User Maintenance Instructions; Operating And Fault Code Diagnosis; Red Coloured Led; Tri-Coloured Led - Seeley Climate Wizard CW-P15 Installation Operation & Maintenance

USER MAINTENANCE INSTRUCTIONS

OPERATING AND FAULT CODE DIAGNOSIS

There are 2 methods for confirming the cooler operation and
diagnosing faults on the cooler.
A. LED Display
There are two LED indicators on the main control board (located
in the control box) - refer below.
• Tri-Colour LED (upper LED) is used as an operational and
fault indicator. NOTE: Tri-colour LED double flashing Green
(every 2 seconds) = Normal Operation
• Red LED (lower LED) is used to indicate the condition of water
salinity and configuration of the water management system.
B. Wall Control Display
If controlled by a MagIQcool Wall Control, the wall control can
be used to enter the fault code history log, which details the last
four (4) faults in the system and the last four (4) types of faults
that have occurred.
The fault code history log may be entered at any time after the
cooler power has been turned ON. The fault code history log is
entered via the wall control using the following method:
1. Whilst the wall control is in "OFF" state, push and hold
"AUTO" and UP "▲" buttons simultaneously for at least one
(1) second.
2. After one (1) second "F1" and the word "Param" will be
displayed.
3. Pressing "AUTO" button will change "F1" to the current or
last fault code number e.g., "01" and the word "Param" will
change to the word "Value" this indicates the fault code
number that occurred.
4. Pressing "AUTO" button will return to the original "F1" and
"Param" display.
5. Pressing buttons marked UP "▲" or DOWN "▼" will scroll
through the fault log.
6. Fault indicators - "F1 to F4" - are the last four faults that were
recorded by the CPMD, and they might get repeated if the
fault has re-occurred. Fault indicators - "FA to Fd" - are the
last four types of faults that have occurred in this CPMD, and
they will only repeat if a different type of fault has occurred
since the last time this type of fault occurred.
7. If no buttons are pushed after sixty (60) seconds the wall
control will reset to the "OFF" state. The procedure to enter
the fault code history log must then be re-initiated.
8. Clear fault code once you have diagnosed the fault. Whilst
in fault code mode press and hold the "COOL" button for five
(5) seconds.

RED COLOURED LED

This LED indicates the status of the conductivity measurement
circuit and the status of the Salinity Control Method.
Salinity
LED Control Conductivity Circuit Status
Method
1 Flash then 2 Water Manager Measured conductivity is below the conductivity
seconds OFF set point
2 Flashes then Water Manager Measured conductivity is above the conductivity
2 seconds set point
OFF
3 Flashes then Fill count Not measured
2 seconds
OFF
5 Flashes then No water control function
2 seconds
OFF
Continuously All Lower probes are open circuit or conductivity is
ON less than 9uS/cm
| CW-P15 Indirect Evaporative Cooler 859740-G
31

TRI-COLOURED LED

This LED indicates the status of the cooler and indicates Fault
Codes (if applicable).
Cooler Fault
LED
Status Description
2 Green Normal The main program
flash Operation loop is running, no
then 2 Fault present.
seconds
OFF
1 Red Communication Wall Control: No
Flash Failure valid message for
then 2 10 seconds. System
seconds shuts down.
OFF
2 Red Failure to Water has 20
Flashes detect water at minutes to reach the
then 2 low probe LOW probe when
seconds the solenoid valve
OFF is on. If it fails to do
so the Fan motor
and pump shut down
and this Fault is
activated.
3 Red Failure to Once water has
Flashes detect water at reached the LOW
then 2 high probe probe, water has
seconds 20 Minutes to reach
OFF the HIGH probe. If
it fails to do so the
Fan motor and pump
shut down and this
Fault is activated.
4 Red Failure to clear When the drain has
Flashes low probes opened water has
then 2 during drain 20 minutes to clear
seconds the LOW probe. If
OFF it fails to do so the
Fan motor and pump
shut down and this
Fault is activated.
This will occur after
a timed Drain delay
when the Pump has
been switched off,
or during a Salinity
Drain.
5 Red Water detected Low probe is dirty
Flashes at high probe or faulty. If it fails
then 2 but not at low to detect, the Fan
seconds motor and pump
OFF shut down and this
Fault is activated.
6 Red Failure to clear If after 4 hours of
Flashes high probe pump running water
then 2 has not cleared the
seconds HIGH probe (i.e.
OFF pumps not working),
If it fails to do so the
Fan motor and pump
shut down and this
Fault is activated.
7 Red Motor Error If an Error has
Flashes Supply Fan occurred in the
then 2 motor drive circuit.
seconds
OFF
MagIQcool MagIQtouch
Fault Code Fault Code
Fault Code #1 01
Fault Code #2 02
Fault Code #3 03
Fault Code #4 04
Fault Code #5 05
Fault Code #6 06
Fault Code #7 07