Daikin Altherma 3 GEO Installation Manual
Hide thumbs
Also See for Altherma 3 GEO:
- Installer's reference manual (252 pages) ,
- User reference manual (36 pages) ,
- Installation manual (48 pages)
Related Manuals for Daikin Altherma 3 GEO
Summary of Contents for Daikin Altherma 3 GEO
- Page 1 Installation manual Daikin Altherma 3 GEO EGSAH06DA9W EGSAH10DA9W Installation manual EGSAX06DA9W(G) English Daikin Altherma 3 GEO EGSAX10DA9W(G)
- Page 2 3P570461-1A...
- Page 3 3P570461-1A...
-
Page 4: Table Of Contents
▪ Format: Paper (in the box of the unit) + Digital files on http:// 6.2.2 Configuration wizard: Time and date ......24 www.daikineurope.com/support-and-manuals/product- 6.2.3 Configuration wizard: System ........24 information/ 6.2.4 Configuration wizard: Backup heater ......26 Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 5: About The Box
▪ A subset of the latest technical data is available on the regional Daikin website (publicly accessible). Mind the following guidelines when handling the unit: ▪ The full set of latest technical data is available on the Daikin extranet (authentication required). >200... -
Page 6: Opening And Closing The Unit
WARNING Make sure installation, servicing, maintenance and repair comply with instructions from Daikin and with applicable legislation (for example national gas regulation) and are executed only by authorised persons. Opening and closing the unit 3.2.1... -
Page 7: To Remove The Hydro Module From The Unit
6 Unlink the connectors that run from the hydro module to the main switch box or other locations. Route the wires through the grommets of the upper hydro module cover. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 8: To Close The Indoor Unit
2 Connect the drain hose to the drain. See "3.3.2 To connect the The hydro module is heavy. It requires at least two persons drain hose to the drain" on page 9. to carry it. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 9: To Connect The Drain Hose To The Drain
In case of plastic pipes, make sure they are fully oxygen diffusion tight according to DIN 4726. The diffusion of oxygen into the piping can lead to excessive corrosion. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 10: To Connect The Brine Level Vessel
1 Install the shut off-valve with integrated filter (delivered as accessory) at the space heating/cooling water inlet. 2 Connect the space heating/cooling in pipe to the shut-off valve and the space heating/cooling out pipe to the unit. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 11: To Connect The Recirculation Piping
International Technical Standard setting the limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and ≤75 A per phase.). …is valid in the following cases: EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 12: Overview Of Electrical Connections For External And Internal Actuators
[9.9.E] Current sensor offset Safety thermostat "5.12 To connect the safety thermostat (normal closed contact)" on page 19. Brine low pressure "5.13 To connect the brine low switch pressure switch" on page 19. LAN adapter "5.14 LAN adapter" on page 20. connections Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 13: To Connect The Main Power Supply
(1N~) 3 Preferential kWh rate power supply without separate normal kWh rate power supply C1: Preferential kWh rate power supply (3N~ or 1N~) C2: Preferential kWh rate power supply contact EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... - Page 14 Connect the preferential kWh rate power supply contact (S1S) as 1× follows. Detail C4: Connection of X11Y 2× Factory-mounted cables. Disconnect X11Y from X11YA, and connect it to X11YB. X2M/5+6 1× X11YB X11Y X11YA 1× Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02...
