User manual (9 pages) ,
- User manual (8 pages)
Advertisement
Quick Links
Table of Contents
Safety & Warnings
Read these instructions, keep them available for reference.
This manual can be downloaded from
Heed all warnings and follow all instructions.
A qualifi ed technician must be present during the installation and use of this product. This product
is capable of producing extremely high sound pressure levels and should be used according to the
specifi ed local sound level regulations and good judgement. Adamson Systems Engineering will
not be liable for damages caused by any possible misuse of this product.
Servicing is required when the loudspeaker has been damaged in any way, such as when the
loudspeaker has been dropped; or when for undetermined reasons the loudspeaker does not
operate normally.
Protect the cabling from being walked on or pinched.
Read the appropriate IS-Series Rigging Manual before installing the product.
Pay attention to rigging instructions included in both Blueprint AV™ and the IS-Series Rigging
Manual.
Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker
system.
This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around
the enclosure with data storage devices such as hard drives.
In an effort to continuously improve its products, Adamson releases
updated accompanying software, presets and standards for its products.
Adamson reserves the right to change the specifications of its
products and the content of its documents with no prior notice.
Adamson Systems Engineering |
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
______________________________________________________________________________________
IS10p User Manual
3
4
5
6
7
8
Page 1
Advertisement
Related Manuals for Adamson IS Series
Summary of Contents for Adamson IS Series
- Page 1 Pay attention to rigging instructions included in both Blueprint AV™ and the IS-Series Rigging Manual. Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker system. This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around the enclosure with data storage devices such as hard drives.
- Page 2 IS10p User Manual Distribution Date: March 1st, 2021 Copyright 2021 by Adamson Systems Engineering Inc.; all rights reserved This manual must be accessible to the person operating this product. As such, the product owner must store it in a safe place and make it available upon request to any operator.
-
Page 3: Table Of Contents
Pay attention to rigging instructions included in both Blueprint AV™ and the IS-Series Rigging Manual. Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker system. This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around the enclosure with data storage devices such as hard drives. -
Page 4: Product Introduction
The high frequency waveguide is rotateable in increments of 90°. The nominal dispersion pattern is 70° x 40° (HxV). A 100° x 50° high frequency waveguide is also available. • Adamson’s use of proprietary techologies such as Advanced Cone Architecture give the IS10p an extremely high maximum SPL level of 139 dB. •... -
Page 5: Wiring
Pins 1+/- are connected to the 2x ND10-LM MF transducers, wired in parallel. • Pins 2+/- are connected to the NH3-8 HF transducer. PARALLEL IS10p Jackplate IS10pb Jackplate PARALLEL INPUT PARALLEL INPUT IS10p & IS10pb Internal Wiring (IS10pb only has one input) IS10p User Manual Adamson Systems Engineering | Page 5... -
Page 6: Amplification
IS10p Amplification The IS10p is paired with Lab.gruppen D-Series amplifiers. Maximum quantities per amplifier are shown below. For a master list, please refer to the Adamson Amplification Chart, found on the Adamson website. https://adamsonsystems.com/support/downloads-directory/is-series/is10p/331-max-enclosures-per- amplifier-v5-0-1-7-1-2-1-1 D40:4L D80:4L 2x IS10p 4x IS10p... -
Page 7: Presets
The Adamson Load Library, found on the Adamson website, contains presets designed for a variety of IS10p applications. Furthermore, there are presets designed to pair with either Adamson subs, or Adamson Line Arrays. For a master list, please refer the Adamson PLM & Lake Handbook, found on our website. -
Page 8: Technical Specifications
70° x 40° (optional 100° x 50° available) Maximum Peak SPL ** 139 dB Components LF 2x ND10-LM 10” Neodymium Driver Components HF Adamson NH3-8 3” Diaphragm / 1.4” Exit Com- pression Driver Nominal Impedance LF 8 Ω (2x 16 Ω) Nominal Impedance HF 8 Ω...