Daikin Altherma 3 GEO Series Installer's Reference Manual page 240

Field settings table
Breadcrumb Field code Setting name
3.5 [0-00] Leaving water value for high ambient temp. for LWT add zone heating WD curve.
3.5 [0-01] Leaving water value for low ambient temp. for LWT add zone heating WD curve.
3.5 [0-02] High ambient temp. for LWT add zone heating WD curve.
3.5 [0-03] Low ambient temp. for LWT add zone heating WD curve.
└─ Cooling WD curve
3.6 [0-04] Leaving water value for high ambient temp. for LWT add zone cooling WD curve.
3.6 [0-05] Leaving water value for low ambient temp. for LWT add zone cooling WD curve.
3.6 [0-06] High ambient temp. for LWT add zone cooling WD curve.
3.6 [0-07] Low ambient temp. for LWT add zone cooling WD curve.
Additional zone
3.7 [2-0D] Emitter type
└─ Setpoint range
3.8.1 [9-05] Heating minimum
3.8.2 [9-06] Heating maximum
3.8.3 [9-07] Cooling minimum
3.8.4 [9-08] Cooling maximum
Additional zone
3.A [C-06] Thermostat type
└─ Delta T
3.B.1 [1-0C] Delta T heating
3.B.2 [1-0E] Delta T cooling
└─ WD mode type
3.C WD curve type
Space heating / cooling
└─ Operation range
4.3.1 [4-02] Space heating OFF temp
4.3.2 [F-01] Space cooling OFF temp
Space heating / cooling
4.4 [7-02] Number of zones
4.5 [F-0D] Pump operation mode
4.6 [E-02] Unit type
4.7 [9-0D] Pump limitation
Space heating / cooling
4.9 [F-00] Pump outside range
4.A [D-03] Increase around 0°C
4.B [9-04] Overshoot
4.C [2-06] Antifrost
Tank
5.2 [6-0A] Comfort setpoint
5.3 [6-0B] Eco setpoint
5.4 [6-0C] Reheat setpoint
5.6 [6-0D] Heat up mode
└─ Disinfection
5.7.1 [2-01] Activation
(*1) *X*_(*2) *H*
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
[9-05]~min(45,[9-06])°C, step: 1°C
[2-0C]=0
22°C
[2-0C]=1
35°C
[2-0C]=2
25°C
[9-05]~[9-06]°C, step: 1°C
[2-0C]=0
45°C
[2-0C]=1
55°C
[2-0C]=2
65°C
10~25°C, step: 1°C
15°C
-40~5°C, step: 1°C
-40°C
[9-07]~[9-08]°C, step: 1°C
8°C
[9-07]~[9-08]°C, step: 1°C
12°C
25~43°C, step: 1°C
35°C
10~25°C, step: 1°C
20°C
0: Underfloor heating
1: Fancoil unit
2: Radiator
15~37°C, step: 1°C
15°C
[2-0C]=0
37~55, step: 1°C
55°C
[2-0C]≠0
37~65, step: 1°C
65°C
5~18°C, step: 1°C
5°C
18~22°C, step: 1°C
22°C
0: -
1: 1 contact
2: 2 contacts
3~10°C, step: 1°C
10°C
3~10°C, step: 1°C
5°C
0: 2-points
1: Slope-Offset
14~35°C, step: 1°C
16°C
10~35°C, step: 1°C
20°C
0: 1 LWT zone
1: 2 LWT zones
0: Continuous
1: Sample
2: Request
0: Reversible (*1)
1: Heating only (*2)
0~8, step: 1
0: No limitation
1~4: 50~80%
5~8: 50~80% during sampling
6
0: Restricted
1: Allowed
0: No
1: increase 2°C, span 4°C
2: increase 4°C, span 4°C
3: increase 2°C, span 8°C
4: increase 4°C, span 8°C
1~4°C, step: 1°C
4°C
0: Disabled
1: Enabled
30~[6-0E]°C, step: 1°C
60°C
30~min(50, [6-0E])°C, step: 1°C
45°C
30~min(50, [6-0E])°C, step: 1°C
45°C
0: Reheat only
1: Reheat + sched.
2: Scheduled only
0: No
1: Yes
3/11
Installer setting at variance with
default value
Date Value
4P569818-1A - 2019.10