Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Christie Crimson
Summary of Contents for Christie Crimson
- Page 1 Technical Reference 020-102660-01 Crimson and Crimson Mirage Serial Commands...
- Page 2 The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
-
Page 3: Table Of Contents
Communicating with Crimson........ - Page 4 FIB–Christie Link Video Mode........
- Page 5 Asynchronous messages......... . . 53 Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 6: Communicating With Crimson
Communicating with Crimson Understand the information and procedures for communicating with Crimson from a remote location. Product documentation For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product. -
Page 7: Related Documentation
Once you have connected your computer to either the RS232 IN port (depending on which standard is supported by your computer) or to the Ethernet port on Crimson, you can remotely access controls and image setups, issue commands or queries, and receive replies. -
Page 8: Setting Up The Ethernet
Ethernet is setup to obtain an IP address automatically if a DHCP server is on the network. To modify IP settings, or manually enter an address. Christie recommends using the Ethernet port on the IMXB as the HDBaseT port is limited to 100 Mb/s. You cannot change the IP settings using the web interface. -
Page 9: Basic Message Structure
(+) character to separate the code and subcode. If there is no subcode, the plus sign (+) is also omitted. In messages sent to Crimson that have a subcode, a space between the subcode and the first parameter (or special character) is optional. -
Page 10: Special Characters For Text
For additional reassurance and/or maximum message integrity, insert one or two special characters. Message Description requirement Acknowledgments For assurance from Crimson (or group of projectors) that a set message has been processed, request an acknowledgment. Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. -
Page 11: Error Messages
The acknowledgment is returned after the message has been received and fully executed by Crimson (such as in the case of a source switch it is not sent until the switch is complete). If the message cannot be executed for some reason (such as invalid parameters, time-out, and so on) a NAK is returned instead (not-acknowledge). -
Page 12: Descriptive Error
10 extra characters or they may be lost (such as, Crimson can accommodate the receipt of up to 10 more bytes after it sends 13h (Xoff)). When the buffer is once again available, Crimson sends a 11h (Xon) command to resume transmission. -
Page 13: Serial Api Commands
Serial API commands The Crimson commands can be used to modify product settings. ADR–Projector Address Sets or queries the device address. This command also helps to identify where a response or asynchronous message originates from. Generally, this command is used for projectors that are daisy-chained together using the RS232 style communication. -
Page 14: Alc-Ambient Light Correction
Turn off auto power: (APW 0) Turn on auto power: (APW 1) Related information PWR–Power (on page 43) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 15: Asu-Auto Setup
(BDR+PRTA?) Result: (BDR+PRTA!006 "115200") Set the baud rate on port A to 115200 bits per second: (BDR+PRTA 6) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 16: Bgc-Gamma Function
Select a Power Law function with a 2.6 exponent: (BGC 2) Result: (GAM 2600) BST–Built-in Self Test Performs self-checks in Crimson that can be safely executed either in standby, on, or cool down mode. Do not execute this command while Crimson is warming up. Commands Command Description... - Page 17 Run all tests successfully: (BST 0) Result: (BST!000 "--Passed--") Example of failed tests within the All Tests test suite: (BST 0) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 18: Cca-Color Adjustment
This command is only available if the video green> electronics are on and Custom is selected. CCA+GNCY <y coordinate for (Saved value) green> Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... - Page 19 3350 corresponds to x=0.3350 being adjusted. red> in the CIE 1931 chromaticity scale. CCA+GNPX <x coordinate for green> Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
- Page 20 Save the current color primary settings as the new calibrated defaults: (CCA+SAVE) Reset the color primary settings to the saved calibrated defaults: (CCA+RSET) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 21: Cle-Color Enable
Set the color space to RGB (full range) irrespective of which channel is selected: (CSP 1) Set the projector to always automatically detect the color space: (CSP 0) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 22: Ddd-Disable Dual-Link Dvi Inputs
Enables or disables the Art-Net interface. 0 = Disables the Art-Net interface (Default) 1 = Enables the Art-Net interface Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 23: Dtl-Sharpness
1 to 4 = Selects one of the four black level video electronics are on. (Saved value) blends, if available Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 24: Ebl-Edge Blending Selection
Configures which EDID is presented using inputs that support EDIDs (such as DisplayPort, HDMI, DVI, and so on). Use this command to configure what Crimson advertises regarding the type of signals it accepts. This command does not need to be set to accept a particular type of signal. -
Page 25: Etp-Engine Test Pattern
241 = Edge Blend Grid (Blue) 242 = Edge Blend Grid (White) 243 = 17 Point 244 = Magenta 245 = Cyan Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 26: Evt-Event Manager
(EVT!003 "2013-03-17 04:01:13.824" "Error" "(SST+TEMP?000) Integrator Rod Temperature (Temp 1) = Communication fault (shutdown)") (EVT!"--END--") Retrieve two most recent events: Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 27: Fcs-Lens Focus Position Adjustment