-
Page 15: To Connect The Remote Outdoor Sensor
1 Connect the external temperature sensor cable to the indoor unit. 1× 1× Factory-mounted cable Splicing connectors (field supply) 3 Fix the cable with cable ties to the cable tie mountings. Remote outdoor sensor cable (40 m)(delivered as accessory) EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 16: To Connect The Electricity Meters
[9.2.3] DHW pump schedule 14a 21 switch box and main switch 1 Open the following (see "3.2.1 To open the indoor unit" on page 6): Installation of EKRP1HB is required. Cable sleeve (field supply) Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 17: To Connect The Space Cooling/Heating On/Off Output
3 Fix the cable with cable ties to the cable tie mountings. To connect the space cooling/ heating ON/OFF output Wires: (2+1)×0.75 mm² Maximum load: 3.5 A, 250 V AC — 1 Open the following (see "3.2.1 To open the indoor unit" on page 6): EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 18: To Connect The Changeover To External Heat Source
4 Main switch box cover appropriate terminals as shown in the illustration below. 2 Connect the power consumption digital inputs cable to the appropriate terminals as shown in the illustration below. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 19: To Connect The Safety Thermostat (Normal Closed Contact)
We recommend to use a mechanical brine pressure switch. If an electrical brine pressure switch is used, capacitive currents might disturb the flow switch operation causing an error on the unit. Wires: 2×0.75 mm² EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 20: Lan Adapter
System requirements Cut loop wires coming from A16P/X13A/1+4 (factory mounted) The requirements posed on the Daikin Altherma system depend on Splicing connectors (field supply) the LAN adapter application/system layout. Wires from the brine low pressure switch cable (field... -
Page 21: Overview Of Electrical Connections
It is recommended to connect the LAN adapter to the management router directly. Depending on the wireless bridge or power system + line adapter model, the system might not function properly. 230 V AC detection voltage (X1A) EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 22: Electricity Meter
Connector X1A is for the connection of the LAN adapter to the digital 4 Main switch box cover outputs of a solar inverter/energy management system, and allows for the integration of the Daikin Altherma system in a Smart Grid application. 2 Connect the electricity meter to LAN adapter terminals X1A/N+L supply a 230 V AC detection voltage to the input contact of... -
Page 23: Configuration
▪ Afterwards. If necessary, you can make changes to the solar inverter/energy management system to LAN adapter configuration in the menu structure or the overview settings. digital inputs X1A/1+2 LAN. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 24: To Access The Most Used Commands
1 Set the user permission level to Installer. See "To — The indoor unit type is displayed, but cannot be adjusted. change the user permission level" on page 24. 2 Go to [9.I]: Installer settings > Overview field settings. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... - Page 25 The system can supply leaving water to up to 2 water temperature zones. During configuration, the number of water zones must be set. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02...
-
Page 26: Configuration Wizard: Backup Heater
It is important to set Emitter type correctly and in accordance with your system layout. Indicates if the desired leaving water temperature is according to a schedule. Also see "6.2.5 Configuration wizard: Main zone" on page 26. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 27: Detailed Screen With Weather-Dependent Curve
Select slope or offset. Increase or decrease the slope/offset. When slope is selected: set slope and go to offset. When offset is selected: set offset. Confirm changes and return to the submenu. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 28: Configuration Wizard: Tank
It is the desired temperature when a storage Code Description economic action is scheduled (preferably during day). [8.3] Number that users can call in case of Code Description problems. [5.3] [6-0B] Eco setpoint ▪ 30°C~min(50,[6‑0E])°C Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 29: Brine
▪ error "U4" appears on the user interface, ▪ the heat pump module is connected to preferential kWh rate power supply where power supply is interrupted and preferential kWh rate power supply is activated. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 30: Menu Structure: Overview Installer Settings
Ext. amb. sensor offset Averaging time [9.C] Bivalent Bivalent Boiler efficiency Temperature Hysteresis Only applicable in Swedish language. INFORMATION Depending on the selected installer settings and unit type, settings will be visible/invisible. Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 31: Commissioning
NOT been 1 Go to Stop air purge. bypassed. 2 Select OK to confirm. The power supply voltage matches the voltage on the identification label of the unit. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 32: To Perform An Air Purge On The Brine Circuit
1 Go to Stop test run. 2 Select OK to confirm. Possible actuator test runs ▪ Backup heater 1 test (3 kW capacity, only available when no current sensors are used) Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 33: To Start Or Stop 10-Day Brine Pump Operation
▪ Explain the user how to properly operate the system and what to do in case of problems. ▪ Show the user what to do for the maintenance of the unit. EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... -
Page 34: Technical Data
9 Technical data Technical data A subset of the latest technical data is available on the regional Daikin website (publicly accessible). The full set of latest technical data is available on the Daikin Business Portal (authentication required). Piping diagram: Indoor unit... -
Page 35: Wiring Diagram: Indoor Unit
Only for preferential kWh rate Backup heater control PCB power supply with separate power supply with separate Inverter PCB normal kWh rate power supply normal kWh rate power supply * Demand PCB EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02... - Page 36 For safety thermostat (12) LAN adapter connection (12) LAN adapter connection Inrush Inrush current Ethernet Ethernet Max. load Maximum load LAN adapter LAN adapter Normally closed Normally closed Switch box Installation manual EGSAH/X06+10DA9W(G) Daikin Altherma 3 GEO 4P569811-1 – 2019.02...
- Page 37 Power limitation demand input 3 FIELD SUPPLY A8P: X801M: 3-5 signal 2 core Power limitation demand input 4 Router for LAN adapter A8P: X801M: 4-5 A15P: X4A signal ethernet 4D121919 EGSAH/X06+10DA9W(G) Installation manual Daikin Altherma 3 GEO 4P569811-1 – 2019.02...
- Page 40 4P569811-1 0000000S 4P569811-1 2019.02...
Need help?
Do you have a question about the Altherma 3 GEO and is the answer not in the manual?
Questions and answers