Toro Multi Pro WM 41240 Operator's Manual page 55

Calibrating the Sprayer Speed
1. Ensure that the sprayer tank is filled with water.
2. On an open, flat area, mark off a distance
between 45–152 m (150–500 ft).
Note:
Toro recommends marking off 152 m
(500 ft) for more accurate results.
3. Start the engine and drive to the start of the
marked-off distance.
Note:
Align the center of the front tires with the
starting line for the most accurate measurement.
4. On the InfoCenter, navigate to the Calibration
menu and select Speed Calibration.
Note:
Selecting the Home Screen icon at any
time will cancel calibrations.
5. Select the Next arrow (→) on the InfoCenter.
6. Using the plus (+) and minus (-) symbols, enter
the marked-off distance into the InfoCenter.
7. Perform one of the following:
•
For HD-Series Models with a manual
transmission—shift the machine into first
gear and drive the marked distance in a
straight line at full throttle.
•
For the HDX-Auto model,—shift the
machine into D (drive ) and drive the marked
distance in a straight line at full throttle.
8. Stop the machine at the marked-off distance
and select the check mark on the InfoCenter.
Note:
Slow down and roll to a stop to align the
center of the front tires with the finish line, for
the most accurate measurement.
Note:
Calibration is now complete.
Calibrating the Boom Bypass
Important:
Select an open flat area to perform
this procedure.
Note:
Calibrating the boom bypass for machines
without a throttle lock requires 2 people.
1. Ensure that the sprayer tank is filled with water.
2. Set the transmission as follows:
•
For HD-Series Models with a manual
transmission—shift the transmission to
Neutral
•
For the HDX-Auto model—shift the
transmission to P (park).
3. Set the parking brake and turn the engine on.
4. Set the 3 boom switches to the On position, but
leave the
MASTER BOOM
switch off.
5. Set the switch to the On position, and turn
PUMP
on the agitation.
6. Set the engine speed as follows:
•
For machines without the optional throttle
lock—have 1 person press down on the
accelerator pedal until maximum engine
speed is reached.
Note:
The other person will adjust the boom
section-bypass valves.
•
For machines with the optional throttle
lock, press down on the accelerator pedal
until maximum engine speed is reached
and set the throttle lock; refer to operation
instructions for your Workman hand throttle
kit.
7. On the InfoCenter, navigate to the Calibration
menu and select Test Speed.
Note:
Selecting the Home Screen icon at any
time will cancel calibrations.
8. Using the plus (+) and minus (-) symbols, enter
a test speed of 5.6 Km/h (3.5 mph), then select
the Home icon.
9. Using the
APPLICATION RATE
application rate according to the table below.
Nozzle Application Rate Table
Nozzle Color SI (Metric)
Yellow 159 L/ha
Red 319 L/ha
Brown 394 L/ha
Gray 478 L/ha
White 637 L/ha
Blue 796 L/ha
Green 1,190 L/ha
10. Turn off the left boom and adjust the boom
bypass valve
reading is at the previously adjusted level
(typically 40 psi or 2.75 bar).
Note:
The numbered indicators on the bypass
valve are for reference only.
55
switch, adjust the
English
Turf
17 gpa 0.39 gpk
34 gpa 0.78 gpk
42 gpa 0.96 gpk
51 gpa 1.17 gpk
68 gpa 1.56 gpk
85 gpa 1.95 gpk
127 gpa 2.91 gpk
(Figure 74) until the pressure