Page 1
Installation and Setup Guide 020-103451-02 CP2306-RGBe, CP2308-RGBe, CP2310-RGBe...
Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection with the performance or use of this material.
Page 3
关于 中 国《 电 子信 息 产品 污 染控 制 管理 办 法》 的 说明 • Environmentally Friendly Use Period 环保 使 用期 限 The year number in the centre of the label indicates the Environmentally Friendly Use Period, which is required to mark on the electronic information product sold in China according to the China RoHS regulations.
Page 6
For protection from ultraviolet radiation, keep all product housings intact during operation. • UV EXPOSURE! Protective UV safety glasses with side shields and Christie approved protective safety clothing must be worn when performing optical adjustments or servicing the product. •...
Page 8
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power.
Page 9
Electrical Hazard Risk of electric shock. Do not remove the product enclosure. Only Christie qualified technicians are authorized to service the product. General hazard. Electrocution hazard. To avoid personal injury, always disconnect all power sources before performing maintenance or service procedures.
Page 12
CP2308-RGBe, CP2310-RGBe projection systems. This projector is intended for use in a cinema environment. Only Christie qualified technicians who are knowledgeable about the hazards associated with high- voltage, ultraviolet exposure, and the high temperatures generated by the projector are authorized to assemble, install, and service the projector.
Page 13
• Stacking kit, including stacking cups, locking brackets, and required screws For installation, setup, and user information, see the product documentation available on the Christie Digital Systems USA Inc. website. Read all instructions before using or servicing this product. CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Installation and Setup Guide 020-103451-02 Rev.
Page 14
2. On the product page, select the model and switch to the Downloads tab. Additional information on this product is available in the following documents. • CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Product Safety Guide (P/N: 020-103453-XX) • CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Guide (P/N: 020-001835-XX) •...
Page 16
Lock 2. Extend or retract the feet. 3. When the adjustment is correct, tighten the lock nut. To stack CP2306-RGBe, CP2308-RGBe, CP2310-RGBe projectors, use the stacking kit provided. The stacking kit includes these parts: Locking bracket (quantity 4) Stacking cup (quantity 4) M6 screw (quantity 4) When stacking projectors, the optical axis of the projectors must be parallel to one another.
Page 22
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • SHOCK HAZARD! Only use the AC power cord provided with the product or recommended by Christie.
Page 25
If the LED is red, an error has occurred. Restart the Christie IMB. If the LED remains red, return the Christie IMB to Christie Digital Systems USA Inc. Indicates marriage status. In full power mode, a green LED indicates that the projector is properly married and encrypted content can be displayed.
Page 27
If the image suffers from slight keystone effect, it can be corrected with electronic cropping. If the keystone effect is severe, you can unevenly adjust the feet to compensate for projector tilt. Christie recommends using the lens offset to align the center of the image to the center of the screen before you correct the keystone effect.
Page 28
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 30
When adjusting boresight, you must maintain the boresight distance from the lens to the prism plane set by Christie. For example, when you move the top screw outward, turn the bottom two boresight screws to maintain the overall distance.
Page 31
Contact your Christie accredited service technician to correct DMD convergence issues. Learn how to align the fold mirror with the optical system to correct an image with missing or shadowy corners or edges.
Page 32
Adjusting the image Using a colorimeter, measure the colors displayed on the screen from the center of the audience viewing location. For more information, see the CP2306-RGBe, CP2308-RGBe, CP2310-RGBe User Manual (P/N: 020- 001835-XX). CP2306-RGBe, CP2308-RGBe, CP2310-RGBe Installation and Setup Guide 020-103451-02 Rev.