Requirement For Compliance With Lvd Directive - Mitsubishi Electric MELSEC-F FX3G Series User Manual

FX Series Programmable Controllers
3G
User's Manual - Hardware Edition

Requirement for Compliance with LVD directive

The following products have shown compliance through direct testing (of the identified standards below) and
design analysis (through the creation of a technical construction file) to the European Directive for Low
Voltage (2014/35/EU) when used as directed by the appropriate documentation.
Type : Programmable Controller (Open Type Equipment)
Models : MELSEC FX
from November 1st, 2008
from December 1st, 2008
from March 1st, 2009
from December 1st, 2009
For the products above, PLCs manufactured
before May 31st, 2018 are compliant with EN61131-2: 2007,
PLCs manufactured after June 1st, 2018 are compliant with EN61131-2: 2007 and EN61010-2-201: 2013.
*1. For some models, PLCs manufactured in March, 2018 are compliant with LVD directive successively.
EN61131-2:2007 Programmable controllers
EN61010-2-201:2013 Safety of electrical equipment for
Models : MELSEC FX
from July 1st, 1997
from April 1st, 1998
from August 1st, 1998
from August 1st, 2005
from September 1st, 2010 FX
For the products above, PLCs manufactured
before March 31st, 2002 are compliant with IEC1010-1
from April 1st, 2002 to April 30th, 2006 are compliant with EN61131-2:1994+A11:1996+A12:2000
from May 1st, 2006 to April 30th, 2018 are compliant with EN61131-2:2007
after May 1st, 2018 are compliant with EN61131-2: 2007 and EN61010-2-201: 2013.
*1. For some models, PLCs manufactured in March, 2018 are compliant with LVD directive successively.
IEC1010-1:1990 Safety requirements for electrical
/A1:1992 equipment for measurement, control,
EN61131-2:1994 Programmable controllers
/A11:1996 - Equipment requirements and tests
/A12:2000
EN61131-2:2007 Programmable controllers
EN61010-2-201:2013 Safety of electrical equipment for
series manufactured
3G
FX - MT/ES
3G
Where indicates:14,24,40,60
FX - MR/ES
3G
Where indicates:14,24,40,60
FX - MT/ESS
3G
Where indicates:14,24,40,60
FX - MR/DS
3G
Where indicates:14,24,40,60
Standard
- Equipment requirements and tests
measurement, control, and test
series manufactured
2N
FX - ER-ES/UL
2N
Where indicates:32,48
FX -16EYR-ES/UL
2N
FX -48ER-DS
2N
FX -48ER-UA1/UL
2N
FX -8ER-ES/UL
2N
-8EYR-S-ES/UL
2N
Standard
and laboratory use
- General requirements
- Equipment requirements and tests
measurement, control, and test
The equipment has been assessed as a component for fitting in a suitable
control box which meets the requirements of EN61131-2:2007
The equipment has been assessed as a component for fitting in a suitable
control box which meets the requirements of EN61010-2-201:2013
FX - ET-ESS/UL
2N
FX -8EYR-ES/UL
2N
The equipment has been assessed as a component for fitting in a
suitable control box which meets the requirements of IEC 1010-
1:1990+A1:1992
The equipment has been assessed as a component for fitting in a
suitable control box which meets the requirements of EN61131-
2:1994+A11:1996+A12:2000
The equipment has been assessed as a component for fitting in a
suitable control box which meets the requirements of EN61131-
2:2007
The equipment has been assessed as a component for fitting in a
suitable control box which meets the requirements of EN61010-2-201:
2013
Remark
*1
Remark
Standards
*1
17