Graco E-Flo DC Series Instructions Manual page 47

Display Display Display Applicable Applicable Applicable
Code Code Code Motor Motor Motor
EBC_ Advanced
EBC_ EBC_
ELI_ ELI_ ELI_ Basic and
Advanced
ERR0_ Basic and
ERR0_ ERR0_
Advanced
F1F0
F1F0 F1F0
F2F0
F2F0 F2F0
K1D_
K1D_ K1D_ Advanced
K2D_
K2D_ K2D_ Advanced
K3D_
K3D_ K3D_ Advanced
K4D_
K4D_ K4D_ Basic and
Advanced
L1A0
L1A0 L1A0
L1AF L1AF L1AF Advanced
L2A0 L2A0 L2A0 Advanced
L3A0 L3A0 L3A0 Advanced
L4A0 L4A0 L4A0
L6CA L6CA L6CA
L6CB L6CB L6CB
MND_ MND_ MND_
Advanced
P1CB
P1CB P1CB Advanced
P1D_ Advanced
P1D_ P1D_
P9D_ Advanced
P9D_ P9D_
P1I_ Advanced
P1I_ P1I_
P2I_ P2I_ P2I_ Advanced
P2CB P2CB P2CB Advanced
P3CB P3CB P3CB Advanced
P3I_ P3I_ P3I_ Advanced
P4CB
P4CB P4CB Advanced
P4I_
P4I_ P4I_ Advanced
3A3453H
Blink Blink Blink Alarm Alarm or or or Alarm
Code Code Code Deviation Deviation Deviation
None Advisory Run/Stop switch in Stop position (closed).
4–5 Deviation Deviation hot board reset.
2–5 Deviation Deviation software error.
None Alarm
Fill pump flow not detected. The primary tank level has not
increased with the no flow timeout window and the no flow
timeout event is set to alarm.
None Deviation Fill pump flow not detected. The primary tank level has not
increased with the no flow timeout window and the no flow
timeout event is set to deviation.
1–2 Alarm Flow is below minimum limit.
None Deviation Flow is below minimum limit.
None Deviation Flow exceeds maximum target; also indicates pump runaway
condition exists.
1 Alarm Flow exceeds maximum target; also indicates pump runaway
condition exists.
None Alarm The flow rate is above the current profile flow limit set on Profile
Screen 3.
None Alarm While the system was in off production mode, the current tank
level dropped 3% below the value that was recorded when the
pump entered off production.
None Deviation The primary tank current level is below the primary tank deviation
set point.
None Deviation The primary tank current level is above the primary tank deviation
set point.
None Alarm The primary tank level is above the primary tank level high alarm
set point.
None Deviation Port 8 is enabled and the current draw is less than 4 mA. The
BPR is requesting a value greater than 0%. Verify that the device
is connected.
None Deviation Port 9 is enabled and the current draw is less than 4 mA. Verify
that the device is connected.
None Advisory Maintenance counter is enabled and countdown reached zero
(0).
None Alarm Pressure transducer 2 pressure is below the alarm set point.
None Deviation Unbalanced load. Dual Lower system — P1D1 = Motor 1 is
requiring less force to hold speed; pump lower may need service.
P1D2 = Motor 2 is requiring less force than motor 1 to hold speed.
None Deviation Major unbalanced load — see P1D_ (P9D_ is higher magnitude)
1–3 Alarm Pressure is below minimum limit.
None Deviation Pressure is below minimum limit.
None Deviation Pressure transducer 2 pressure is below the deviation set point.
None Deviation Pressure transducer 2 pressure is above the deviation set point.
None Deviation Pressure exceeds maximum target.
None Alarm Pressure transducer 2 pressure is above the alarm set point.
1–4 Alarm Pressure exceeds maximum target.
Error Code Troubleshooting
Description Description Description
47