Daikin Altherma 3 GEO Series Installer's Reference Manual page 247

10/11
Field settings table
Breadcrumb Field code Setting name
9.I [C-04] Bivalent hysteresis temperature.
9.I [C-05] What is the thermo request contact type for the main zone?
9.I [C-06] What is the thermo request contact type for the add. zone?
9.I [C-07] What is the unit control method in space operation?
9.I [C-08] Which type of external sensor is installed?
9.I [C-09] What is the required alarm output contact type?
9.I [C-0A] --
9.I [C-0B] Brine pressure switch present?
9.I [D-00] Which heaters are permitted if prefer. kWh rate PS is cut?
9.I [D-01] Contact type of preferential kWh rate PS installation?
9.I [D-02] Which type of DHW pump is installed?
9.I [D-03] Leaving water temperature compensation around 0°C.
9.I [D-04] Is a demand PCB connected?
9.I [D-05] Is the pump allowed to run if prefer. kWh rate PS is cut?
9.I [D-07] --
9.I [D-08] Is an external kWh meter used for power measurement?
9.I [D-09] Is an external kWh meter used for power measurement?
9.I [D-0A] --
9.I [D-0B] --
9.I [E-00] Which type of unit is installed?
9.I [E-01] Which type of compressor is installed?
9.I [E-02] What is the indoor unit software type?
9.I [E-03] What kind of heater?
9.I [E-04] Is the power saving function available on the outdoor unit?
9.I [E-05] Can the system prepare domestic hot water?
9.I [E-06] Is a DHW tank installed in the system?
9.I [E-07] What kind of DHW tank is installed?
9.I [E-08] Power saving function for outdoor unit.
9.I [E-09] --
9.I [E-0B] Is a bi-zone kit installed?
9.I [E-0C] --
9.I [E-0D] --
9.I [E-0E] --
9.I [F-00] Pump operation allowed outside range.
9.I [F-01] Above which outdoor temperature is cooling allowed?
9.I [F-02] --
9.I [F-03] --
9.I [F-04] --
9.I [F-05] --
9.I [F-09] Pump operation during flow abnormality.
9.I [F-0A] --
9.I [F-0B] Close shut-off valve during thermo OFF?
9.I [F-0C] Close shut-off valve during cooling?
9.I [F-0D] What is the pump operation mode?
└─ Brine freezing temperature
9.M [A-04] What is the brine anti freeze temperature?
4P569818-1A - 2019.10
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/O
R/O
R/O
R/O
R/W
R/O
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
2~10°C, step 1°C
3°C
0: -
1: 1 contact
2: 2 contacts
0: -
1: 1 contact
2: 2 contacts
0: LWT control
1: Ext RT control
2: RT control
0: No
1: Outdoor sensor
2: Room sensor
0: Normally open
1: Normally closed
0
0: Not present
1: Present
0: None
1: BSH only
2: BUH only
3: All heaters
0: No
1: Active open
2: Active closed
3: Safety thermostat
0: No
1: Secondary rtrn
2: Disinf. Shunt
0: No
1: increase 2°C, span 4°C
2: increase 4°C, span 4°C
3: increase 2°C, span 8°C
4: increase 4°C, span 8°C
0: No
1: Pwr consmp ctrl
0: Forced off
1: As normal
0
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0
2
0~5
5: GSHP
1
0: Reversible (*1)
1: Heating only (*2)
4: 9W
0: No
1: Yes
0: No
1: Yes
0: No
1: Yes
1: Integrated
0: disabled
1: Enabled
1
0
0
0
0
0: Disabled
1: Enabled
10~35°C, step: 1°C
20°C
3
5
0
0
0: Disabled
1: Enabled
0
0: No
1: Yes
0: No
1: Yes
0: Continuous
1: Sample
2: Request
0: 2°C
1: -2°C
2: -4°C
3: -6°C
4: -9°C
5: -12°C
6: -15°C
7: -18°C
Installer setting at variance with
default value
Date Value
(*1) *X*_(*2) *H*