Control Codes Summary By Code - Ithaca 150 Programmer's Manual

Programmer's Guide

Control Codes Summary by Code

Normal Second Hex Code
ASCII ASCII
field
[NUL] 00
[ENQ] <n> 05H
[BS] 08H
[HT] 09H
[LF] 0AH
[VT] 0BH
[FF] 0CH
[CR] 0DH
[SO] 0EH
[SI] 0FH
[DC2] 12H
[DC4] 14H
[CAN] 18H
[ESC] [SI] 1BH,0FH
[ESC] [DC1] 1BH,11H
[ESC] [DC3] 1BH,13H
[ESC] [DC4] 1BH,14H
[ESC] [EM] B 1BH,19H,
<n> 42H
[ESC] [EM] C 1BH,19H,
<n> 43H
[ESC] [EM] J 1BH,19H,
<n> 4AH
[ESC] [EM] V 1BH,19H,
<n> 56H
[ESC] # <0> 1BH,23H,
30H
[ESC] $ 1BH,24H
[ESC] % G 1BH,25H,
47H
[ESC] % H 1BH,25H,
48H
[ESC] * 1BH,2AH
<m><n>
1 <n> 2
[ESC] ! <n> 1BH,21H
[ESC] - <n> 1BH,2DH
[ESC] 0 1BH,30H
[ESC] 1 1BH,31H
[ESC] 2 1BH,32H
[ESC] 3 <n> 1BH,33H
12/14/99
PcOS Series 150
IPCL equivalent Description
code
Null
Set inquire status.
(Refer to command descriptions.)
&%BS Set back space.
&%HT Set horizontal tabs.
&%LF Set line feed.
&%VT Set vertical tabs.
&%FF Set form feed.
&%CR Set carriage return.
&%MW Se one-line double-wide print.
&%F1 Set 17 cpi.
&%F3 Set 10 cpi.
&%MN Cancel one-line double-wide print.
&%RP Clear print buffer.
&%F4 Set 24 cpi.
&%VO Open for validation.
&%VC Close for validation.
&%VS Select validation mode with
autoform sense.
&%BH <m > Set bar code height.
1
n=0 Restore defaults
n=1-9 Number of passes
(0.11" per pass)
&%ZC <m ><m > Set validation clamp delay.
1 2
&%BJ <m ><m > Set bar code justification.
1 2
&%ZV<m ><m > Set validation time-out.
1 2
&%QT Begin HSD mode.
Copy ROM character set to RAM
character set.
&%MI Begin italics.
&%CI End italics.
Print graphics in mode <m>.
&%CS<n> Select the International Character
Set.
&%CU {n=0} Set underline.
&%MU {n=1} n=0 end
n=1 begin
&%ST Set 1/8-inch line space.
&%SG Set 7/72-inch line space.
Begin variable line spacing.
(This enables [ESC] A <n>).
&%SV <m ><m > Set variable space n/216-inch.
1 2
<m > Where n=1..255 defines the feed
3
used by line feed.
Rev G
Control Codes
Summary by Code
Page
62
16
16
15
20
20
15
33
31
31
33
55
31
52
52
52
50
53
50
53
22
28
38
38
46
24
36
18
19
19
18
Page 81