= A numeric value subject to the range returned in FCS?m Examples Move lens focus to position 500: (FCS 500) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 28: Fib-Christie Link Video Mode
Sets the delay between the input sync timing and the output sync timing. The actual delay can vary based on the amount of processing applied to the image. Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... - Page 29 Query the actual frame delay, in microseconds: (FRD+TIME?) Result: (FRD+TIME!"33.33") Query the actual frame delay for a Dual-Input 3D configuration, in microseconds: (FRD+TIME?) Result: Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 30: Frz-Image Freeze
Open or close the shutter without any fading effect: (FTB+TIME 0) Set the fade time to 500 milliseconds: (FTB+TIME 50) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 31: Gam-Gamma Power Value
Controls or monitors the state of the general purpose inputs and outputs. The pins reserved for 12V and ground cannot be read, set, or configured. For a mapping of the IO pins to the physical connector pins, refer to the Crimson User Manual (P/N: 020-102649-XX). Commands... -
Page 32: Itp-Test Pattern
14 = Diagonal Ramp 15 = Square Grid 16 = Diagonal Grid 17 = Maximum Activity 18 = Prism/Convergence Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... - Page 33 1 to 5 Ramp, and Diagonal Ramp test patterns. 1 (Default) This command is only available if video electronics are Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 34: Ken-Keypad Enable
Moves all lens motors back to the center flag for each — axis and sets their respective positions to 0. Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 35: Lho-Lens Horizontal Position Adjustment
It can also be used to move the lens to a relative position or to start and stop the motors arbitrarily. This command is only enabled when the projector is on. Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... - Page 36 Start moving the zoom motor towards the negative max position: (LMV+ZRUN -1) Move the horizontal motor 45 steps in the positive direction: Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©...
-
Page 37: Loc-Localization Settings
Get the language: (LOC+LANG?) Result: (LOC+LANG!001) Set the language to French: (LOC+LANG 1) Set the temperature to Fahrenheit: (LOC+TEMP 1) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 38: Loe-Video Loop Out Enable
Adjust the color balance by subtracting 10.0% red and 5.0% blue light: (LPP+REDA -100) (LPP+GRNA 0) (LPP+REDA -50) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 39: Lvo- Lens Vertical Position Adjustment
Get current menu position preset: (MSP?) Set the on-screen display position to the top left corner of the screen: (MSP 0) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 40: Net-Network Setup
NET+MAC0? Returns the MAC address of the Ethernet port. (Read- — only) NET+PORT? Returns the TCP port used for the Christie serial 1024 to 49151 (with some protocol over Ethernet. (Read-only) exceptions) 3003 = Reserved on the projector and cannot be... -
Page 41: Osd-On Screen Display
4096. (Read-only) OTR+VRES? Returns the maximum number of rows for the display. Always — returns 2160. (Read-only) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 42: Png-Ping
Selecting an empty profile does not do anything. 1 = <custom 1> 2 = <custom 2> 3 = <custom 3> 4 = <custom 4> Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 43: Pwr-Power
(Saved value) 2 = Free Access—Executes commands at the operator level unless a separate login is performed (Default) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 44: Shu-Shutter
Values SIN?L Returns a list of available inputs to select based on the — selected port configuration. (Read-only) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 45: Snm-Snmp Configuration
Enables or disables temperature 0 = Disables temperature faults faults. (Saved value) 1 = Enables temperature faults (Default) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 46: Sor-Screen Orientation
7 = Black (Default) SST–Status Returns status information about the projector in read-only mode. For more information about the status groups, items, and theirs state, see the Crimson Crimson and Mirage Status System Guide (P/N: 020-102661-XX). Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. -
Page 47: Szp-Resize Presets
By default, the projector scales all video to the full screen with the exception of 16:9 content. 16:9 content is scaled to 3840 x 2160 with black pillar boxes on either side. Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 48: Tdd-3D Sync Delay
TDM–3D Mode Controls when input signals are processed as 3D or not. Only applies to: Mirage HD25, Mirage WU25 Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 49: Tdn-Invert 3D Input
0 = Configures the 3D Sync OUT port to be value) fed directly to a 3D emitter, including any Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 50: Tdt-3D Test Pattern
(TMD+DATE "2018/01/17") Result: (65535 00000 FYI00916 "Setting Date to 2018/01/17") Get the local time: (TMD+TIME?) Result: (TMD+TIME! "19:45:23") Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 51: Uid-User Id
1 to 4 = Selects one of four warp maps, if video electronics are on. (Saved value) available Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 52: Zom-Lens Zoom Position Adjustment
Get the current minimum and maximum values for the zoom axis: (ZOM?m) Result: (ZOM!M-2400 900) Move the lens to position 500 for the zoom motor: (ZOM 500) Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... -
Page 53: Asynchronous Messages
• An OK or warning state to an error state. (65535 00000 ERR00000 "System Error: (SST+VERS?003) Image Processor HW Version = Detection Fault") Crimson and Crimson Mirage Technical Reference–Serial Commands 020-102660-01 Rev. 1 (07-2018) Copyright 2018 Christie Digital Systems USA, Inc. All rights reserved. ©... - Page 54 Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888 ph: +49 2161 664540 ph: +27 (0)11 510 0094 ph: +44 (0) 118 977 8000...