Device Identification Details - INIM SmartLoop Series Installation Manual

2.11.2 Graphic conventions
Following are the graphic conventions used in the text.
Conventions
Text in Italics
Refer to
2.11.2 Graphic
conventions
<text> #<CustomerCode>
[uppercase [A] or [1]
letter] or
[number]
BUTTON CANC, ESC, RESET
Note:
The attached notes contain important information about the text.
Attention:
The "Attention" prompts indicate that total or partial disregard of the procedure could
damage the connected devices.
Danger:
The danger warnings indicate that total or partial disregard of the procedure could injure the
operator or persons in the vicinity.
2.12

Device identification details

Alimentazione /
Power / Alimentacion
Consumo /
Consumption / Consumo
Isolamento /
MADE IN ITALY
Isolation / Aislamiento
Approvato /
Approved / Aprobado
0051-CPD -0231
Figure 3 - Data labe
0051
09
0051 - CPD - 0228
Control and signalling system with integrated
power-source.
SmartLoop/1010-S
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
12
Example
paragraph
Text in italics: indicates the title of a chapter, section, paragraph, table
or figure in this manual or other published reference.
Variable data.
Representation of a part of the system or video object.
Computer or control panel keys.
1010/G
02/2012
230V~ -15% + 10%
50/60 Hz
0.9 A
I
Classe
EN54-2, EN54-4
Control and signalling system with integrated Control and signalling system with integrated
EN54-4: 1997/ A2: 2006
EN54-4: 1997/ A1: 2006 EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006 Isolation: Class I
Options with requirements: Isolation: Class I
- 7.8 Sounder circuits output
Options with requirements: - 7.11 Delayed outputs
- 7.8 Sounder circuits output - 7.12 Alarm on two points activation
- 7.11 Delayed outputs - 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling - 7.12 Alarm on two points activation
- 9.5 Points isolation - 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling - 10.0 Test condition
- 9.5 Points isolation
- 10.0 Test condition Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
description
0051
0051
09 09
0051 - CPD - 0231 0051 - CPD - 0228
power-supply device. power-supply device.
SmartLOOP/1010-G SmartLOOP/1010-S
Installation manual
0051
09
0051 - CPD - 0232
Control and signalling system with integrated
power-supply device.
SmartLOOP/1010-P
EN 54-2:1997+A1:2006
EN 54-4:1997+A1:2002+A2:2006
Isolation: Class I
Options with requirements:
- 7.8 Sounder circuits output
- 7.11 Delayed outputs
- 7.12 Alarm on two points activation
- 8.3 Fault from points signal
- 8.9 Monitored output for remote signalling
- 9.5 Points isolation
- 10.0 Test condition
Manufacturer: INIM Electronics s.r.l.
Address: via Fosso Antico, Centobuchi
63076, Monteprandone (AP), Italy
General information