8205-E6D With The System Or Logical Partition Power Turned Off; Replacing A Disk Drive Or Solid-State Drive In The 8202-E4B, 8202-E4C, 8202-E4D, 8205-E6B, 8205-E6C, Or 8205-E6D System Or Expansion Unit - IBM 8202-E4B Manual

v If you replaced the part because of a failure, verify the installed part. For instructions, see
"Verifying a repair" on page 177.
v If you installed the part for any other reason, verify the installed part. For instructions, see
"Verifying the installed part" on page 165.
3. To configure the newly installed disk drive or solid-state drive, see "Configuring a disk drive or
solid-state drive in an IBM i system or logical partition" on page 115.
4. To rebuild the data on the replacement disk drive or solid-state drive, see "Rebuilding data on a
replacement disk drive or solid-state drive by using IBM i" on page 118.
Replacing a disk drive or solid-state drive in the 8202-E4B, 8202-E4C,
8202-E4D, 8205-E6B, 8205-E6C, or 8205-E6D with the system or logical
partition power turned off
Learn to replace a failed Small Computer System Interface (SCSI) or serial-attached SCSI (SAS) disk drive
in a system or logical partition that controls the disk drive or solid-state drive location with the power
turned off.
To complete this procedure, you must have already completed the removal procedure. For the removal
procedure, see "Removing a disk drive or solid-state drive from the 8202-E4B, 8202-E4C, 8202-E4D,
8205-E6B, 8205-E6C, or 8205-E6D with the system or logical partition power turned off" on page 57If you
are installing a new or upgraded disk drive, see "Installing a disk drive or solid-state drive in the
8202-E4B, 8202-E4C, 8202-E4D, 8205-E6B, 8205-E6C, or 8205-E6D with the system or logical partition
power turned off" on page 26. If you are replacing a disk drive or solid-state drive as part of a service
procedure, continue to use the following procedure.
Complete the following tasks to replace a drive:
v Choose from the following options:
– "Replacing a disk drive or solid-state drive in the 8202-E4B, 8202-E4C, 8202-E4D, 8205-E6B,
8205-E6C, or 8205-E6D system or expansion unit"
– "Replacing a solid-state drive in the 5888 PCIe storage enclosure" on page 82 (This drive enclosure
is supported for the 8202-E4C and 8205-E6C systems.)
– "Replacing a solid-state drive in the EDR1 PCIe storage enclosure" on page 83 (This drive enclosure
is supported for the 8202-E4D and 8205-E6D systems.)
v "Completing the procedure" on page 84
Related information:
Removing and replacing a disk drive in the 5887 disk drive enclosure unit
Replacing a disk drive or solid-state drive in the 8202-E4B, 8202-E4C, 8202-E4D,
8205-E6B, 8205-E6C, or 8205-E6D system or expansion unit
Complete the following steps to replace a disk drive or solid-state drive in a system or in an expansion
unit:
1. If the slot you want to use contains a disk drive filler, remove the disk drive filler from the slot. For
instructions, see "Removing a disk drive filler from the 8202-E4B, 8202-E4C, 8202-E4D, 8205-E6B,
8205-E6C, or 8205-E6D" on page 92.
2. If the drive you are installing does not have a bezel preinstalled, then complete the tasks to install a
bezel on the drive, then continue with this procedure from step 4. For instructions to install a bezel,
see "Installing a disk drive bezel in a drive or filler for the 8202-E4B, 8202-E4C, 8202-E4D, 8205-E6B,
8205-E6C, or 8205-E6D" on page 95.
3. If the drive you are installing has a bezel preinstalled, then go to step 4.
4. Unlock the drive handle by squeezing it and pulling it out toward you. If the handle is not all the
way out, the disk drive or solid-state drive does not slide into the system or an expansion unit.
Disk drives or solid-state drives
81